Ardi Technology S04A02GP Digital RF Tracker 405 User Manual Exhibit E User Manual

Ardi Technology Corp. Digital RF Tracker 405 Exhibit E User Manual

User manual

Front & Rear ViewSpecificationsPackage Contents1. Slide out the battery cover. 2. Insert the batteries. Make sure that the polarity +/- of the battery follow the markings on the bottom of the battery compartment.Front BackSearch buttonSignal indicationDistance indicationPower on Power off BuzzerBattery coverMute buttonHanging hole for strapClip1332To search the Slave unit, please press the "Search button" on the Master unit once. If the distance between the Master and the Slave is closer, the more LED lights are lit and the melody on the Master is repider. Contrarily, if the distance between the Master and the Slave is farther, less LED lights are lit and the melody on the Master becomes slower. Use the LED and the melody indication as guides to find the Slave unit.If the distance between the Master and the Slave is out of detectable range and you turn to the wrong direction making the distance farther, the Master beeps every second to remind you to go back to the correct direction and detectable distance.While searching, the Slave makes low beep sounds every second. This can assist you in finding its position by tracking the sound when the Master and the Slave are already close. (Suggestion: Press and hold the Mute button on the Master to turn off the melody temporarily.Once you release the Mute button, the searching melody resumes again.)Press the "Search button" on the Master unit again to stop searching.While searching, always place the Master in front of your body and turn around slowly to find the connect direction by following singnal indicator and distance melody. If you point at the correct direction, the Master shows more LED lightand plays the melody more rapidly.. Holding Way*** Do not cover the top side of Master. CorrectHoldingWrong HoldingDuring Search CorrectHoldingWrong Holding *** Do not sway Master. Master is always in front the body when take a turn.Search Car Finder User Manual 2. Switch the power button of the Master and the Slave to “ON”, it will enter automatically ”Search Mode”, please press search button to enter ”Standby mode”.3. Place the Slave on valuable items that you want to locate, such as car, bicycle and others. Take the Master with you or clip it on your belt clip.Important: Do not put the Master in the car, it could be damaged by high temperature.3.Place the battery cover back.1.For the first time use, please insert the batteries into the Master and the Slave sets according to the battery installation instruction as follows.(the distance may be short depends on the terrain environment )-MasterFront BackModel NameFunctionSearch RangeAlarm TriggeredMaster/Slave Master (M05A)x1 Slave (S04A)x1 Master (M05AM)x1 Slave (S04AS)x1Battery Type LR44x2 CR2032x1 LR44x2 CR2032x1Battery Life Time with Standby None None 30 days (24 hrs) 30 days (24 hrs)Battery Life Time with Sleep 0~90 days 0~90 days Over 90 days Over 90 daysBeep Sound (at 10cm/3.9inch) 95 db 100 db 95 db 100 dbBulit-in None None Vibration Motor Vibration SensorDimension (L/W/H) 52.8x39x13.2mm2x1.x0.52inchDiam 45 x W 12mmDiam 1.77 x 0.47inch52.8x39x13.2mm2x1.x0.52inchDiam 45 x W 12mmDiam 1.77 x 0.47inchNone Vibration over one second 405CSearch Search & Alarm with Vibration405CA0~500 0~500Model Name 405CMaster(M05A) 1 setSlave(S04A) 1 setBatteries LR44x2CR2032x1User manualStrap92405CA1 set1 setLR44x2CR2032x1Alarm(Only for 405CA)A sensor is bulit-in to detect the vibration, while someone is trying to move your car, like violation tow, or a thiefis breaking your car window, the Car Finder will alert you in 1 second. The Master unit alarms and vibrates at this moment.Suggested Setting placeSearch Tip:
Signal indication LEDs flashevery secondMelody is rapiderMelody is slower and diminuendoSignal indication LEDs flashevery secondMelody is slower and short beep every second!(i) Search, detection, and alarm range can be affected on different.If the beep sound is not loud enough, the batteries may be low. Change with new batteries for louder alarm sound.This product only assists in providing a warning alarm to remind the user. It does not guarantee to prevent theft or robbery of personal property. batteriesyourbatteries sources. It may cause danger or even explosion.Sleeping Low battery AlarmDiasble Alarm funstion: During at standby mode, the master and Sllave wuthin 2 meters, power off the Master unit.Enable Alarm function: Switch the Master power on.MutePress the Mute botton to mute searching melody from the Master unit. Listen to beep sound from the Slave unit to assist short range searching.Switch the Power button to ONMore LEDs light upLEDs light decreasinglyTurn off the search melody of Master(long press the Mute button)SearchSignal indication LEDs flashSignal indication LEDs flashevery secondSignal indication LEDs flashevery secondHigh beeps while re-linkingHigh beep every secondLow batteryDisconnectUnder standy mode, press the”Search” buttonmayb.) When switching the Master unit power on, the Signal indication LED flashed as searching the Slave unit. If the Master and Slave units are out of working range, the Signal indication LED remains light while the Master unit could not find Slave unit.Switch the power button of the Master unit to OFF, when search function is not needed. Once you need thiskit to resume the standy mode, just turn the power button of the Master to ON.Important: a.) Please keep the Slave at ON status if you would turn the Master into Sleep mode.c.) Please trun off the Master and Slave unit if NOT in sue to save battery life.If you want to use the device on the airplane, please comply with the flight safety law according to each country.This product operation temperature is between 32ʲ ~140ʲÛ&aÛ&. Storage temperature is between -4ʲ ~185ʲÛ&aÛ&91E-02B4-U50G00** The connection range depends on the terrain environment because of readio efficiency.

Navigation menu