Checkpoint Systems EVOLVEM ELECTRONIC ARTICLE SURVEILLANCE (EAS) User Manual 9031090111 AMG OEM Users Manu

Checkpoint Systems Inc ELECTRONIC ARTICLE SURVEILLANCE (EAS) 9031090111 AMG OEM Users Manu

Contents

USERS MANUAL 2

Federal Communications Commission StatementWARNING!This device complies with part 15 of the FCC Rules and RSS-210 of the Canadian Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.Note> This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may course harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to tryto correct the interference by one of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected--Consult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipmentFCC ID: S8OMEDET3420 and S8OMEDET3480 - IC ID: 5849A-MEDET3420 and IC ID: 5849A-MEDET3480User’s ManualArticle number: 9031090111Large detector area like an EAS antennaSmall detector area like the PlexPost detectorNarrow distance between the detectors (less than 1.2 - 1.4 meter)Wide distance between the detectors (greater than 1.2 - 1.4 meter)Detector size adjustment preset 2Detector size adjustment preset 1High metal sensitivityNormal metal sensitivityAM filter OFFAM filter ON1 ON1 OFF2 ON2 OFF3 ON3 OFF4 ON4 OFF5 ON5 OFFS1MasterSlaveTX2 OFFTX2 ONTX2 in phase with TX1TX2 opposite phase with TX1Received signal in phase with TX1Received signal opposite phase with TX1TX1 OFFTX1 ON1 ON1 OFFTX1 in phase with TX sync (only when slave)TX1 opposite phase with TX sync (only when slave)4 ON4 OFF5 ON5 OFF6 ON6 OFF7 ON7 OFF8 ON8 OFFS2S3Select Alarm accept time window (ATW) in Advance modeSelect Alarm accept time window (ATW) in Advance modeSelect Alarm accept time window (ATW) in Advance modeSelect Alarm accept time window (ATW) in Advance modeTrolley rejection disabledTrolley rejection enabledSimple detectionAdvance detection (Receiver phase = Red flash(ANT SIZE))1 ON1 OFF2 ON2 OFF3 ON3 OFF4 ON4 OFF123Moving doorRadarRadar detection zones0Accept Time Window (ATW) forpassing the gatein outS3 Selection FunctionSimple / Trolley Acceptadvance off/on ATW ATW Type of Time Moving door radarS3 (1) S3 (2) S3 (3) S3 (4) detection Window Alarm delay Use when detection zoneOFF OFF Simple 0.1 sec No moving doorOFF ON Simple 1 sec No moving door + TrolleyON OFF OFF OFF Advance 0.65 sec 0.1 sec Moving door 0ON OFF ON OFF Advance 1.3 sec 0.1 sec Moving door (standard setting) 1ON OFF OFF ON Advance 2.6 sec 0.1 sec Moving door 2+3ON OFF ON ON Advance 2.6 sec 0.1 sec Moving door 2+3ON ON OFF OFF Advance 0.65 sec 1 sec Moving door + Trolley 0ON ON ON OFF Advance 1.3 sec 1 sec Moving door + Trolley 1ON ON OFF ON Advance 2.6 sec 1 sec Moving door + Trolley 2ON ON ON ON Advance 2.6 sec 2 sec Moving door + Trolley 3Alarm time = 4 secAlarm time = 8 sec2 ON2 OFFExtern Alarm reset OFF (Spare in)Extern Alarm reset ON (Spare in)3 ON3 OFF

Navigation menu