Carestream Health 4901 DRYVIEW CHROMA Imaging System incorporating RFID User Manual 9G4260

Carestream Health, Inc. DRYVIEW CHROMA Imaging System incorporating RFID 9G4260

UserManual.wiki >

Carestream Health >

4901 User Manual >

Carestream DV CHROMA User's Guide-ST CONFIDENTIAL

Contents

1. Carestream DV CHROMA Manual-ST CONFIDENTIAL
2. Carestream DV CHROMA User's Guide-ST CONFIDENTIAL

Carestream DV CHROMA User's Guide-ST CONFIDENTIAL

DRYVIEW CHROMA Imaging SystemUser’s GuideFor Trade Trial Use OnlyH210_0843ACSHORT TERM CONFIDENTIAL

Carestream Health, Inc.150 Verona StreetRochester, New York 14608United States© Carestream Health, Inc., 2012Printed in China.CARESTREAM, CHROMA, and DRYVIEW are trademarks of Carestream Health, Inc.Pub No. 9G4260_enRev. CSHORT TERM CONFIDENTIAL

iTable of ContentsOverview DRYVIEW CHROMA Imager at your Site............................................................................................................1-1Intended Use....................................................................................................................................................1-1Imager Features ...............................................................................................................................................1-2CHROMA Media .........................................................................................................................................1-2Network Interfaces.....................................................................................................................................1-2Power Management Features......................................................................................................................1-3Configuring and Monitoring the System (using the Web Portal) .................................................................1-3Enhancing Serviceability with Remote Monitoring ......................................................................................1-3How the Imaging System Works .......................................................................................................................1-4System Components .........................................................................................................................................1-4DICOM Interface ........................................................................................................................................1-4Imager .......................................................................................................................................................1-5Back View ..................................................................................................................................................1-7Control Panel .............................................................................................................................................1-8Display Screen .........................................................................................................................................1-10Using the Web Portal to Access Additional Functionality .................................................................................1-12Accessing the Web Portal .........................................................................................................................1-12Agency Compliance ........................................................................................................................................1-13Reference Information ...................................................................................................................................1-13User Guide Conventions .................................................................................................................................1-13Working with the Media and Ink Handling the CHROMA Media (Film or Paper).................................................................................................2-1Working with the Loaded Media.................................................................................................................2-2Understanding How Media is Selected for Print Requests .................................................................................2-3Loading the Media Cassette (Cut Sheets) ..........................................................................................................2-4Loading the Roll Paper.....................................................................................................................................2-9Placing the Roll Paper on the Spindle.........................................................................................................2-9Loading the Roll Paper into the Imager ......................................................................................................2-9Readying the Imager to Print to Roll Paper...............................................................................................2-10Cutting the Roll Paper ..............................................................................................................................2-11Changing the Media in the Imager..................................................................................................................2-12Handling a Print Request with a Different Requested Media .....................................................................2-12Handling a Media Change when the New Print Request is Urgent..............................................................2-13SHORT TERM CONFIDENTIAL

iiReplacing the Cut Sheet Media ................................................................................................................. 2-14Replacing the Roll Paper.......................................................................................................................... 2-16Working with Ink........................................................................................................................................... 2-19Extending the Life of Ink Cartridges During Periods of Inactivity or Low Use............................................ 2-19Checking Ink Levels ................................................................................................................................. 2-20Replacing Ink Cartridges.......................................................................................................................... 2-21Checking Maintenance Tank Levels.......................................................................................................... 2-23Replacing the Maintenance Tanks............................................................................................................ 2-24System Settings and Status Changing the Imager’s Date and Time.............................................................................................................. 3-1Changing Configuration Items in Maintenance Mode........................................................................................ 3-1Working in Maintenance Mode .................................................................................................................. 3-1Imager Language ....................................................................................................................................... 3-1Units of Measurement ................................................................................................................................ 3-2Temperature Units ..................................................................................................................................... 3-2Auto Cleaning............................................................................................................................................. 3-2Alert Settings.............................................................................................................................................. 3-2Number of Minutes Before Automatic Sleep Mode ..................................................................................... 3-3Return Settings to the Defaults ................................................................................................................... 3-3Checking Imager Status.................................................................................................................................... 3-4Print a Status Sheet .................................................................................................................................... 3-4View Imager Status..................................................................................................................................... 3-4Setting up Automatic Nozzle Check................................................................................................................... 3-5Setting up Roll Paper Settings........................................................................................................................... 3-6Media Selection ......................................................................................................................................... 3-6Roll Paper Margins .................................................................................................................................... 3-6Paper Size Check .......................................................................................................................................3-6Paper Skew Check ..................................................................................................................................... 3-6Set Roll Paper Tension............................................................................................................................... 3-6Optimizing the Look of the Image .................................................................................................................... 3-7Optimizing Grayscale Images on Film......................................................................................................... 3-7Optimizing Color Images on Paper............................................................................................................. 3-8Optimizing Grayscale Images on Paper ...................................................................................................... 3-8Maintenance and Troubleshooting Overview.......................................................................................................................................................... 4-1Preventing Issues by Keeping the Imager Clean ................................................................................................ 4-2Clean the Outside.......................................................................................................................................4-2Uneven Prints: Clean the Cassette Printing Path .......................................................................................... 4-2“Dirty” Prints: Clean the Inside .................................................................................................................. 4-3SHORT TERM CONFIDENTIAL

iiiWhite Powder on the Platen: Clean the Platen............................................................................................ 4-4Smudged Prints from the Roller................................................................................................................. 4-4Running a Nozzle Check to Avoid or Correct Print Issues................................................................................. 4-5Checking and Cleaning the Nozzles............................................................................................................ 4-5Working with the Print Head...................................................................................................................... 4-6Correcting Paper Cutting Problems.................................................................................................................. 4-8Correcting Errors .......................................................................................................................................... 4-12Introduction ............................................................................................................................................ 4-12Messages at the Imager Display Screen and Suggested Actions ................................................................ 4-12Roll Paper Errors .................................................................................................................................... 4-16Maintenance or Service Call is Required.................................................................................................. 4-17Troubleshooting ............................................................................................................................................ 4-18Imager is Not Printing.............................................................................................................................. 4-18Imager Sounds Like it is Printing, but Nothing Prints............................................................................... 4-18Prints Do Not Look as Expected............................................................................................................... 4-19Top Line of the DICOM Interface Screen is Blank .................................................................................... 4-20Feeding or Ejecting Problems/Media Jams............................................................................................... 4-21Clearing a Roll Paper Jam........................................................................................................................ 4-24An Icon on my Print Indicates a Sizing Issue, or some of the Image or Information is Cut Off.................. 4-25Miscellaneous Issues............................................................................................................................... 4-26Restarting the Imager .................................................................................................................................... 4-26The DICOM Interface is Non-Responsive (How to Restart) ............................................................................ 4-27Restoring the System Software—Ghosting..................................................................................................... 4-27Calling for Support ........................................................................................................................................ 4-29Specifications Dimensions and Clearance .............................................................................................................................. 5-1Packed Dimensions ......................................................................................................................................... 5-2Environmental Recommendations ................................................................................................................... 5-2Temperature.............................................................................................................................................. 5-2Relative Humidity....................................................................................................................................... 5-2Surface Levelness....................................................................................................................................... 5-2Acoustical Noise ........................................................................................................................................ 5-2Power Requirements ....................................................................................................................................... 5-2Network Requirements .................................................................................................................................... 5-2Ink Cartridges.................................................................................................................................................. 5-3Cartridge Life............................................................................................................................................. 5-3Temperature.............................................................................................................................................. 5-3Capacity..................................................................................................................................................... 5-3Weight....................................................................................................................................................... 5-3SHORT TERM CONFIDENTIAL

ivMedia .............................................................................................................................................................. 5-3Environmental ........................................................................................................................................... 5-3Storage ...................................................................................................................................................... 5-3Publication History .......................................................................................................................................... 5-4SHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-11OverviewDRYVIEW CHROMA Imager at your SiteThe DRYVIEW CHROMA Imaging System produces high-quality color and grayscale images on film and paper. Use the prints from this versatile system for diagnostic or referral purposes: • Print on DRYVIEW CHROMA Medical Film to produce diagnostic or referral images.• Print on DRYVIEW CHROMA Matte and Glossy Papers to produce images for referral, sharing, or educational purposes.The imager receives and prints from image sources such as medical electrical equipment (modalities) and workstations over the network. You can send print jobs simultaneously from multiple image sources. The open design lets you connect to modalities of all types and vendors.The imager provides the latest generation of pigment ink technology. Utilizing 11 ink colors, the imager produces a wide color gamut and supports up to 43 cm (17 in.) wide media. The supported film and papers provide consistent quality and resist fading and fingerprints, making the prints durable and long-lasting.IMPORTANT: Install the imager in a secure location to protect patient privacy rights if required by local regulations.Intended UseThe DRYVIEW CHROMA Imaging System is intended to provide hard copy images from digital imaging source output signals. The device is intended for use with DRYVIEW CHROMA film and reflective media (DRYVIEW CHROMA Medical Film and DRYVIEW CHROMA Medical Paper). The printer will interface with a variety of digital modalities, including, but not limited to, CR (Computed Radiology), DR (Digital Radiology), CT (Computerized Tomography), MRI (Magnetic Resonance Imaging). The images are to be used for medical diagnosis and referral to physicians and their patients. The DRYVIEW CHROMA Imaging System is not intended for use with FFDM or CR Mammography systems.Additionally, for the media:• DRYVIEW CHROMA Medical Papers and DRYVIEW CHROMA Medical Film are intended to be used in the DRYVIEW CHROMA Imaging System.• DRYVIEW CHROMA Medical Film is used to visualize selected parts of the human body, to determine whether they are normal or SHORT TERM CONFIDENTIAL

1-2 9G4260_en 2012-01-27Overviewpathologic. It is used by highly trained specialists, such as medical physicians or radiologic technologists working in diagnostic imaging. This film is intended for diagnostic or referral purposes.• DRYVIEW CHROMA Medical Paper, DRYVIEW CHROMA Medical Paper—Matte/Roll, and DRYVIEW CHROMA Medical Paper—Glossy/Roll, are intended to be used for referral only. These media types are not to be used for diagnostic purposes.Imager FeaturesCHROMA Media The imager is a wide-format ink jet color printer that supports DRYVIEW CHROMA Medical Film and DRYVIEW CHROMA Medical Paper (media). The CHROMA roll paper, media sheets, and media carriers are specially designed for the CHROMA imager. You must keep the cut media in the original carrier when you load it into the imager cassette.CHROMA media is available in the following sizes and types:• 20 x 25 cm (8 x 10 in.) blue base film• 25 x 30 cm (10 x 12 in.) blue base film• 28 x 35 cm (11 x 14 in.) blue base film• 35 x 43 cm (14 x 17 in.) blue base film• 22.0 x 28.0 cm (8.5 x 11.0 in.) matte paper and glossy paper• A3 (297.00 x 420.00 mm or 11.69 x 16.54 in.) matte and glossy paper• A4 (210.00 x 297.00 mm or 8.27 x 11.69 in.) matte and glossy paper• 297 mm x 100 m matte roll paper• 11 in. x 100 m matte roll paper• 297 mm x 75 m glossy roll paper• 11 in. x 75 m glossy roll paperFor more information about the media, see “Chapter 2 Working with the Media and Ink”.Network Interfaces The DICOM interface supports standard Ethernet network interfaces 1000Base-T, 100Base-TX, and 10Base-T.Media carrier for cut sheetsCHROMA mediaRoll paperSHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-3Power Management FeaturesTo reduce power consumption, the imager supports sleep mode. When no print jobs are in progress, the imager enters sleep mode. The default setting is 15 minutes; the imager enters sleep mode after 15 minutes of no activity. To change the number of minutes, see “Number of Minutes Before Automatic Sleep Mode” on page 3-3.Configuring and Monitoring the System (using the Web Portal)The Web Portal is your interface to more features. In addition to the installation and setup of your system, you can view and manage the imager's connections over the network, configure features, view error messages, and access general status information at the Web Portal. You can also check media count, size, and type.For more information, see “Accessing the Web Portal” on page 1-12.Enhancing Serviceability with Remote MonitoringCARESTREAM Remote Management Services is set up through the Web Portal, and is designed to enhance efficient system serviceability and simplify analytical and service processes through the monitoring of your equipment. Additionally, this simplifies the service process by providing qualified service personnel with faster, easier, and more complete access to the operational history of each system.Remote Management Services provides the following for the imager:• Ability to monitor and diagnose error conditions without introducing “downtime”• Firewall-safe, Internet transmission of machine data, while complying with patient confidentiality regulations• Minimal effort to set up communication• Flexibility to facilitate specific configurations at each siteSHORT TERM CONFIDENTIAL

1-4 9G4260_en 2012-01-27OverviewHow the Imaging System WorksThe imaging system consists of a DICOM interface (a small computer) and a printer (imager), connected together with a USB cable. The DICOM interface receives, processes, and manages the images, and the imager holds the media (film or paper) and ink and prints the images. The DICOM interface has hard-disk storage to hold a large number of digital images. As images are received for printing, they are stored, placed in a sequential print queue, and printed in order. The system can continue to accept incoming print jobs even if temporarily unable to print (for example, the media cassette is empty).During normal operation, the imager requires very little attention. It prints automatically in response to print requests from the configured image sources. Information sent with the images by the image source, such as media type and size and image quality settings, is applied unless you set the imager to override information that comes from the image source.System ComponentsDICOM Interface The DICOM interface brings the images over the network and formats them. It applies the processing parameters for optimal image quality and sends the images to the imager. The small screen at the front of the DICOM interface displays the installed media size and the requested media size (if different). It also displays a counter that tracks the approximate amount of loaded media that remains. For more information, see “Working with the Loaded Media” on page 2-2.For instructions to restart the DICOM interface, see “The DICOM Interface is Non-Responsive (How to Restart)” on page 4-27.ImagerDICOM interfaceSHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-5Imager1Front cover. Closes over the built-in cutter. 2Cartridge cover (left). Covers ink cartridges #1–6. See “Replacing the Ink Cartridges” on page 2-21.3Media cassette. Houses the cut sheet media in the media carrier. See “Loading the Media Cassette (Cut Sheets)” on page 2-4.4Output tray. Collects the ejected paper and film. Extend the tray according to the size of the media that is being ejected. 5Maintenance tank. Collects the waste ink for borderless printing. (Borderless printing is not supported with this imager release.)NOTE: In the software, this is referred to as “Maintenance Box 2."6Media eject support. Supports the ejected (printed) media. 7Cartridge cover (right). Covers ink cartridges #7–11 and the ink maintenance tank. To replace ink or maintenance tank, see “Working with Ink” on page 2-19.SHORT TERM CONFIDENTIAL

1-6 9G4260_en 2012-01-27Overview8Ink maintenance tank. Collects the waste ink.NOTE: In the software, this is referred to as “Maintenance Box 1."9Ink cartridges. Install a total of 11 ink cartridges on the left and right sides. To replace ink, see “Replacing the Ink Cartridges” on page 2-21.10 Print head. Fires ink via high-density nozzles while moving left and right. Do not move the print head by hand.11 Control panel. See “Control Panel” on page 1-8.12 Alert lamp. Alerts you with light when an error or warning occurs.• On—An error occurred. Check the error on the display screen.• Flashing—Ink or media is low. You can specify if the warning occurs for the media or the ink. The default is Off (no warning). • Off—No error.You can specify when the lamp alerts you. See “Alert Settings” on page 3-2.13 Top cover. Covers the inside of the imager.14 Media support. Supports the media that is fed manually. (Manual feed is not supported with this imager release.) 15 Manual edge guides. Guides the media that is fed manually. (Manual feed is not supported with this imager release.)16 Roller paper feeder. Receives the roll paper in the feeder slot. See “Loading the Roll Paper into the Imager” on page 2-9.17 Roll paper cover. Covers the roll paper. Leave the cover closed except when loading or removing the roll paper. See “Loading the Roll Paper into the Imager” on page 2-9.18 Spindle holder. Supports the left side of the roll paper spindle. See “Loading the Roll Paper” on page 2-9.SHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-7Back View1Rear access panel (covers the rear unit). Allows access to clear media jams. See “Feeding or Ejecting Problems/Media Jams” on page 4-21.2Roll paper holder unit connector. Always leave the cable connected.3USB connector. Connects the USB cable to the DICOM interface.4Airflow vents. Vents the air that cools the inside of the imager.5LAN connector. Not supported. The network is connected at the DICOM interface.6AC inlet. Connects the power cable.7Movable flange (black). Fixes the roll paper placed on the spindle. Remove and install when loading or removing the roll paper on the spindle. See “Placing the Roll Paper on the Spindle” on page 2-9.8Spindle. Holds the roll paper. To load roll paper into the imager, place the roll paper on the spindle. The gray flange on the right side is fixed on the spindle.9Attachment. Leave the attachment installed on the spindle.SHORT TERM CONFIDENTIAL

1-8 9G4260_en 2012-01-27OverviewControl Panel1Power light. Indicates the operational status.• On—Power is on.• Flashing—Receiving data or performing processes such as shutting off the power, head cleaning, or auto nozzle check.• Off—Power is off.2Power button. Powers the imager on or off. To shut down the imager, press the Power button. See “Restarting the Imager” on page 4-26.3Display screen. Displays the imager status, menus, and error messages. See “Display Screen” on page 1-10.4Ink Menu button. Provides access to the Ink Menu when the imager is in Ready status. From the Ink Menu, you can initiate a print head cleaning or a nozzle check.5 Media Source button. Lets you change between cut sheets and roll paper at the Paper Type Menu. See “Display Screen” on page 1-10.Press while the imager is in Ready status to display the Paper Type Menu.When any menu displays, press to return to the previous screen.1234567891011121314SHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-96Up/down or Media Feed buttons. • When roll paper is loaded: – Feed up to 3 m of paper by holding the button.– Increase the paper feed rate by holding for at least two seconds.– Press to rewind up to 20 cm of the roll paper. • If roll paper is not loaded, press to feed media from the cassette and to eject it from the imager. • When any menu displays, press an arrow button to navigate through the menu.7Menu button. • Press in the Ready status (or when no media is loaded) to display the menu. • Press when printing to display the Printer Status Menu.• When a menu displays, press the Menu button to access the next screen.8Paper Cut button. Press to cut the roll paper with the built-in cutter. NOTE: This feature is not necessary because the CHROMA Imager always cuts the roll paper automatically at the end of a print.9OK button.• Press when an item is selected from a menu to execute the item.10 Paper release light and button. • When pressed after roll paper printing is complete, the paper presser becomes unlocked, and the roll paper winds up to be removed. • Press to lock or unlock the paper presser. 11 Pause/Reset button.• Press to pause a print job. To restart printing, press again, or select Pause Cancel on the screen and then press OK. NOTE: To cancel print jobs in process, select Job Cancel on the screen and then press OK.• Press while the menu displays to return to Ready status.12 Pause/Reset light. Indicates if the imager is ready to print.• On—Not ready to print. The job is paused or canceled.• Off—Ready to print.SHORT TERM CONFIDENTIAL

1-10 9G4260_en 2012-01-27OverviewDisplay Screen13 Ink alert light. Indicates the ink status.• On—Indicates errors such as an empty ink cartridge. Check the error on the display screen. See “Correcting Errors” on page 4-12.• Flashing—The ink is low. Replace the cartridge to avoid the ink cartridge becoming empty while printing. See “Working with Ink” on page 2-19.• Off—No error.14 Media alert light. Indicates the status of the media. • On—No media is loaded or the paper setting is not correct. Check the error on the display screen. See “Correcting Errors” on page 4-12 for help.• Flashing—Indicates errors such as media jam or skew. Check the error on the display screen. See “Correcting Errors” on page 4-12 for help.• Off—No error.1Message. Displays status, operational, and error messages.2Media source setting. Indicates the media source. IMPORTANT: If you will use roll paper, it is only necessary to change the media source initially to Roll Paper/Cut. After you have enabled the imager to print to roll paper, you can leave the media source setting at Roll Paper/Cut. Prints on roll paper and cuts automatically after printing each page. This setting supports printing to both roll paper and the media cassette.Prints on roll paper but does not automatically cut after printing.NOTE: This setting is not used because the CHROMA Imager always cuts the roll paper automatically.123546SHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-11Prints from the media cassette only. 3Ink cartridge status. Displays the approximate level of remaining ink in the cartridge. The icons change when the ink is low or an error occurs. See “Checking the Ink Levels” on page 2-20 for more information.4Black ink. Displays the type of black ink that the imager is using. The imager automatically uses the optimal black ink type for the installed media.NOTE: The imager uses either Matte or Photo Black ink to provide the best quality for the requested print job. Photo Black ink provides a smooth finish for glossy paper, while Matte Black ink increases black optical density for matte paper. 5Maintenance tank status. Displays the status for the maintenance tanks. See “Checking the Maintenance Tank Levels” on page 2-23 for more information.6Roll paper margin parameter. The margin settings display after the icon. The margin parameter is set to 3 mm during installation, and other margin parameters are not supported. SHORT TERM CONFIDENTIAL

1-12 9G4260_en 2012-01-27OverviewUsing the Web Portal to Access Additional FunctionalityThe Web Portal is your interface to additional features. In addition to the installation and setup of your system, you can view and manage the imager's connections over the network, configure features, view error messages, and access general status information at the Web Portal. You can also check media count, size, and type.Troubleshooting tools include:• Optimization of image quality for modalities.• Retrieval of logs, statistics, and system status.• Diagnostic utilities, including backup and restore.The Web Portal provides an online Help system and a user’s guide to assist you.Accessing the Web PortalTo access the Web Portal, use a desktop or laptop computer that is connected to the network. 1. On a desktop or laptop computer, start WINDOWS INTERNET EXPLORER.2. In the address field, type: http://<the imager IP address>.NOTE: The IP address should be written on the back of the Quick Reference Guide. If you cannot locate the IP address, check with your network administrator or the person who installed the imager. 3. Click Go.The main window for the Web Portal shows the general status, the number of print jobs queued, the number of jobs waiting for media, and the media count.The center panel displays the screens where you view and perform tasks. The user’s guide for the Web Portal procedures is available by selecting Documentation from the left panel, and the Help icon provides context-sensitive Help for fields and pages. The left panel also provides the links to all other screens.Left panel to navigate to other areas of the Web PortalView status, etc.SHORT TERM CONFIDENTIAL

Overview2012-01-27 9G4260_en 1-13Agency ComplianceSee the Safety Manual, 9G4259.Reference InformationThe following documentation and information might be useful as you use and support the CHROMA Imaging System.• DICOM Conformance Statement—Go to http://www.carestream.com/dicom.html• CHROMA on the Web—Go to http://www.carestream.com/med-printing.html• CHROMA online registration—Go to http://www.carestream.com/chroma-registration.html• Web Portal procedures, 9G7572—Access the Web Portal, and then click the Documentation link• Quick Reference Guide, 9G6534—See the most commonly used CHROMA features at a glance• Safety Manual, 9G4259—Access information about safety and standards compliance• Media Requirements, 9G8448—Learn how to handle the CHROMA mediaUser Guide ConventionsThe following special messages emphasize information or indicate potential risks to personnel or equipment.NOTE: Notes provide additional information, such as expanded explanations, hints, or reminders.IMPORTANT: Important notes highlight critical policy information that affects how you use this guide and this product.CAUTION:Cautions point out procedures that you must follow precisely to avoid damage to the system or any of its components, loss of data, or corruption of files in software applications.DANGER: DANGER IDENTIFIES PROCEDURES THAT YOU MUST FOLLOW PRECISELY TO AVOID INJURY TO YOURSELF OR OTHERS.SHORT TERM CONFIDENTIAL

SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-12Working with the Media and InkHandling the CHROMA Media (Film or Paper)When working with media:• Avoid touching the printable surface with your bare hands. Fingerprints might affect print quality. Handle the media by its edges.• For optimal performance, allow the media to dry thoroughly. Media drying time may vary depending on environmental conditions.• Avoid exposure to moisture and adhesives.• Do not place sticky notes on the media. Removal of a sticky note could damage the printed image.• Before storing printed media, let the media thoroughly dry. • Remove prints promptly after printing due to limited space in the output tray.NOTE: If disposing of used media, manage the disposal appropriately to protect patient privacy rights, if required by local regulations.SHORT TERM CONFIDENTIAL

2-2 9G4260_en 2012-01-27Working with the Media and InkWorking with the Loaded MediaViewing the Loaded Media SizeThe DICOM interface screen displays the loaded media size by dimension, for example, “8.5 x 11” or “A4.” The dimensions are represented in inches with the exception of “A3” and “A4.”Monitoring the Amount of Loaded MediaThe DICOM interface screen displays a gauge to help you monitor the amount of loaded media that remains in the media carrier or on the roll.A full carrier or roll is represented by the following:[ * * * * * ]The asterisks decrease as the carrier or roll is emptied. This example shows a nearly empty carrier or roll:[* ]Checking the DICOM Interface for the Requested Media SizeIf a print request has arrived at the imager with a different media size than the loaded media, the new size appears on the DICOM interface screen to alert you to install the requested size. The DICOM interface screen displays the loaded size on the top row and the requested size on the lower row. For example:See “Changing the Media in the Imager” on page 2-12 for instructions to change the loaded media.Output tray and media cassetteThe DICOM interface screen displays information about the loaded and requested mediaRoll feeder and roll paper11 x 14 [*** ]A3The loaded media size is 11 x 14 in.The requested media size is A3. You must unload the 11 x 14 in. media and then load A3 media to let the job print.SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-3Understanding How Media is Selected for Print RequestsYour imager can print to both the media cassette and the roll feeder. The imager automatically selects the media source based on the media type (film or paper) and size of the job request, for example:• A job request with film specified at the modality will only go to the media cassette (because film can only be loaded in the media cassette).– If the job request matches the loaded film size, the job prints.– If the job request matches a supported film size but that size is not loaded in the cassette, the DICOM interface alerts you that a different media size is requested. You must load the requested film size in the media casette so the job can print.– If the job request does not match a supported film size, then the imager prints to (or requests) the supported film size that is closest to and larger than the job request.• A job request with paper specified at the modality will only print to paper. If paper is loaded in the media cassette and in the roll feeder, then the imager uses the image size to determine the media source:– If the job request matches a size that is already loaded in the media cassette or can be printed on the roll paper (22.0 x 28.0 cm / 8.5 x 11.0 in., A3, or A4), then the job goes to the matching media.– If the job request matches a size that is loaded in the media cassette and can be printed on roll paper (when either A3 or A4 paper is loaded in the media cassette), then the job goes to the roll paper.– If the job request does not match a supported paper size, then the imager prints to (or requests) the supported paper size that is closest to and larger than the job request. For example, a request to print on 8.0 x 10.0 in. paper would print on 8.5 x 11.0 in. paper.SHORT TERM CONFIDENTIAL

2-4 9G4260_en 2012-01-27Working with the Media and InkLoading the Media Cassette (Cut Sheets)IMPORTANT: Do not remove or insert the cassette from the imager while printing. It may cause the print quality to decline or cause a jam. If you do remove the cassette while printing, wait until printing is complete to reinsert it. IMPORTANT: Always leave the media in the carrier when you load it into and unload it from the cassette. Store the unused media in its carrier and in the original carton.IMPORTANT: Always remove the output tray and the cassette from the imager to load or remove media. Sliding the media carrier into the cassette without fully removing the tray from the imager can cause issues with the media.1. Lift the edge of the output tray to remove it.2. Slide open the media cassette, lift it slightly, and pull it out.IMPORTANT: Be careful not to drop the media! The media must remain in the carrier and in the original orientation, with the same side facing up. Do not remove or lose any sheets from the media carrier. If any sheets are removed, the imager cannot accurately track the media count.3. Open the new media package, and fan the open end. Leave the media in the carrier when you fan it.Media carrierCarestreamH210_0617ACSHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-54. If necessary, expand the edge guides to make space for the media before you place the media into the cassette.5. Carefully place the media, with the carrier, into the media cassette.IMPORTANT: Keep the media carton. If you change the media size in the imager later, place the media back in the original carton.6. Adjust the edge guides around the media carrier. Move the guide without moving the slider.Open the edge guides to make space for the mediaSHORT TERM CONFIDENTIAL

2-6 9G4260_en 2012-01-27Working with the Media and Ink7. Insert the cassette and push it firmly into the imager.8. Replace the output tray.9. Extend the output tray for the media size and raise the flap. Adjust the output tray depending on the size of the media loaded in the cassette:• A4: Slide out the third extension of the output tray, raise the flap, and then push the section back in.SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-7• A3: Pull out the third section of the output tray, and then raise the flap.SHORT TERM CONFIDENTIAL

2-8 9G4260_en 2012-01-27Working with the Media and Ink10. Check that the imager is on.11. If you will print:•Only to the media cassette, check that the Media Source setting is set to Cut Sheet.• To both media cassette and roll paper, check that the Media Source setting is set to Roll Paper/Cut.NOTE: The Roll Paper/Cut setting supports printing to both roll paper and to cut sheets in the media cassette. To change the Media Source setting:• Press to display the Paper Type Menu.• Press to select Roll Paper/Cut or Cut Sheet.•Press OK. Roll Paper/CutCut SheetSHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-9Loading the Roll PaperPlacing the Roll Paper on the SpindleNOTE: If the roll paper is already loaded on the spindle, go to “Loading the Roll Paper into the Imager” on page 2-9.1. Remove the black flange from the spindle. 2. To insert the spindle into the roll paper, place the roll paper on a flat surface where the end of the roll paper is hanging down toward you, and insert the spindle from the right.3. Install the black flange on the end of the spindle. Push until there are no gaps between the roll paper core and the flange.Loading the Roll Paper into the Imager1. Open the roll paper cover.2. Hold the roll and paper with the black flange on the left and the gray flange on the right. Holding the flanges, tilt the spindle up on the right side at a 45 ° angle (A). Slide the left side of the spindle into the hole of the spindle holder so the spindle rests on the holder (B). Then place the right side of the spindle straight down into the imager (C). Black flange Gray flange (fixed)SpindleRoll paperRoll paper coverH210_0851BABlack flangeBCSpindle holderASHORT TERM CONFIDENTIAL

2-10 9G4260_en 2012-01-27Working with the Media and InkNOTE: If the spindle is set in the wrong direction, the paper will not feed correctly.3. Remove the protective wrap from around the roll paper.4. Press on the control panel.5. Insert the leading edge of the roll paper into the slot. Make sure the edge is not folded, and remove any slack from the paper.• When Auto Roll Feeding is On (default)—Insert the roll paper slightly into the feeder slot, and watch the display screen. • When Auto Roll Feeding is Off—Insert the paper so the edge of the paper comes out of the front manual feeder, and watch the display screen.6. When the display screen changes to: Press the button, press to automatically feed the paper to the start position.7. Close the roll paper cover.Readying the Imager to Print to Roll Paper1. The screen displays Are these settings OK? • Select No, and then press OK.• When the Paper Type Menu appears, use the arrow buttons to select No Paper Selected.• Select OK.NOTE: Remove prints promptly after printing due to limited space in the output tray.Feeder slotSHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-112. Slide the output tray to the second and third extensions.NOTE: Do not raise the flap. If the flap is raised while printing from the roll feeder (for example, if No Cut is selected), the paper might eject incorrectly.3. Set up the paper eject support depending on the paper type.4. Check that the Media Source setting is set to Roll Paper/Cut.NOTE: The Roll Paper/Cut setting supports printing to both roll paper and to cut sheets in the media cassette. To change the Media Source setting:• Press to display the Paper Type Menu.• Press to select Roll Paper/Cut.• Press OK. Cutting the Roll Paper After printing, the paper is cut automatically.NOTE: If the roll paper cannot be cut by the built-in cutter, press to feed the paper to a position where you can cut it manually.Roll Paper/CutSHORT TERM CONFIDENTIAL

2-12 9G4260_en 2012-01-27Working with the Media and InkChanging the Media in the ImagerHandling a Print Request with a Different Requested MediaIf a print job requires a different media from the media that is currently loaded in the imager, the new size appears on the DICOM interface screen to alert you to install the requested size. See “Understanding How Media is Selected for Print Requests” on page 2-3 for more information about image sizes and requested media sizes.The DICOM interface screen displays the loaded size on the top row and the requested size on the lower row. For example:In this example, the 28 x 35 cm (11 x 14 in.) media is loaded, but a print job has arrived at the CHROMA imager requesting A3 media. If there are current jobs to print on the loaded media...If there are no current jobs for the loaded media...1. Wait until the current jobs finish printing.2. Replace the loaded media with the requested media. See “Replacing the Cut Sheet Media” on page 2-14 or “Replacing the Roll Paper” on page 2-16.The DICOM interface senses the change; the DICOM interface screen changes, and the new job automatically prints.Replace the loaded media with the requested media. See “Replacing the Cut Sheet Media” on page 2-14 or “Replacing the Roll Paper” on page 2-16.The DICOM interface senses the change; the DICOM interface screen changes, and the new job automatically prints.11 x 14 [*** ]A3Represents the amount of the loaded media remainingThe loaded media size is 28 x 35 cm (11 x 14 in.)The requested mediasize is A3SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-13Handling a Media Change when the New Print Request is UrgentIf a print job requires a different media size from the loaded media, but several current jobs are processing with the loaded media and you cannot wait for the current jobs to complete printing, you can stop the jobs in progress to print your urgent job.1. Access the Web Portal. See “Using the Web Portal to Access Additional Functionality” on page 1-12.2. In the Web Portal, click Monitoring and Control > Imager Monitor.3. Next to Delivery Output Online, click Change Subsystem Status. All the current print jobs will stop, and printer status changes to “Printing Disabled.” 4. Replace the loaded media with the requested media (for the urgent print request). See “Replacing the Cut Sheet Media” on page 2-14 or “Replacing the Roll Paper” on page 2-16.5. Send the urgent print request from the modality.6. Return to the Web Portal, and click Monitoring and Control > Imager Monitor.7. Next to Delivery Output Online, click Change Subsystem Status again. The printer status changes to “Printing,” and the urgent job prints.8. To print the jobs that you stopped, replace the urgent job’s media with the requested media for the earlier jobs. See “Replacing the Cut Sheet Media” on page 2-14 or “Replacing the Roll Paper” on page 2-16. The earlier jobs will automatically start printing.SHORT TERM CONFIDENTIAL

2-14 9G4260_en 2012-01-27Working with the Media and InkReplacing the Cut Sheet Media1. Retrieve the new media.IMPORTANT: Be careful not to drop the media! The media must remain in the carrier and in the original orientation, with the same side facing up. Do not remove or lose any sheets from the media carrier. If any sheets are removed, the imager cannot accurately track the media count.IMPORTANT: Always leave the media in the carrier when you load it into and unload it from the cassette. Store the unused media in its carrier and in the original carton.2. Lift the edge of the output tray to remove it.IMPORTANT: Always remove the output tray and the cassette from the imager to load or remove media. Sliding the media carrier into the cassette without fully removing the tray from the imager can cause issues with the media.3. Slide open the media cassette, lift it slightly, and pull it out.4. Remove the media, with the carrier, from the media cassette. Open the edge guides as necessary to remove the media and carrier.5. Carefully place the media and carrier in the original carton. Set it aside if you will use it again soon, or place it in storage with the appropriate environmental conditions (see “Environmental Recommendations” on page 5-2).SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-156. Open the new media package, and fan the open end. Leave the media in the carrier when you fan it.7. Expand the edge guides if necessary, and then carefully place the media, with the carrier, into the media cassette.IMPORTANT: Keep the media carton. If you change the media size in the imager later, place the media back in the original carton.8. To check that the new media size has been read by the imager, view the DICOM interface screen and confirm that the new media size appears in the top row. The system is ready, and the print request starts printing.CarestreamH210_0617ACSHORT TERM CONFIDENTIAL

2-16 9G4260_en 2012-01-27Working with the Media and InkReplacing the Roll Paper 1. Retrieve the new media.2. Open the roll paper cover.3. Press to release the paper presser. NOTE: Normally, the roll paper rewinds automatically after cutting. If the roll paper does not rewind, rotate the flanges in the opposite direction to rewind, and then press to release the paper presser. Check that the roll paper is rewound before attempting to remove the spindle.CAUTION:If the roll paper is not rewound, the spindle might be locked. You might damage the imager by trying to remove the spindle when it is locked. Always rewind the paper and then press to release the paper presser before removing the spindle.4. Lift up on the right side of the spindle from the gray flange to bring the spindle to a 45 ° angle (A). Pull the spindle up and to the right to remove it from the spindle holder.Roll paper coverH210_0852BAAGray flangeSHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-175. Remove the black flange from the spindle:• While holding the black flange as shown, push the end of the spindle to release the flange from the spindle.• If the flange does not come off easily, lightly tap the end of the spindle on the black flange side.• When removing a flange from the spindle while only the paper core is remaining, hold the core and push the spindle.CAUTION:Be careful to avoid tapping the right side of the spindle (the side with the gray flange) against a hard surface. You might damage the spindle by the impact.6. To insert the spindle into the new roll paper, place the roll paper on a flat surface where the end of the roll paper is hanging down toward you, and insert the spindle from the right.7. Install the black flange on the end of the spindle. Push until there are no gaps between the roll paper core and the flange.Black flangeBlack flange Gray flange (fixed)SHORT TERM CONFIDENTIAL

2-18 9G4260_en 2012-01-27Working with the Media and Ink8. Hold the roll and paper with the black flange on the left and the gray flange on the right. Holding the flanges, tilt the spindle up on the right side at a 45 ° angle (A). Slide the left side of the spindle into the hole of the spindle holder so the spindle rests on the holder (B). Then place the right side of the spindle straight down into the imager (C). NOTE: If the spindle is set in the wrong direction, the paper will not feed correctly.9. Remove the protective wrap from around the roll paper.10. Press .11. To check that the new media size has been read by the imager, view the DICOM interface screen and confirm that the new media size appears in the top row. The system is ready, and the print request starts printing.H210_0851BABlack flangeBCSpindle holderASHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-19Working with InkDANGER: IF INK GETS ON SKIN, WASH IT OFF WITH SOAP AND WATER. IF INK GETS IN EYES, FLUSH IMMEDIATELY WITH WATER.CAUTION:Do not dismantle ink cartridges or try to refill them. This could cause damage to the print head. Also, do not touch the ink supply port or its surrounding area or the green IC chip on the side of the ink cartridge.CAUTION:Use inks that are designed for this imager for optimal quality and reliability. The use of other products may affect your print quality and could result in damage to the imager.Store ink cartridges in a cool, dry place. See “Ink Cartridges” on page 5-3 for more information.NOTE: Dispose of the used ink cartridges carefully and in accordance with local ordinances.Extending the Life of Ink Cartridges During Periods of Inactivity or Low UseFor best printing results, use an ink cartridge within six months of opening the ink cartridge package.You can store partially used ink cartridges out of the imager for up to six months. If you do so, cover the opening (the ink supply port) with cellophane tape to prevent the ink from drying.To extend the life of the ink cartridges during periods of low or no activity, remove the ink cartridges from the imager and, without touching the green IC chip, gently shake the ink cartridges horizontally.Some ink cartridges are likely to be used more slowly than others. To extend the life of low-use ink cartridges, occasionally take the ink cartridges out of the imager and gently shake them horizontally, and then return them to the imager.Ink cartridgeDo not touch the ink supply port.Do not touch the green chip.SHORT TERM CONFIDENTIAL

2-20 9G4260_en 2012-01-27Working with the Media and InkChecking the Ink LevelsCheck the ink level at the display screen.1. Ink slot numbers—the location of the ink cartridge in the imager. 2. Ink levels—the approximate amount of remaining ink. NOTE: You can also view the ink levels at the Status Menu. See “Ink Levels” on page 3-4. Check the ink levels before printing a large job. If an ink cartridge is low, prepare a new cartridge.Ink slot numbers. When facing the imager, the slots are numbered from left to right in ascending order from 1:When the ink is low or empty, the icons on the display screen change:Ink cartridge status indicators. These appear on the ink icon when a status condition exists (ink low or error).Ink color codes. An additional indicator of the ink cartridge with the condition that must be addressed.121. GR (Green)2. LLK (Light Light Black)3. Y (Yellow)4. LC (Light Cyan)5. VLM (Vivid Light Magenta)6. OR (Orange)7. MK (Matte Black)8. VM (Vivid Magenta)9. LK (Light Gray)10. C (Cyan)11. PK (Photo Black)Ink slot numberStatus indicatorInk color codeInk is low. Prepare a new ink cartridge. See “Replacing the Ink Cartridges” on page 2-21.An error occurred. Check the message on the screen, and clear the error. See “Correcting Errors” on page 4-12 for help.SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-21Replacing the Ink CartridgesIf one of the ink cartridges is empty, printing will stop. If an ink-low warning displays, replace the ink cartridge(s) as soon as possible.This procedure uses Matte Black ink as an example. Follow the same steps to replace any ink cartridge.1. Check that the imager is on.2. Press the groove in the cartridge cover to open the cover.3. Push the empty ink cartridge into the imager until you hear a click. The ink cartridge pops out slightly.4. Carefully pull the cartridge straight out of the slot.NOTE: Removed ink cartridges may have ink around the ink supply port, so be careful not to get ink on the surrounding area when removing a cartridge. Dispose of the used ink cartridges in accordance with local ordinances.SHORT TERM CONFIDENTIAL

2-22 9G4260_en 2012-01-27Working with the Media and Ink5. Remove the replacement ink cartridge from the bag. Shake the ink cartridge horizontally for approximately 15 seconds.CAUTION:Do not touch the green IC chip on the ink cartridges. This can cause the imager to malfunction.6. Match the ink cartridge color with the color label on the back of the cartridge cover. Hold the ink cartridge with the arrow mark facing up. The cartridge label is upright and faces you. Insert the cartridge into the slot as far as it will go until it clicks. NOTE: When the cartridge is inserted, the label faces out toward you.7. Repeat the steps for each ink cartridge as needed.NOTE: Install an ink cartridge in each slot. You cannot print if any of the slots are empty.8. Close the cartridge cover.SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-23Checking the Maintenance Tank LevelsCheck the maintenance tank levels at the display screen.1. Maintenance tank 1—the main maintenance tank that collects waste ink while the system prints. To replace, see “Replacing the Ink Maintenance Tank (Tank 1)” on page 2-24.2. Maintenance tank 2 —the borderless maintenance tank. To replace, see “Replacing the Borderless Maintenance Tank (Tank 2)” on page 2-26.NOTE: Since maintenance tank 2 is used for borderless printing, it may not be necessary to replace it. (The CHROMA system does not support borderless printing.)NOTE: You can also view the maintenance tank levels at the Status Menu. See “Maintenance Tank Levels” on page 3-4. Check the level of maintenance tank 1 before doing a power cleaning. If the tank is almost full, prepare a new tank.When the maintenance tank is full or nearly full, the icons on the display screen change:12When flashing, the maintenance tank is almost full. Prepare a new maintenance tank. When flashing, the maintenance tank is full. Replace it with a new tank. See “Replacing the Maintenance Tanks” on page 2-24.SHORT TERM CONFIDENTIAL

2-24 9G4260_en 2012-01-27Working with the Media and InkReplacing the Maintenance TanksIf the message “Replace Maint Box” or “Not Enough Empty Space” appears at the display screen, replace the specified maintenance tank.IMPORTANT: Do not reuse a maintenance tank that has been removed from the imager and exposed to air for an extended period of time. The ink inside the exposed tank will dry, making the tank unable to absorb new ink.Replacing the Ink Maintenance Tank (Tank 1)NOTE: Do not replace the maintenance tank while printing. The waste ink may leak.1. Press the groove in the right cartridge cover to open it.2. Pull out the maintenance tank. 3. Lift the tank up to release the lock.4. Place the used tank in the plastic bag that is included with the new tank. SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-25NOTE: Dispose the used tank in accordance with local ordinances.5. Insert the new maintenance tank.IMPORTANT: Do not touch the green IC chip on the side of the maintenance tank. Do not remove the film from the top of the maintenance tank.6. Close the cartridge cover.SHORT TERM CONFIDENTIAL

2-26 9G4260_en 2012-01-27Working with the Media and InkReplacing the Borderless Maintenance Tank (Tank 2)IMPORTANT: Do not replace the maintenance tank while printing. Printing stops if the lock on the maintenance tank 2 is released. If stopped during printing, the colors may vary and/or the print quality may decline when printing is resumed.NOTE: Since maintenance tank 2 is used for borderless printing, it may not be necessary to replace it. (Borderless printing is not supported with this release.)1. To remove the output tray, lift the edge of the output tray slightly.2. Release the tank lock.SHORT TERM CONFIDENTIAL

Working with the Media and Ink2012-01-27 9G4260_en 2-273. Pull out the maintenance tank carefully so it does not tilt.DANGER: IF INK SPILLS ONTO YOUR SKIN OR INTO YOUR EYES, WASH THE AFFECTED AREA WITH WATER IMMEDIATELY.4. Place the used tank in the plastic bag that is included with the new tank. NOTE: Dispose of the used tank in accordance with local ordinances.NOTE: Do not tilt the tank until it is completely in the plastic bag and the zipper is closed. The waste ink might leak.5. Insert the new tank. Push it in firmly.IMPORTANT: Do not touch the green IC chip on the side of the maintenance tank. Do not remove the film from the top of the maintenance tank.SHORT TERM CONFIDENTIAL

2-28 9G4260_en 2012-01-27Working with the Media and Ink6. Set the lock.7. Replace the output tray.SHORT TERM CONFIDENTIAL

System Settings and Status2012-01-27 9G4260_en 3-13System Settings and StatusChanging the Imager’s Date and TimeNOTE: To change the date and time for the Web Portal, log on to the Web Portal, and then click the Documentation link for instructions. This procedure lets you change the date and time for the imager only.1. At the imager control panel, press .2. Press to select Maintenance, and then press .3. Press to select Clock Setting, and then press .4. Use the arrow buttons to set each item for the date and time, displayed in the format: MM/DD/YY HH:MM.5. Press OK.6. Press to exit.Changing Configuration Items in Maintenance ModeIn maintenance mode, you can set up configuration items such as the language and temperature units. These changes apply on the imager display screen, on some reports, and on test prints.Working in Maintenance ModeTo start the imager in maintenance mode:1. Shut down the imager. (Press the Power button on the imager control panel.)2. Press and hold . Continue to hold down the button, and at the same time, press and then release the Power button. When the Maintenance Mode Menu appears, release the button.3. Use the arrow buttons to change the settings. (See details in the procedures below). To return to the previous menu, press .4. When finished changing the settings, shut down the imager to exit from maintenance mode. NOTE: When you start the imager again, it will have exited from maintenance mode and will be ready to print.Imager Language NOTE: To change the language for the Web Portal, log on to the Web Portal, and then click the Documentation link for instructions. The procedure below changes the language for the imager display screen only.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.2. Make sure Language is selected, and then press .SHORT TERM CONFIDENTIAL

3-2 9G4260_en 2012-01-27System Settings and Status3. Press to select the language, and then press OK. NOTE: The language changes immediately, but you must shut down the imager to exit from maintenance mode.4. Press the Power button to shut down the imager, and then start the imager again. The display screen appears in the language you selected.Units of Measurement Select between metric or U.S. imperial to display, for example, the media size on reports and test prints at the imager.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.2. Press to select Length Units, and then press .3. Press to change between metric and feet/inch, and then press OK. 4. Shut down the imager, and then start it again.Temperature Units Select between Celsius (C) and Fahrenheit (F) to display, for example, on reports and test prints at the imager.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.2. Press to select Temperature Units, and then press .3. Press to change between C and F, and then press OK. 4. Shut down the imager, and then start it again.Auto Cleaning The imager automatically cleans the nozzles as needed, for example, if clogged nozzles are detected during a nozzle check.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.2. Press to select Auto Cleaning Times, and then press .3. Use the arrow buttons to change the value (1-3), and then press OK. 1 (default) = one auto cleaning, 2 = two auto cleanings, and 3 = three auto cleanings per session.4. Shut down the imager, and then start it again.Alert Settings If alert settings are enabled, the alert lamp flashes when the condition is met. For example, if you select Ink from the Maintenance Alert Menu, the lamp flashes when ink is low. If Ink is not selected, an Ink Low message will still appear on the display screen, but the alert lamp will not flash.NOTE: A flashing alert lamp is helpful because you can see it from across a room.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.SHORT TERM CONFIDENTIAL

System Settings and Status2012-01-27 9G4260_en 3-32. Press to select Maintenance Alert, and then press .3. Press to select an item, and then press OK. •Disable—The alert lamp is disabled.•Ink—The alert lamp flashes when ink is low or empty.•Maintenance Box—The alert lamp flashes when maintenance tank is full.•Ink or Maint Box—The alert lamp flashes when ink or maintenance tank is nearing replacement.•Papers—The alert lamp flashes when media is low or empty; set to Roll Paper Remaining or Cut Sheet Remaining.•All—The alert lamp flashes for ink, maintenance tank, and media (film and paper) warnings.4. Shut down the imager, and then start it again.Number of Minutes Before Automatic Sleep ModeTo reduce power consumption, the imager enters sleep mode after a configurable number of minutes without activity. When in sleep mode, the imager display screen goes dark. The imager becomes active again when it receives a print job. The default setting is 15 minutes.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.2. Press to select Sleep Mode, and then press .3. Press to select 5, 15 (default), 60, 120, or 180 minutes, and then press OK. 4. Shut down the imager, and then start it again.Return Settings to the DefaultsIMPORTANT: If you return to the default settings, you change some settings that are required for the CHROMA system to operate normally. It will be necessary to reconfigure some settings that you specified during the system installation. For that reason, this procedure is not recommended for CHROMA users.1. Enter maintenance mode. See “Working in Maintenance Mode” on page 3-1.2. Press to select Default Panel, and then press .3. With Execute selected, press OK. 4. Shut down the imager, and then start it again.SHORT TERM CONFIDENTIAL

3-4 9G4260_en 2012-01-27System Settings and StatusChecking Imager StatusPrint a status sheet or view various items on the imager screen. You can also check status at the Web Portal. See “Accessing the Web Portal” on page 1-12 for more information.Print a Status Sheet The status sheet shows settings such as auto nozzle check (on or off), the media status (how much is remaining), the maintenance tank status (how much space is remaining in the tank), and the IP address.1. Press .2. Press to select Test Print, and then press .3. Press to select Status Sheet, and then press .4. Press OK to start printing.View Imager Status This procedure displays the selected information on the imager display screen.1. Press .2. Press to select Printer Status, and then press .3. Select one of the procedures below.4. Press to exit the menu.Firmware Version From the Printer Status Menu, press . When done viewing the firmware version, press to exit.Ink Levels From the Printer Status Menu, press to select Ink Level, and then press . The percentage of ink remaining in the first ink cartridge displays. Continue pressing to see the status of the remaining cartridges. When done, press to exit.NOTE: You can also view the approximate ink levels at any time on the imager display screen. See “Checking the Ink Levels” on page 2-20.Maintenance Tank Levels From the Printer Status Menu, press to select Maintenance Box, then press . The percentage of ink absorption space remaining for each tank displays. As the tank fills, the percentage decreases. When done, press to exit.NOTE: You can also view the approximate maintenance tank levels at any time on the imager display screen. See “Checking the Maintenance Tank Levels” on page 2-23.SHORT TERM CONFIDENTIAL

System Settings and Status2012-01-27 9G4260_en 3-5Job History From the Printer Status Menu, press to select Job History, and then press . For the last 10 print jobs saved in the imager, the following displays: • Job no. (0-9), with 0 being the current job• Amount of ink used, in milliliters• Amount of media used, in square centimetersWhen done, press to exit.Total Print Count From the Printer Status Menu, press to select Total Prints, then press . When done, press to exit.Setting up Automatic Nozzle CheckYou can configure the imager to regularly check for nozzle clogs. If clogs are found, Auto Cleaning is initiated. 1. Press .2. Select Printer Setup, and then press .3. Press to select Auto Nozzle Check, and then press .4. Select one of the following, and then press OK:•On: Every Job—The imager checks the nozzles before every print job and runs a cleaning cycle if necessary.•On: Periodically (default)—The imager periodically checks the nozzles and runs a cleaning cycle if necessary. •Off—The imager does not perform automatic nozzle checks or cleaning cycles.When changing the black ink type, the imager always performs an Auto Nozzle Check.When a clog is detected, Auto Cleaning is performed for the number of times set in the Maintenance Mode Menu until the clogged nozzles are clear. (See “Auto Cleaning” on page 3-2.)SHORT TERM CONFIDENTIAL

3-6 9G4260_en 2012-01-27System Settings and StatusSetting up Roll Paper SettingsThese parameters are set up during the installation of the imager. Media Selection When the media source is set to Cut Sheet, the image only prints from the media cassette. When the media source is set to Roll Paper, the imager can print to both the media cassette and roll paper. Leave the media source set to Roll Paper/Cut to print from both media sources.Press the Media Source button to change between Cut Sheet and Roll Paper/Cut.Roll Paper Margins Only 3 mm is supported.1. Press . 2. Press to select Printer Setup, and then press .3. Press to select Roll Paper Margin, and then press to select 3 mm.4. Press OK.5. Press to return to the Ready screen.Paper Size Check Leave Paper Size Check set to On.1. Press . 2. Press to select Printer Setup, and then press .3. Press to view Paper Size Check. Confirm that the setting is On.4. Press OK.5. Press to return to the Ready screen.Paper Skew Check Leave Paper Skew Check set to On.1. Press . 2. Press to select Printer Setup, and then press .3. Press to view Paper Skew Check. Confirm that the setting is On.4. Press OK.5. Press to return to the Ready screen.Set Roll Paper Tension If wrinkles appear in the roll paper while printing, change the setting. 1. Press . 2. Press to select Paper Setup Menu, and then press .3. Press to select Set Roll Paper Tension.4. Press to select High or Extra High.5. Press OK.6. Press to return to the Ready screen.SHORT TERM CONFIDENTIAL

System Settings and Status2012-01-27 9G4260_en 3-7Optimizing the Look of the ImageYou can adjust the look of the printed images. To access these options, access the Web Portal (see “Accessing the Web Portal” on page 1-12).NOTE: In the Web Portal, the Help (?) icons provide information about each area. Also, click the Documentation link to access the Web Portal procedures.• For grayscale images on film, use the Grayscale Image Quality wizard to print a test page with an image from a modality. The test print provides several copies of the image with different processing parameters applied. Select the optimal image (the image with the “best” look). When you save your selection, all images from that modality will have the same processing parameters applied. See “Optimizing Grayscale Images on Film” on page 3-7.• For grayscale images on paper, you can optimize the transfer function table (TFT) settings. See “Optimizing Grayscale Images on Paper” on page 3-8.• For color images on paper, you can adjust the color density, with the lower number providing a lower density of ink on the paper. See “Optimizing Color Images on Paper” on page 3-8.• There are also multiple types of test prints to view and experiment with the system capabilities and image processing parameters such as density, sharpness, and contrast.• If the tools above do not result in an optimal image, it might be necessary to contact your qualified service provider for help. There are additional procedures for image adjustment at the Web Portal (such as Service Class Provider configuration), but those are not recommended unless you have a strong understanding of image processing.Optimizing Grayscale Images on Film1. Load film in the media cassette. See “Loading the Media Cassette (Cut Sheets)” on page 2-4.2. At a modality, send an image to the CHROMA imager.3. Log on to the Web Portal. See “Accessing the Web Portal” on page 1-12.4. From the Web Portal menu, select Wizards > Grayscale Image Quality.5. Under Optimization Steps, click >>.6. Return to the modality, and send an image to the imager.7. Return the Web Portal. At the Grayscale Image Quality Wizard, under Optimization Steps, click >>.NOTE: The image does not print until you click >>. Then a test page prints.SHORT TERM CONFIDENTIAL

3-8 9G4260_en 2012-01-27System Settings and Status8. View the test page and visually select the optimal image. Each image is labeled with a number.9. At the Grayscale Image Quality Wizard, under Image Number, click >> to select the number of your optimal image.10. Under Optimization Steps, click >> again to continue.11. Check for a “Passed” status near the bottom of the screen.12. Return to the modality and resend the image to print. Visually check the print. If it still needs improvement, return to step 5 and repeat the process.Optimizing Color Images on Paper1. Load paper in the media cassette or on the roll feeder. See “Loading the Media Cassette (Cut Sheets)” on page 2-4 or “Loading the Roll Paper into the Imager” on page 2-9.2. At a modality, send a color image to the CHROMA imager.3. Log on to the Web Portal. See “Accessing the Web Portal” on page 1-12.4. From the Web Portal menu, select Configuration > Paper Density Control > Paper Density Control.5. Click Modify, and then next to Paper Density Value, click >> to increase or decrease the density.6. Click Save.7. Return to the modality and resend the image to print. Visually check the print. If it still needs improvement, return to step 2 and repeat the process.Optimizing Grayscale Images on Paper1. Load paper in the media cassette or on the roll feeder. See “Loading the Media Cassette (Cut Sheets)” on page 2-4 or “Loading the Roll Paper into the Imager” on page 2-9.2. At a modality, send a color image to the CHROMA imager.3. Log on to the Web Portal. See “Accessing the Web Portal” on page 1-12.To optimize the images for your preferences, it might be necessary to try the transfer function table (TFT) sets and related settings on the next page. The settings are based on the types of images you are printing.NOTE: With images of Monochrome1 photometric interpretation, the image’s areas of lower density display and print in lighter shades, while the higher densities are darker. Monochrome2 images are the opposite: the lower densities display and print in darker shades while the higher densities are lighter.SHORT TERM CONFIDENTIAL

System Settings and Status2012-01-27 9G4260_en 3-9NOTE: The DICOM header tag for Monochrome1 and 2 is 0028,0004.4. From the Web Portal menu, select Configuration > DICOM SCP > Configuration.5. From the SCU menu, select the service class user (SCU) from which you are printing.6. Click Modify.7. Enter the first set of parameters from the table above that matches the SCU. For example:• For CT images, enter the settings for row 1a. • For CR images with Monochrome2 photometric interpretation, enter the settings for row 1b.• For each, select Always Apply.8. Return to the modality and resend the image to print. Visually check the print. If it still needs improvement, return to step 4 and retry different settings. For example, you might experiment with the Perception LUT Contrast setting for images using the TFT Set LINODS.w87. TFT and Related SettingsTFT Set Smoothing TypePerception LUT ContrastDmax Types of Image Notes1a LINODS.w87 15 7 2.8 CT, MI, Nuclear Medicine, Ultrasound, DSA/Digital FluoroscopyTo increase the image contrast, decrease the Perception LUT Contrast setting.1b LINODS.w87 5 7 2.8 CR, DR with Monochrome2 Photometric InterpretationMonochrome2 = Perception or Luminance space. To increase the image contrast, decrease the Perception LUT Contrast setting.2 LD4305.w87 5 1 2.8 CR, DR with Monochrome1 Photometric InterpretationMonochrome1 = Density space. If using LINODS.w87 and the printed image is inverted (black bone on white), use LD4305.w87 instead. SHORT TERM CONFIDENTIAL

SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-14Maintenance and TroubleshootingOverviewThis chapter provides instructions to: • Clean the imager, either as preventive maintenance or to solve problems• Correct any print quality issues• Realign the print head• Replace the cutter blade• Correct any errors at the imager• Correct any print jams• Restart the DICOM interface• Restore the system software• Call for supportSHORT TERM CONFIDENTIAL

4-2 9G4260_en 2012-01-27Maintenance and TroubleshootingKeeping the Imager CleanClean the Outside To keep the imager in optimal operating condition, clean it regularly (about once a month).IMPORTANT: Always leave cut sheet media in the carrier when you remove it from the cassette. Store the unused cut sheet media in its carrier, and store all unused media in the original carton.1. Remove any media from the imager. See “Chapter 2 Working with the Media and Ink” for help.2. Shut down the imager. Wait for the screen to go dark, and then unplug the power cable from the electrical outlet.3. Use a soft, clean cloth to carefully remove any dust or dirt.If there is heavy dust or dirt, clean the imager using a soft, clean cloth dampened with a mild detergent. Then wipe off with a dry, soft cloth.CAUTION:Never use benzene, thinners, or alcohol to clean the imager. They could cause discoloration and deformities.Uneven Prints: Clean the Cassette Printing PathIMPORTANT: Make sure you are printing through the DICOM interface according to the instructions in this guide.Clean the cassette printing path if the prints are dirty or if particles are on the print. If the printing path is not clean, the ink might be applied unevenly.1. Load A2 or 43 cm (17 in.) CHROMA paper in the media cassette.2. Check that the imager is on, and change the media type to Cut Sheet:• Press to display the Paper Type Menu.• Press to select Cut Sheet.•Press OK. 3. Press . Paper ejects from the cassette.4. Repeat steps 1–3 until the media is not dirty. 5. Return the media type to Paper Roll/Cut if you will print from the roll feeder.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-3“Dirty” Prints: Clean the InsideIMPORTANT: Make sure you are printing through the DICOM interface according to the instructions in this guide.1. Shut down the imager. Wait for the screen to go dark, and then unplug the power cable from the electrical outlet.2. Wait for one minute.3. Open the imager cover and use a soft, clean cloth to carefully clean away any dust or dirt inside the imager.Wipe the shaded area in the illustration below, avoiding the areas shown. To avoid spreading the dirt, wipe from the inside to the outside. If there is heavy dust or dirt, clean it using a soft, clean cloth dampened with a mild detergent. Then, wipe the inside of the imager with a dry, soft cloth.CAUTION:Do not touch the roller and the ink absorption (indicated below); otherwise, prints may be soiled.Do not touch the ink tubes inside the imager. This can damage the imager.4. Close the imager cover.Wipe only this areaDo not touch these parts; also do not touch inside the imagerSHORT TERM CONFIDENTIAL

4-4 9G4260_en 2012-01-27Maintenance and TroubleshootingWhite Powder on the Platen: Clean the PlatenIMPORTANT: Make sure you are printing through the DICOM interface according to the instructions in this guide.1. Shut down the imager. Wait for the screen to go dark, and then unplug the power cable from the electrical outlet.2. Wait for one minute.3. Use a toothpick or similar object to push in the paper particles on the platen. The particles look like white powder.CAUTION:Do not touch the roller and the ink absorption; otherwise, the prints may be soiled.Do not touch the ink tubes inside the imager. This can damage the imager.4. Close the imager cover.Smudged Prints from the RollerIf the roll paper prints are smudged or soiled, clean the roller:1. Turn on the imager.2. If not already loaded, load the roll paper. See “Loading the Roll Paper” on page 2-9.3. Press to feed the paper through the imager. The paper feeds while you hold the button. Feed the paper until it comes out clean.Do not touch these parts; also do not touch inside the imagerSHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-5Running a Nozzle Check to Avoid or Correct Print IssuesChecking and Cleaning the NozzlesRun a nozzle check:• Regularly to keep your imager in optimal condition. The manufacturer recommends running a nozzle check daily.• If white lines or spots appear in the prints, or if the imager is not printing evenly.• If print quality has declined in any way.There are multiple approaches:• Auto Nozzle Check—If the imager detects a clogged nozzle, you are notified and Auto Cleaning is initiated. To set up Auto Nozzle Check, see “Setting up Automatic Nozzle Check” on page 3-5.NOTE: You can set the intensity of the Auto Cleaning process. See “Auto Cleaning” on page 3-2.• Print Check Pattern—Checks the nozzles for clogs. If you see banding or gaps in the printed pattern, perform a head cleaning.To start a nozzle check or a print check pattern:1. Load A4 or larger paper or roll paper. 2. Press to display the Ink Menu.3. Press to select Nozzle Check, and then press .4. Press to select Auto Nozzle Check or Print Check Pattern, and then press OK. 5. Check the results.Nozzle Check Print Check PatternA message displays if a clog is detected. If detected, press to start Auto Cleaning, and then press OK to close the Ink Menu.Review the test print for any gaps in the pattern.Example of clean nozzlesExample of clogged nozzlesIf any segments are missing in the nozzle check pattern, perform a head cleaning.SHORT TERM CONFIDENTIAL

4-6 9G4260_en 2012-01-27Maintenance and TroubleshootingWorking with the Print HeadOverview • Clean the print head if the print quality declines, for example, if the printout is blurry or the color is incorrect or missing.• Ink is consumed when head cleaning is performed.• When you perform All Colors/All Colors (Powerful) in Manual Cleaning from the imager, ink is consumed from all of the ink cartridges. Even if you are using only black inks for black and white printing, the color inks are also consumed.• If the Ink Check light ( ) is on, there might not be enough ink to perform an ink check. Replace the near-empty ink cartridge with a new one. Check the display screen to know which cartridge to replace. See “Checking the Ink Levels” on page 2-20.• If you repeat head cleaning in a short time period, the maintenance tank may fill up quickly due to a small amount of ink evaporation in the tank. Install a new maintenance tank if there is not enough empty space in the tank. See “Replacing the Maintenance Tanks” on page 2-24.• If the nozzles are still clogged after cleaning the print head several times, try the power cleaning.• The power cleaning cycle consumes more ink than normal head cleaning. Check the remaining ink level in advance, and prepare a new ink cartridge before you start cleaning if the ink is low.• If the nozzles are still clogged after performing power cleaning, shut down the imager and leave it overnight or longer. When left for some time, the clogged ink may dissolve. If the nozzles are still clogged, contact your qualified service provider.• If a cleaning error message displays, see the next procedure to check for the cause and solution.Clean the Print Head 1. Run a nozzle check to make sure you need to clean the print head. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.2. Check that the imager is in the Ready state and the red Ink Check light is not on or flashing. 3. Press . The Ink Menu displays.4. Press to select Manual Cleaning, and then press . NOTE: Run the powerful cleaning only if the normal cleaning process has not cleared the nozzles. The power cycle uses a large quantity of ink.• Select a color pair to clean—Press to select the color pair, and press . Press to select Execute or Execute (Powerful), and then press OK. The cleaning starts.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-7• Clean all colors—Press to select All Colors, and press . Press to select Ye s, and then press OK. The cleaning starts.• Power clean all colors—Press to select All Colors (Powerful), and press . Press to select Ye s, and then press OK. The cleaning starts.The power light flashes and head cleaning starts. It takes from one to 10 minutes. Cleaning is finished when the Power light is on.NOTE: If Auto Nozzle Check is set to On, it might take 10 minutes or longer.5. Print a nozzle check pattern, and check the result (see “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5).Align the Print Head Aligning the print head is important to ensure the best print quality. If banding appears on your prints, or if prints look grainy or blurry, align the print head.Perform a nozzle check before you align the print head. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.1. Load A4 or larger CHROMA paper or roll paper. 2. Press .3. Use the arrow buttons to select Head Alignment, and then press .4. Press twice and select the paper type. Press , select the paper type, and then press OK.5. Press three times, and then press to select Alignment.6. Press to select Auto, and then press again. UNI-D is selected.IMPORTANT: Each alignment takes about seven minutes. Do not open the front cover or shut down the imager during this process.7. Press , and then press OK to start the alignment.8. When the process is complete, press .9. Select Head Alignment, Alignment, and Auto.10. Select Bi-D 5-Color, press , and then press OK.11. When the process is complete, press to exit.SHORT TERM CONFIDENTIAL

4-8 9G4260_en 2012-01-27Maintenance and TroubleshootingCorrecting Paper Cutting ProblemsReplace the cutter if it is not cutting cleanly. It might not be necessary to replace the cutter during the life of the imager.Use a cross-head screwdriver to replace the cutter. CAUTION:Be careful not to damage the cutter blade. Dropping it or knocking it against a hard object can damage the blade.1. Turn off the imager.IMPORTANT: Always leave cut sheet media in the carrier when you remove it from the cassette. Store the unused cut sheet media in its carrier, and store all unused media in the original carton.2. If media is loaded in the imager, remove it. 3. Open the cartridge covers on both sides.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-94. Open the top cover.5. Use the screwdriver to remove the four screws that hold the cover in place, and then remove the cover.SHORT TERM CONFIDENTIAL

4-10 9G4260_en 2012-01-27Maintenance and Troubleshooting6. Locate and open the cutter cover. Pull the cover toward you while holding down the lock.7. Using the screwdriver, loosen the screw that holds the cutter in place, and then pull the cutter straight out.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-118. To install the new cutter, insert it so the pin on the imager aligns with the hole on the cutter. Use the screwdriver to tighten the screw to hold the cutter in place.9. To close the cover, push it in until you hear a click.10. To return the front cover, reinsert and tighten the four screws that hold the cover in place. Use the screws with washers for the front (the cartridge cover area).NOTE: If the front cover is not correctly installed, an error displays and the imager will not respond.11. Close the top cover and the cartridge covers.SHORT TERM CONFIDENTIAL

4-12 9G4260_en 2012-01-27Maintenance and TroubleshootingCorrecting ErrorsIntroduction There are several places to check the status of the system:• The alert lamp on the imager automatically lights or flashes when an error or warning occurs. You can set or change the alert lamp settings in maintenance mode. (See “Alert Settings” on page 3-2.)• The imager display screen shows messages that are related to printing functions, for example, ink low and maintenance messages. If an error occurs, the alert lamp and/or the display screen light illuminate, and a message displays.• The small screen on the DICOM Interface shows the media size for loaded and requested media for the jobs from modalities.• The Web Portal provides more detailed status and system information.Messages and suggested correction actions are provided in this chapter.Messages at the Imager Display Screen and Suggested ActionsMessage ActionInk Cartridge Expended. Replace ink cartridge.Replace the ink cartridge. See “Replacing the Ink Cartridges” on page 2-21.Ink Cartridge Alert. Please use genuine Epson ink cartridges.Replace the ink cartridge with an ink cartridge that is supported by this imager.Ink Cartridge AlertNon-genuine cartridge!Quality of non-genuine ink may vary.Non-genuine cartridge may not perform at optimum.Continue? Decline or AcceptSelect Decline, and then replace the ink cartridge with a supported ink cartridge. Ink Cartridge Alert. Replace ink cartridge(s).Remove the ink cartridge and reinstall it. If the message still displays, install a new ink cartridge.Condensation may occur in the ink cartridge. Leave it at room temperature for at least four hours before reinstalling the ink cartridge.Ink Cartridge Error. Please install the correct ink cartridge.Remove the ink cartridge, and install an ink cartridge that is supported by this imager.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-13No Ink Cartridges. Install ink cartridge(s).Install ink cartridges. See “Replacing the Ink Cartridges” on page 2-21.Ink Low Prepare a new ink cartridge for replacement.Cartridge Cover Open. Close right and left cartridge covers.Close the ink cartridge covers.Cartridge Cover Open. Close left cartridge cover.Close the cartridge cover on the left.Cartridge Cover Open. Close right cartridge cover.Close the cartridge cover on the right.Paper Load Error. Remove the rear unit to fix paper jam.See “Feeding or Ejecting Problems/Media Jams” on page 4-21 and remove the jammed media.Paper Load Error. Remove paper cassette to fix paper jam.See “Feeding or Ejecting Problems/Media Jams” on page 4-21 and remove the jammed media.Cleaning ErrorNot enough inkContinue cleaning?Yes (Recommended) or NoYes—The ink cartridge replacement message displays. Replace the ink cartridge with a new one to continue cleaning.No—Cleaning is canceled and the imager returns to a Ready state.Cleaning ErrorAutomatic head cleaning failed.Retry?Yes or NoClogged nozzles could not be cleared even after cleaning. Select Yes to clean again. If the cleaning does not start, cancel the printing, shut down the imager, wait for a while, and then restart the imager.If you select No, cleaning is canceled and the imager returns to a Ready state.Cleaning ErrorNot enough empty space in maint box 1.Continue cleaning?Yes (recommended) or NoYes—The maintenance box 1 replacement message displays. Replace the maintenance tank with a new tank to continue cleaning. See “Replacing the Maintenance Tanks” on page 2-24.No—Cleaning is canceled and the imager returns to a Ready state.Ink Too Low To CleanReplace ink cartridge.The cartridge being used can be installed again for printing.The message displays when Yes is selected due to a Cleaning Error or Nozzle Clog Detected error. Replace the ink cartridge with a new cartridge. See “Replacing the Ink Cartridges” on page 2-21.Auto CleaningThis feature is not available now.Print the check pattern in the Nozzle Check Menu.Press OK to remove the message. Then run a print check pattern. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.Message ActionSHORT TERM CONFIDENTIAL

4-14 9G4260_en 2012-01-27Maintenance and TroubleshootingAuto Nozzle CheckThis feature is not available now.Print the check pattern in the Nozzle Check Menu.Press the OK button to remove the message. Then run a print check pattern. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.No Front Cover. Attach front cover then restart imager.Shut down the imager, and then install the front cover. Start the imager. Clogged nozzles detected. Cleaning recommended.Perform head cleaning to remove any clogs. The message displays until the clogged nozzles have been cleared, but it clears when a check pattern is printed. You can print when this message displays. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.Nozzle Clog DetectedNot enough ink.Continue cleaning?Yes (Recommended) or NoYes—The ink cartridge replacement message displays. Replace the ink cartridge with a new cartridge to continue cleaning. See “Replacing the Ink Cartridges” on page 2-21.No—Cleaning is canceled and the imager returns to a Ready state.Nozzle Clog DetectedNot enough empty space in maint box 1.Continue cleaning?Yes (recommended) or NoYes—The maintenance box 1 replacement message displays. Replace the maintenance tank with a new tank to continue cleaning.No—Cleaning is canceled and the imager returns to a Ready state.Wrong Support Position. Lower the paper eject support.The media eject support is raised. Lower the eject support.Wrong Support Position. Raise the paper eject support.The media eject support is lowered. Raise the eject support.No Rear Unit. Install the rear unit.Install the rear unit. For instructions, see “Feeding or Ejecting Problems/Media Jams” on page 4-21.F/W Install Error. Update failed.Restart the imager.Shut down the imager, wait for a few minutes, and then start the imager again.If this message appears again, contact your qualified service provider.Imager Cover Open. Please close the cover.Close the imager cover.Maint Box 2 Unlocked. Lock lever for maintenance box 2.Lock maintenance tank 2 (borderless tank).Not Enough Empty Space. Replace the maintenance box 1.Replace the maintenance tank 1 (maintenance box) with a new tank. See “Replacing the Maintenance Tanks” on page 2-24.Message ActionSHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-15Maintenance Box 1 Error. Replace maintenance box 1.Set the maintenance tank 1 (maintenance box) again correctly. If the error occurs again, replace maintenance tank 1 with a new tank. See “Replacing the Maintenance Tanks” on page 2-24.Maintenance Box 2 Error. Replace maintenance box 2.Set the maintenance tank 2 (borderless tank) again. If the error occurs again, replace maintenance tank 2 with a new tank. See “Replacing the Maintenance Tanks” on page 2-24.Replace Maint Box 1. At the end of service life. Replace maint box 1.Replace the maintenance tank 1 (maintenance box) with a new tank. See “Replacing the Maintenance Tanks” on page 2-24.No Maintenance Box 1. Install maintenance box 1.Install the maintenance tank 1 correctly. See “Replacing the Maintenance Tanks” on page 2-24.No Maintenance Box 2. Install maintenance box 2.Install the maintenance tank 2 (borderless tank) correctly.Maint box near end of service life.To check if free space is running low in maintenance tank 1 or 2, look at the display screen. See “Checking the Maintenance Tank Levels” on page 2-23. Replace the appropriate tank. See “Replacing the Maintenance Tanks” on page 2-24.No Paper Cassette. Install paper cassette.Install the media cassette. See “Loading the Media Cassette (Cut Sheets)” on page 2-4.Paper Size Error. Load correct paper size.The loaded media width is not supported. Check the following conditions and load media with an appropriate width.The smallest media width is 20.32 cm (8.00 in.).Make sure that A4 or larger media is loaded when performing head alignment.If an error message displays even though media with an appropriate width is loaded, set Paper Size Check to Off. Press Menu > Printer Setup > Paper Size Check > Off.Paper Setting Error. This paper cannot be loaded from paper cassette.The wrong type of media has been loaded in the cassette. Press the button and select Job Cancel, then remove the media from the cassette. Paper Jam. Remove paper from imager.Power off and then on.See “Feeding or Ejecting Problems/Media Jams” on page 4-21.Message ActionSHORT TERM CONFIDENTIAL

4-16 9G4260_en 2012-01-27Maintenance and TroubleshootingRoll Paper ErrorsPaper Out. Load paper in paper cassette.Confirm that no jobs are in the process of printing, then remove the cassette and load the media.IMPORTANT: Always leave the media in the carrier when you load it into and unload it from the cassette. Store unused media in its carrier and in the original carton.Paper Sensor Error. Loaded paper or print out has a problem. Refer to manual for details.If this error displays when performing an automatic head alignment, check the following items:• Did you load media that is not supported for automatic head alignment? Automatic head alignment cannot be performed with plain paper or thick paper. Install CHROMA paper.• Did you load media that is smaller than A4 size? Load paper that is A4 size or larger.• Are any nozzles clogged? Perform a head cleaning. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.If this error displays at any other time, make sure that CHROMA paper is loaded.Message ActionMessage ActionPaper Cut Error Roll paper is not cut correctly. Press to release the paper presser, and then remove the uncut paper.The paper cutter may be blunt. Replace the cutter. See “Correcting Paper Cutting Problems” on page 4-8.Paper Eject ErrorPress the button, or Remove paper and press the button. This error might occur when you are near the end of a roll of paper. When a paper roll is almost depleted, the imager cannot print beyond a certain point on the roll. If this error occurs, follow the instructions on the screen to press to rewind (and remove) the roll paper, and install a new roll.Paper Jam orPaper Jam/Remove paper from printer. Power off and then on.Press to release the paper presser, and then remove the paper. See “Clearing a Roll Paper Jam” on page 4-24.Paper Load Error/Press the button and reset roll paper.Press to rewind the roll paper, and then load it into the imager. See “Loading the Roll Paper into the Imager” on page 2-9.Paper Low Prepare a new roll paper for replacement. See “Replacing the Roll Paper” on page 2-16.Paper Out/Press the button.Press to release the paper presser, and then load more roll paper. See “Replacing the Roll Paper” on page 2-16.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-17Maintenance or Service Call is RequiredCutter unit nearing end of service life. Recommend replacing the cutter unit.The paper cutter may be blunt. Replace the cutter. See “Correcting Paper Cutting Problems” on page 4-8.Paper Setting ErrorRoll paper is loaded.Remove it and change paper source to roll paper.Remove the roll paper and see “Replacing the Roll Paper” on page 2-16 to install the roll paper again.Paper Skew/Load paper correctly.The paper is not loaded straight. Press to release the paper presser, and then load the paper correctly. See “Replacing the Roll Paper” on page 2-16.Message ActionMessage ActionMaintenance Request. Code XXXX (the code varies by the error, for example Code 1234)Refer to the manual.An imager part is nearing the end of its service life.Contact your qualified service provider and provide the maintenance request code.You cannot clear the maintenance request until the part is replaced. A service call occurs if you continue to use the imager.Call For Service. Code XXXX (the code varies by the error, for example, Code 1125)Power off and then on.If this doesn't work, note the code and call for service.A call for service occurs when:• The power cable is not connected securely• An error that cannot be cleared occursWhen a call for service has occurred, the imager automatically stops printing. Shut down the imager, disconnect the power cable from the outlet and from the AC inlet, and then reconnect. Restart the imager multiple times. (Press the power switch on the front of the imager multiple times.)If the call for service displays again, contact your qualified service provider. Provide the code that displays.SHORT TERM CONFIDENTIAL

4-18 9G4260_en 2012-01-27Maintenance and TroubleshootingTroubleshootingImager is Not PrintingImager Sounds Like it is Printing, but Nothing PrintsSymptom ActionThe imager does not start. Make sure the power cable is securely plugged into the imager, into the DICOM interface, and into the electrical outlets.Is there a problem with the electrical outlet? Make sure your outlet works by connecting the power cable for another electric product.The print job from the modality fails.Check that the imager is selected as the print destination at the modality. If yes, check the Web Portal software to confirm that the modality network information has been configured correctly. See “Accessing the Web Portal” on page 1-12.Check that the network cable is connected properly on both sides and that the network is operating at the site.Check the connection between the DICOM interface and the imager. Check the USB cable and disconnect, then reconnect as necessary. Make a test print from the DICOM interface to the imager to confirm connectivity.The imager is not communicating with the DICOM interface.Make sure the USB cable is securely connected into the correct terminal of the DICOM interface and the imager. Also, make sure the cable is not broken nor bent. If you have a spare USB cable, try connecting with the spare cable.You cannot print over the network.Are the network settings correct? Ask your network administrator for the network settings. Check the settings at the Web Portal. See “Accessing the Web Portal” on page 1-12.The imager has an error. Confirm if errors have occurred by checking the lights and messages on the imager display screen.Symptom ActionThe print head moves, but nothing prints.Confirm the imager operation.Print a nozzle check pattern. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.Check the next section if the nozzle check pattern does not print correctly.If “Motor Self Adjustment” displays on the display screen, the imager is adjusting the internal motor. Leave the imager on and wait for a while.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-19Prints Do Not Look as ExpectedThe nozzle check pattern does not print correctly.Perform head cleaning. The nozzles may be clogged. Print a nozzle check pattern again after performing head cleaning. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.If the imager has not been used for a while, the nozzles may have dried ink inside, which can cause a clog. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.Symptom ActionSymptom ActionPrint quality is poor, uneven, too light, or too dark.• Are the print head nozzles clogged? If the nozzles are clogged, specific nozzles do not fire ink and the print quality declines. Print a nozzle check pattern. See “Running a Nozzle Check to Avoid or Correct Print Issues” on page 4-5.• Did you align the print head? See “Align the Print Head” on page 4-7.• Are you using a supported ink cartridge? The imager is developed for use with specific ink cartridges. If you use non-supported ink cartridges, the prints may smear, or the color of the printed image may be changed because the remaining ink level is not correctly detected. • Are you using an old ink cartridge? The print quality declines when an old ink cartridge is used. Replace the old ink cartridge with a new cartridge. Use the ink cartridges before the expiration date printed on the packaging (within six months after installing in the imager). For more information, see “Extending the Life of Ink Cartridges During Periods of Inactivity or Low Use” on page 2-19.• Did you open the imager cover while printing? If the imager cover is opened while printing, the print head stops suddenly, which can cause unevenness in the color. Do not open the imager cover while printing.• Does “Ink Low” appear on the display screen? The print quality may decline when the ink is low. Replace the ink cartridge. If there is a difference in color after replacing the ink cartridge, try cleaning the print head. See “Clean the Print Head” on page 4-6.The image quality of the prints needs improvement.See “Optimizing the Look of the Image” on page 3-7.The print is not positioned properly on the paper.IMPORTANT: Make sure you are printing through the DICOM interface according to the instructions in this guide.• Is the media size setting correct?• Is the media skewed? Check that the cassette is installed properly, and that the media carrier is loaded properly.SHORT TERM CONFIDENTIAL

4-20 9G4260_en 2012-01-27Maintenance and TroubleshootingTop Line of the DICOM Interface Screen is BlankVertical ruled lines are misaligned.Is the print head misaligned? See “Align the Print Head” on page 4-7.The printed surface is scuffed or soiled.• Are you using CHROMA media inside a carrier? Only CHROMA media is supported.• Have changes in temperature or humidity damaged the media? Store and use the CHROMA media in an appropriate environment. See “Environmental Recommendations” on page 5-2.• Start with a new package of CHROMA media if the media seems to be altered in any way.The paper is creased. • Have changes in temperature or humidity damaged the media? Store and use the CHROMA media in an appropriate environment. See “Environmental Recommendations” on page 5-2.• Start with a new package of CHROMA media if the media seems to be altered in any way.The reverse side of the printed paper is soiled.IMPORTANT: Make sure you are printing through the DICOM interface according to the instructions in this guide.Is ink dry on the printed surface? Depending on the printing density and media type, the ink may take a while to dry. Do not stack the media until the printed surface is dry.Symptom ActionSymptom ActionThe DICOM interface typically displays the loaded media size on the top line of the screen. If nothing displays on the top line, there might be an issue reading the RF tag on the media.Cut Sheets—Check the media cassette to confirm that the media is loaded correctly. The media carrier in the cassette might be empty or loaded incorrectly. Remove and reseat the media carrier. The RF tag is the chip on the underside of the media carrier. If it is loose or is not attached firmly to the media carrier, the media might not be counted properly. Load a new media package (media plus carrier) in the media cassette.Roll Paper—Check that the roll paper is loaded correctly.The RF tag is the chip on the outside of the paper roll. If it is loose or not attached firmly to the roll, the media might not be tracked properly. Load a new roll if necessary.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-21Feeding or Ejecting Problems/Media JamsSymptom ActionThe imager is not feeding or ejecting media.• Is the media cassette loaded in the correct position? • If you are printing to roll paper and media cassette, make sure Roll Paper/Cut is selected from the Paper Type Menu. If you are printing only to media cassette, select Cut Sheet from the Paper Type Menu.• Are you using CHROMA media? If using cut sheets, is the paper inside a media carrier? Only CHROMA media is supported.• Have changes in temperature or humidity damaged the media? Store and use the CHROMA media in an appropriate environment. See “Environmental Recommendations” on page 5-2.• Start with a new package of CHROMA media if the media seems to be altered in any way.• Loading the media in the imager with the wrong side up will cause feeding problems. Make sure the media and the carrier are positioned correctly, with CHROMA visible on the top of the carrier, and facing up in the cassette. If the media has been inadvertently removed from the carrier, it must be reinserted in the correct orientation or you are likely to have feed issues.– Film—The printed side of the media must face down inside the carrier and in the cassette.– Glossy paper—The printed side (the glossy side) must face down inside the carrier and in the cassette.– Matte paper—The printed side (the lightest side) must face down inside the carrier and in the cassette.Unable to feed or eject paper. • Is media jammed in the imager (from the media cassette)? Open the cover of the imager and check that there are no jams or foreign objects in the imager. If media is jammed, see the next step.SHORT TERM CONFIDENTIAL

4-22 9G4260_en 2012-01-27Maintenance and TroubleshootingMedia sheets from the cassette have jammed while printing.To remove jammed media:• Remove the output tray and the media cassette.• Remove the jammed media from where the cassette was inserted.Symptom ActionSHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-23• If media is jammed in the back, remove the rear unit by moving the tabs toward the inside and pulling the rear unit toward you. Then remove the jammed media.• Replace the rear unit.With the rear unit's tabs moved to the inside, push it into the imager firmly until you hear it click into place.• Shut down the imager, and then start it again. Reload the media cassette and restart printing.Symptom ActionSHORT TERM CONFIDENTIAL

4-24 9G4260_en 2012-01-27Maintenance and TroubleshootingClearing a Roll Paper Jam1. Press to release the paper presser.2. Open the roll paper cover and using a cutter, cut off the paper at the slot of the roll paper feeder.3. Lift up on the right side of the spindle from the gray flange to bring the spindle to a 45 ° angle (A). Pull the spindle up and to the right to remove it from the spindle holder.4. Remove the jammed paper from the roll paper feeder or front manual feeder.5. Open the top cover and remove any other jammed paper.6. Turn off the imager, and then turn it back on. Reload the paper and restart printing. See “Loading the Roll Paper” on page 2-9.H210_0852BAAGray flangeSHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-25An Icon on my Print Indicates a Sizing Issue, or some of the Image or Information is Cut OffWhen you send an image to print, the image size should be appropriate for the media that the imager supports. If an image received for printing is too large to be printed at the CHROMA imager, the image file will be altered to let it print. • Scale—The full image is printed but at a smaller size than requested. This enables the job to print on the requested media size.• Crop—The image’s perimeter is removed to let the image print, while the scale of the image’s anatomical area of interest is retained.Cropping allows “true size” printing for larger images. True size printing provides a common scale between images captured on analog systems and printed digital images. The anatomical area of interest is printed at the same size that it is captured on the analog system. Measurements and comparisons between printed analog and digital images are simplified.To change the setting for image resizing, access the Web Portal (see “Accessing the Web Portal” on page 1-12). Navigate to Configuration > DICOM SCP > SCP Configuration, and then click the Film and Image Options tab. NOTE: You can also specify that the imager will not perform image resizing. In that case, print jobs that are too large for the CHROMA media will not print.Symptom ActionAn icon prints with the image: The image has been scaled. Scaling allows a larger image to print at a smaller size than requested so that it can print on the installed media. If the quality of the print is less than optimal, it may be necessary to crop rather than scale.An icon prints with the image: The image has been cropped. If important information has been cropped off the print, for example, if text annotations, patient information, or anatomical areas of interest are near an outer edge of the image, it may be necessary to scale rather than crop.The image has been resized, but resizing is not acceptable.You can prevent all resizing. In that case, jobs that exceed the supported size will not print. Access the SCP Configuration section of the Web Portal.SHORT TERM CONFIDENTIAL

4-26 9G4260_en 2012-01-27Maintenance and TroubleshootingMiscellaneous IssuesRestarting the ImagerWhen restarting, press the power button to turn off the imager, and then wait at least 30 seconds before turning the imager on again. The imager display screen goes blank in approximately 15 seconds, but it is not fully off yet. Wait to press the button again to restart.The display screen reports “Ready” when the imager has fully started.Symptom ActionCannot remove the media cassette.• You may have shut down the imager while an error occurred.• Restart the imager, wait a few minutes, and then remove the media cassette.The display screen keeps turning off.Is the imager in sleep mode? The imager returns to its normal status when a print job is received. You can change the elapsed time before entering sleep mode. See “Number of Minutes Before Automatic Sleep Mode” on page 3-3.Color ink runs out quickly even when printing in the Black mode or when printing black data.Color ink is consumed during the head cleaning process. When performing All Colors or All Colors (Powerful) from Manual Cleaning, all nozzles are cleaned and some ink from all colors is consumed. (Even when Black mode is selected, the ink for all colors is consumed while cleaning.)The red light is on inside the imager.This is not a failure. The red light is normally on inside the imager.The imager will not accept images.It is possible for the hard-disk storage to become full. In that case, new jobs might be rejected. Wait for the hard disk to automatically delete the oldest jobs from the print queue. Restart the DICOM interface.SHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-27The DICOM Interface is Non-Responsive (How to Restart)If the DICOM interface is not responding, you might restart it to correct various conditions.IMPORTANT: Do not hold down the power switch. 1. Press and release the power switch. Wait at least five minutes as the DICOM interface shuts down.2. Press and release the power switch again. Wait as the DICOM interface starts. It is fully powered up when the media size displays on the DICOM interface screen. NOTE: If media is not loaded in the imager, the DICOM interface screen will be illuminated but it will be blank.Restoring the System Software—GhostingThe “ghosting” procedure is used to restore the CHROMA system. This procedure is not recommended unless you are instructed to follow it by qualified service personnel (for example, if your system is having issues and you have called the support number). To follow the ghosting procedure, you must use the USB flash drive that arrived with your new CHROMA system.You can connect a monitor to the DICOM interface to view the progress of the ghosting procedure. This helps if any problems occur during the procedure and if you need to be away from the system. If you do not connect a monitor, you will need to be at the system to hear the beeps that indicate whether ghosting was successful.H210_0614ACSHORT TERM CONFIDENTIAL

4-28 9G4260_en 2012-01-27Maintenance and Troubleshooting1. Retrieve the backup file for your system. If you do not have a backup file, make a new backup and save it to your computer.NOTE: A backup file was created at the end of the CHROMA installation. If you need to create a new backup file, log on to the Web Portal, and then click the Documentation link. See the procedure, “Backing up the Software” in the Web Portal documentation, and follow the instructions to make a backup file.NOTE: If you do not have a backup file and cannot create a new file, you must reconfigure the system after you perform this ghosting procedure.2. Shut down the DICOM interface. (Press and release the power switch.)3. Install the portable USB flash drive that contains the ghost software into an unused USB port on the back of the DICOM interface.4. Press and release the DICOM interface power switch again to begin ghosting.Ghosting takes approximately 10 minutes. The imager beeps when ghosting has completed. If you connected a monitor, the screen displays the progress and reports when ghosting has completed.• When ghosting completes successfully, the DICOM interface beeps eight times in one-second, high-frequency tones.• If ghosting fails, the DICOM interface beeps five times in three-second, low-frequency tones.5. After ghosting has completed, wait 20 seconds and then power off the DICOM interface.6. Remove the USB flash drive.Unused USB portsSHORT TERM CONFIDENTIAL

Maintenance and Troubleshooting2012-01-27 9G4260_en 4-297. Log on to the Web Portal, and then click the Documentation link. See the procedure, “Backing up the Software” in the Web Portal documentation. Follow the instructions to restore from a saved backup file.orIf you do not have a configuration file to restore, perform the following procedures from the Quick Start Guide, 9G4261:• “Set up your PC to Communicate with the Imager”• “Log on to CARESTREAM Web Service Portal Software”• “Configure the Site-Specific Information”• “Start CARESTREAM Remote Management Services”• “Reconfigure your PC to Connect to the Imager”• “Verify the Image Look”• “Back up the Configuration Parameters”Calling for SupportIf you cannot correct a condition and need help, call for support. Have the following information ready when you call:• Serial number (on the side of the DICOM interface)• K-number (on the side of the DICOM interface)• Error code from the display screen and/or code and error message from the Web PortalWorldwide support numbers are available at www.carestream.com. Click Contact Us, click World Wide Contacts, and then select your region.SHORT TERM CONFIDENTIAL

SHORT TERM CONFIDENTIAL

Specifications2012-01-27 9G4260_en 5-15SpecificationsDimensions and ClearanceMake sure that you have adequate space and clearance around the imager. Allow at least 5.08 cm (2.00 in.) clearance around the top, sides, and back of the imager.CHROMA System and required clearanceImager only (not including clearance)Height 58.6 cm (23.1 in.) 41 cm (16 in.)Width 116.3 cm (45.8 in.) 86 cm (34 in.)Depth 134.9 cm (54.1 in.) 77 cm (30 in.)Weight 53.5 kg (118.0 lb) 52 kg (115 lb)H210_0613HC15.0 cm58.6 cm134.9 cm53.3 cm15.0 cm116.3 cm18.2 cm15.0 cm(5.91 in.)(5.91 in.)(23.07 in.)(53.11 in.)(20.98 in.)(5.91 in.)(45.79 in.)(7.17 in.)SHORT TERM CONFIDENTIAL

5-2 9G4260_en 2012-01-27SpecificationsPacked DimensionsEnvironmental RecommendationsTemperature • Operating: 10–30 °C (50–86 °F)• Storage: -20–60 °C (-4–140 °F)Relative Humidity Keep the imager away from drying, direct sunlight, or heat sources to maintain the appropriate humidity.• Operating: 20–70 % without condensation• Storage: 5–85 % Surface Levelness The surface where the imager is installed must be level.Acoustical Noise Less than or equal to 50 dB-A momentary at 1 m from the front of the imager during normal operationNetwork RequirementsThe imager receives digital images from medical imaging devices (modalities) over a 10/100Base-T or 1000Base-T Ethernet Network. Height 58.4 cm (23.0 in.)Width 101.6 cm (40.0 in.)Depth 91.4 cm (36.0 in.)SHORT TERM CONFIDENTIAL

Specifications2012-01-27 9G4260_en 5-3Power RequirementsTwo power cords are provided with this equipment. The system requires agency-approved power cords with a plug type suitable for the location of use. Contact a qualified dealer for help.Connect the equipment to a power source that is suitable for the voltage and current ratings shown on the rating label. The single-phase power source, with grounding, must be provided within 2.5 m (8.0 ft) of the imager.Avoid using an outlet on the same circuit as a photocopier or air control system that regularly restarts.Power Consumption—ImagerPower Consumption—DICOM InterfaceInk CartridgesCartridge Life Two years from production date if unopened; within 6 months after opening the package, at 25 °C (77 °F).Temperature Storage (not installed): -30–40 °C (-22–104 °F); one month at 104 °FStorage (installed): -20–40 °C (-4–104 °F); one month at 104 °FCapacity 200 mlWeight Approximately 385.00 g (0.85 lb)NOTE: Dispose of the used ink cartridges carefully and in accordance with local ordinances.Operating Approximately 52 wattsStandby 20 wattsSleep mode Approximately 8.5 watts or lessPower off Approximately 0.5 watts or lessOperating Approximately 20 wattsIdle 20 wattsPower off Approximately 5 watts or lessSHORT TERM CONFIDENTIAL

5-4 9G4260_en 2012-01-27SpecificationsMediaEnvironmental For best results, use the media at:• 15–25 °C (59–77 °F)• 20–60 % relative humidityStorage • Store the unused (unprinted) media in its carrier and in the original packaging, away from high temperatures and high humidity. For best results, storage conditions should not exceed 25 °C (77 °F) and 60 % relative humidity.• Store the printed media away from extreme temperatures or high humidity.• As the CHROMA media is used with ink jet technology utilizing pigmented inks, there is no inherent shelf life or expiration date defined for these products.NOTE: Follow local waste disposal regulations. Manage the disposal appropriately to protect patient privacy rights if required by local regulations.Publication HistoryRevision Date Reason for ChangeA 2011-08-19 First releaseB 2011-09-19 Corrected an error on page 1-8C 2012-01-27 To support CHROMA Release 2. Added details throughout the guide for the roll feeder and roll paper, removed information about power management mode, added procedures for managing image quality, changed the time from one minute to five minutes when restarting the DICOM interface, added the procedure to restart the imager, expanded the intended use statement, added the power consumption details.SHORT TERM CONFIDENTIAL

Navigation menu