ASKA ELECTRONICS F3L Wireless headphone User Manual

ASKA ELECTRONICS CO., LIMITED Wireless headphone

User Manual

BLUETOOTH STEREO HEADPHONEUser ManualGet started To know more about your F3L Bluetooth headphoneFeatures1,Bluetooth 4.22,3.5mm music line-in function3,Smart voice alerts4,Support connecting with 2 phones devices 5, iOS show the headphone battery power statusHow to use1, General Function 2, Basic Buttons OperationPower on: Press multifunction button for 2 seconds. Blue LED flashes 2 times. Headphone turn on.Power off: Press multifunction button for 3 seconds. Red LED turn off after flashes 2 times. Headphone turn off.Volume adjust: Each press on 'Volume up' or 'Volume down' buttons, one level voice volume changes. When volume reaches to Max or Minimum, "Tick" reminding voice occurs.Play/Pause: Short press multifunction button ,music pause. Press it again, music continues.Previous: Short press 'Previous' button, music turns to previous one.Next: Short press 'Next' button, music turns to next one.Answer Call: Short press multifunction button to answer the phone call.End call: Short press multifunction button, phone call ended.Reject call: Press 'Volume up' button, for 2 seconds to rejected a call.Transfer call: During the phone call conversation, press 'Volume up' button for 2 seconds, call switches to mobile phone. Press 'Volume up' button, for 2 seconds again, call switches to headphone. Last number redial: in standby status ,continuously press headphone multifunction button twice to redial the last number.Call Mute function: Press 'Volume down' button for 2 seconds, call mute. Press 'Volume down' button for 2 seconds again, call mute cancel.Battery Capacity status: When headphone connect to iOS devices, iOS devices show the headphone battery power status on the upper right corner.Charging: new headphone has enough power for pairing and dialing out for several times. When in low battery, please charging via USB cable for 2 hours. Red LED keep lighting during charging, blue LED keep lighting charging finished.Reset Mode: Connect the headphone to computer via Micro USB cable. When red LED light flashes ,headphone reset finished.3.5mm music line-in function：Connect Audio line in cable to 3.5 audio jack for wired music.Phone call function cannot be used in this modeThe headphone is on status (not connect with mobile phone )A) connect the 3.5 audio wire to the headphone andaudio player.B) you can adjust volume button of the mobile phoneto reach right volume to listen music.3, Pairing (One headphone support connecting 2 phone devices )Pairing with one phone or other deviceMake sure the headphone is power off.Press and hold the multifunctional button for 5 seconds to enter into the pairing mode.Red LED & Blue LED flashes alternately, Smart voice remind entering into pairing mode. Activate your phone or device Bluetooth function and search for headphone. from the list of found devices on your mobile phone , select the headphone“F3L” to connect it .follow the instruction to enter “0000” as PIN if the mobile phone reminder to need.Kit Contents1, 1 X Stereo Bluetooth headphone F3L2, 1 X Charging Micro USB Cable3, 1 X User Manual4, 1 X 3.5mm audio wireSpecificationBluetooth version: 4.2Talk time: 8h Stand-by time: 130hMusic play time: 6h Wireless range: 10mBluetooth profiles: A2DP / AVRCP/ HSP /HFPImpedance: 32ΩSpeaker diameter: 40mmSound pressure level: 103±3dBFrequency Response: 20Hz---20KHzSignal-To-Noise: ≥85dBDistortion: ≤1.0%Weight: 169.6gDimension: 176 x 166 x 65mm2 35 6 74Volume Down/Mute CallVolume Up/Reject CallHeadphone or device can be used to play your phone music or dial phone call etc.Pairing with two phones or other devices at the same timeThis headphone can support 2 devices multi-connection. It can pair with two mobile phones simultaneously, taking the call from any of them. 1.Pairing with the A phone successfuly,thenturn off the headphone.2.Do the same procedure with B phone.3.Then power off the headphone again.4.restart the headphone, it will automatically connectto the Phone B of Last connected , and short pressthe two key of “volume +” and “volume -”simultaneously ,can enable the multipoint Connectfunction, from the list of found devices on anothermobile phone A,select the headphone to connect it.Warning 1, You must choose a qualified charger from a r egular manufacturer to charge the headphone.2, You must charge the headphone if it has not been used for more than 12 months.Operation LED Status Power on Blue LED flashes 2 times Power off Red LED flashes 2 times Pairing Red LED & Blue LED flashes alternately Standby Blue LED flashes 3 times in 5 seconds Incoming call Blue LED flashes continuous Low battery Red LED flashes 2 times every 2 seconds Charging Red LED keep lighting during charging, Blue LED keep lighting charging finished.FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Navigation menu