D Link IR845LA1 WHOLE HOME CLOUD ROUTER 2000 User Manual part 2 rev3

D Link Corporation WHOLE HOME CLOUD ROUTER 2000 part 2 rev3

Contents

User manual part 2 rev3

95D-Link DIR-845L User ManualSection 3 - CongurationAdd Website Filtering Rule:Website URL/Domain:Website FiltersSelect either DENY computers access to ONLY these sites or ALLOW computers access to ONLY these sites.Enter the keywords or URLs that you want to allow or block. Click Save Settings.Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Save Settings. You must also select Apply Web Filter under the Access Control section.
96D-Link DIR-845L User ManualSection 3 - CongurationEnter a name for the inbound lter rule.Select Allow or Deny.Check to enable rule.Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range.Enter the ending IP address. Enter 255.255.255.255 if you do not want to specify and IP range.Click the Add button to apply your settings. You must click Save Settings at the top to save the settings.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule.Name:Action:Enable:Remote IP Start:Remote IP End:Add:Inbound Filter Rules List:The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can congure inbound data ltering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features.Inbound Filters
97D-Link DIR-845L User ManualSection 3 - CongurationSPI (Stateful Packet Inspection, also known as dynamic packet ltering) helps to prevent cyber attacks by tracking more state per session. It validates that the trac passing through the session conforms to the protocol.Enable this feature to protect your network from certain kinds of “spoong” attacks. Select one of the following for TCP and UDP ports: Endpoint Independent - Any incoming trac sent to an open port will be forwarded to the application that opened the port. The port will close if idle for 5 minutes. Address Restricted - Incoming trac must match the IP address of the outgoing connection. Address + Port Restriction - Incoming trac must match the IP address and port of the outgoing connection. Enable SPI:Anti-Spoof Check:NAT Endpoint Filtering: Firewall SettingsA rewall protects your network from the outside world. The DIR-845L oers a rewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
98D-Link DIR-845L User ManualSection 3 - CongurationDMZ IP Address:PPTP:IPSEC (VPN):RTSP:SIP:Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains it’s IP address automatically using DHCP, be sure to make a static reservation on the Setup > Network Settings page so that the IP address of the DMZ machine does not change.Allows multiple machines on the LAN to connect to their corporate network using PPTP protocol.Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec throughNAT. This ALG may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG o. Please check with the system administrator of your corporate network whether your VPN client supportsNAT traversal.Allows application that uses Real Time Streaming Protocol to receive streaming media from the Internet. QuickTime and Real Player are some of the common applications using this protocol.Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are having trouble making VoIP calls, try turning this ALG o.
99D-Link DIR-845L User ManualSection 3 - CongurationEnter a name for your route.Enter the IP address of packets that will take this route.Enter the netmask of the route, please note that the octets must match your destination IP address.Enter your next hop gateway to be taken if this route is used.The route metric is a value from 1 to 16 that indicates the cost of using this route. A value 1 is the lowest cost and 15 is the highest cost. Select the interface that the IP packet must use to transit out of the router when this route is used. Name:Destination IP:Netmask:Gateway:Metric:Interface:RoutingThe Routing option is an advanced method of customizing specic routes of data through your network.
100D-Link DIR-845L User ManualSection 3 - CongurationAdvanced WirelessSet the transmit power of the antennas.This enables 802.11d operation. 802.11d is a wireless specication developed to allow implementation of wireless networks in countries that cannot use the 802.11 standard. This feature should only be enabled if you are in a country that requires it.WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.Enable this option to reduce interference from other wireless networks in your area. If the channel width is operating at 40MHz and there is another wireless network’s channel over-lapping and causing interference, the router will automatically change to 20MHz. Transmit Power:WLAN Partition:WMM Enable:HT20/40 Coexistence:
101D-Link DIR-845L User ManualSection 3 - CongurationWi-Fi Protected Setup (WPS)Enable the Wi-Fi Protected Setup feature. Note: if this option is unchecked, the WPS button on the side of the router will be disabled.Tick this option to lock the congured wireless security settings.A PIN is a unique number that can be used to add the router to an existing network or to create a new network. Only the Administrator (“admin” account) can change or reset the PIN. Shows the current PIN. Restore the default PIN of the router. Create a random number that is a valid PIN. This becomes the router’s PIN. You can then copy this PIN to the user interface of the wireless client.Enable:Lock Wireless Security Settings:PIN Settings:Current PIN:Reset PIN to Default:Generate New PIN:Wi-Fi Protected Setup (WPS) System is a simplied method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certied it across dierent products as well as manufactures. The process is just as easy as pressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin Code Method. The time reduction in setup and ease of use are quite benecial, while the highest wireless Security setting of WPA2 is automatically used.
102D-Link DIR-845L User ManualSection 3 - CongurationThis Wizard helps you add wireless devices to the wireless network.The wizard will either display the wireless network settings to guide you through manual conguration, prompt you to enter the PIN for the device, or ask you to press the conguration button on the device. If the device supports Wi-Fi Protected Setup and has a conguration button, you can add it to the network by pressing the conguration button on the device and then the on the router within 120 seconds. The status LED on the router will ash three times if the device has been successfully added to the network.There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well.Click to start the wizard and skip to page 48.Add Wireless Station:Add Wireless Device Wizard:You can also simply press the WPS button on the side of the router, and then press the WPS button on your wireless client to automatically connect without logging into the router. Refer to page 130 for more information.WPS ButtonWPS Button
103D-Link DIR-845L User ManualSection 3 - CongurationTo use the Universal Plug and Play (UPnP™) feature click on Enabled. UPnP provides compatibility with networking equipment, software and peripherals.Checking the box will allow the DIR-845L to respond to pings. Unchecking the box may provide some extra security from hackers.You may set the port speed of the Internet port to 10Mbps, 100Mbps, 1000Mbps, or Auto (recommended). Check the box to allow multicast trac to pass through the router from the Internet (IPv4).Check the box to allow multicast trac to pass through the router from the Internet (IPv6).Enable UPnP:WAN Ping:WAN Port Speed:Enable IPV4 Multicast Streams:Enable IPV6 Multicast Streams:Advanced Network Settings
104D-Link DIR-845L User ManualSection 3 - CongurationGuest ZoneCheck to enable the Guest Zone feature. The schedule of time when the Guest Zone will be active. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section or click Add New.Enter a wireless network name (SSID) that is dierent from your main wireless network.Check to allow network connectivity between the dierent zones created. Select the type of security or encryption you would like to enable for the guest zone. Enable Guest Zone:Schedule:Wireless Network Name:Enable Routing Between Zones:Security Mode:The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate from your main wireless network. You may congure dierent zones for the 2.4GHz and 5GHz wireless bands.
105D-Link DIR-845L User ManualSection 3 - CongurationIPv6 FirewallThe DIR-845L’s IPv6 Firewall feature allows you to congure which kind of IPv6 trac is allowed to pass through the device. The DIR-845L’s IPv6 Firewall functions in a similar way to the IP Filters feature.Check the box to enable the IPv6 rewall simple security.Select an action from the drop-down menu.Enter a name to identify the IPv6 rewall rule.Use the drop-down menu to select the time schedule that the IPv6 Firewall Rule will be enabled on. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Use the Source drop-down menu to specify the interface that connects to the source IPv6 addresses of the rewall rule. Enter the source IPv6 address range in the adjacent IP Address Range eld.Use the Dest drop-down menu to specify the interface that connects to the destination IP addresses of the rewall rule. Select the protocol of the rewall port (All, TCP, UDP, or ICMP).Enter the rst port of the range that will be used for the rewall rule in the rst box and enter the last port in the eld in the second box.Enable Checkbox:Congure IPv6 Firewall:Name:Schedule:Source:IP Address Range:Dest: Protocol:Port Range:
106D-Link DIR-845L User ManualSection 3 - CongurationIPv6 RoutingCheck the box next to the route you wish to enable. Enter a specic name to identify this route.This is the IP address of the router used to reach the specied destination or enter the IPv6 address prex length of the packets that will take this route. Enter the metric value for this rule here.Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router.Enter the next hop that will be taken if this route is used.Route List:Name:Destination IP/Prex Length:Metric:Interface:Gateway:This page allows you to specify custom routes that determine how data is moved around your network.
107D-Link DIR-845L User ManualSection 3 - CongurationAdminThis page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.ToolsEnter a new password for the Administrator Login Name. The administrator can make changes to the settings.Enter the new password for the User login. If you login as the User, you cannot change the settings (you can only view them).Enter a name for your router.Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings.Check to enable HTTPS to connect to the router securely. This means to connect to the router, you must enter https://192.168.0.1 (for example) instead of http://192.168.0.1. Remote management allows the DIR-845L to be congured from the Internet by a web browser. A username/password is still required to access the Web Management interface. The port number used to access the DIR-845L is used in the URL. Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-845L and 8080 is the port used for the Web Management interface.If you have enabled HTTPS Server, you must enter https:// as part of the URL to access the router remotely.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule. Details will display the current status.Admin Password:User Password:Gateway name:Enable Graphical Authentication:Enable HTTPS Server:Enable Remote Management:Remote Admin Port:Remote Admin Inbound Filter:
108D-Link DIR-845L User ManualSection 3 - CongurationTimeDisplays the current date and time of the router.Select your Time Zone from the drop-down menu.To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time.NTP is short for Network Time Protocol. A NTP server will synch the time and date with your router. This will only connect to a server on the Internet, not a local server. Check the box to enable this feature.Enter the IP address of a NTP server or select one from the drop-down menu.To manually input the time, enter the values in these elds for the Year, Month, Day, Hour, Minute, and Second and then click Set Time. You can also click Copy Your Computer’s Time Settings to synch the date and time with the computer you are currently on.Time:Time Zone:Enable Daylight Saving:Enable NTP Server:NTP Server Used:Manual:The Time Conguration option allows you to congure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be congured to automatically adjust the time when needed.
109D-Link DIR-845L User ManualSection 3 - CongurationSysLogThe Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your network.Enable Logging to SysLog Server:SysLog Server IP Address:Check this box to send the router logs to a SysLog Server.The address of the SysLog server that will be used to send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
110D-Link DIR-845L User ManualSection 3 - CongurationEmail SettingsThe Email feature can be used to send the system log les, router alert messages, and rmware update notication to your email address. Enable Email Notication: From Email Address:To Email Address:SMTP Server Address:SMTP Server Port:Enable Authentication:Account Name:Password:On Log Full:On Schedule:Schedule:When this option is enabled, router activity logs are emailed to a designated email address.This email address will appear as the sender when you receive a log le or rmware upgrade notication via email.Enter the email address where you want the email sent. Enter the SMTP server address for sending email. Enter the SMTP port used on the server.Check this box if your SMTP server requires authentication. Enter your account for sending email.Enter the password associated with the account. Re-type the password associated with the account.When this option is selected, logs will be sent via email to your account when the log is full.Selecting this option will send the logs via email according to schedule.This option is enabled when On Schedule is selected. You can select a schedule from the list of dened schedules. To create a schedule, go to Tools > Schedules.
111D-Link DIR-845L User ManualSection 3 - CongurationUse this option to save the current router conguration settings to a le on the hard disk of the computer you are using. First, click the Save button. A le dialog will appear, allowing you to select a location and le name for the settings. Use this option to load previously saved router conguration settings. First, use the Browse option to find a previously saved file of configuration settings. Then, click the Load button to transfer those settings to the router. This option will restore all conguration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router conguration settings, use the Save button above. Click to reboot the router.Save Settings to Local Hard Drive:Load Settings from Local Hard Drive:Restore to Factory Default Settings:Reboot Device:SystemThis section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
112D-Link DIR-845L User ManualSection 3 - CongurationFirmwareBrowse:Upload:After you have downloaded the new rmware, click Browse to locate the rmware update on your hard drive. Click Upload to complete the rmware upgrade.Once you have a rmware update on your computer, use this option to browse for the le and then upload the information into the access point. You can upgrade the rmware of the access point here. Make sure the rmware you want to use is on the local hard drive of the computer. Click on Browse to locate the rmware le to be used for the update. Please check the D-Link support website for rmware updates at http://support.dlink.com. You can download rmware upgrades to your hard drive from this site.After you have downloaded the new language pack, click Browse to locate the language pack le on your hard drive. Click Upload to complete the language pack upgrade.Language PackYou can change the language of the web UI by uploading available language packs.Browse:
113D-Link DIR-845L User ManualSection 3 - CongurationDynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. Check the box to enable DDNS.Select your DDNS provider from the drop-down menu or enter the DDNS server address.Enter the Host Name that you registered with your DDNS service provider.Enter the Username or key for your DDNS account.Enter the Password or key for your DDNS account.Enter a timeout time (in hours).Displays the current connection status.Enable Dynamic DNS:Server Address:Host Name:Username or Key:Password or Key:Timeout:Status:Dynamic DNSThe DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
114D-Link DIR-845L User ManualSection 3 - CongurationThe Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP address that you wish to Ping and click Ping.Enter the IPv6 address that you wish to Ping and click Ping.The results of your ping attempts will be displayed here.System CheckPing Test:IPv6 Ping Test:Ping Results:
115D-Link DIR-845L User ManualSection 3 - CongurationEnter a name for your new schedule.Select a day, a range of days, or All Week to include every day.Check All Day - 24hrs or enter a start and end time for your schedule.You must click Save Settings at the top for your schedules to go into eect.The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule.Name:Days:Time:Save:Schedule Rules List:SchedulesSchedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.
116D-Link DIR-845L User ManualSection 3 - CongurationThis page displays the current information for the DIR-845L. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.Displays the router’s time and rmware version.Displays the MAC address and the public IP settings Displays the MAC address and the private (local) IP settings for the router.Displays the 2.4GHz wireless MAC address and your wireless settings such as SSID and Channel. Displays the 5GHz wireless MAC address and your wireless settings such as SSID and Channel. Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP). General:WAN:LAN:Wireless LAN1:Wireless LAN2:LAN Computers:Device InfoStatus
117D-Link DIR-845L User ManualSection 3 - CongurationLogsLog Options:Refresh:First Page:Last Page:Previous:Next:Clear:Email Now:Save Log:You can select the types of messages that you want to display from the log. System Activity, Debug Information, Attacks, Dropped Packets, and Notice messages can be selected. Click Apply Log Settings Now to activate your settings.Updates the log details on the screen so it displays any recent activity.Click to go to the rst page.Click to go to the last page.Click to go back one page.Click to go to the next page.Clears all of the log contents.This option will send a copy of the router log to your email address congured in the Tools > Email Settings screen.This option will save the router log to a le on your computer.The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can dene what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log les to a computer on your network that is running a Syslog utility.
118D-Link DIR-845L User ManualSection 3 - CongurationStatisticsThe screen below displays the Trac Statistics. Here you can view the amount of packets that pass through the DIR-845L on both the WAN, LAN ports and the wireless segments. The trac counter will reset if the device is rebooted.
119D-Link DIR-845L User ManualSection 3 - CongurationInternet SessionsThe Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
120D-Link DIR-845L User ManualSection 3 - CongurationRoutingThis page will display your current routing table.
121D-Link DIR-845L User ManualSection 3 - CongurationThe wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.Wireless
122D-Link DIR-845L User ManualSection 3 - CongurationIPv6The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
123D-Link DIR-845L User ManualSection 3 - CongurationIPV6 RoutingThis page displays the IPV6 routing details congured for your router.
124D-Link DIR-845L User ManualSection 3 - CongurationSupport
125D-Link DIR-845L User ManualSection 4 - SecurityConnect a Wireless Client to your RouterWPS ButtonStep 2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DIR-845L router. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:Step 1 - Press the WPS button on the DIR-845L for about 1 second. The Internet LED on the front will start to blink.Step 3 - Allow up to 1 minute to congure. Once the Internet light stops blinking, you will be connected and your wireless connection will be secure with WPA2.WPS Button
126D-Link DIR-845L User ManualSection 4 - SecurityWindows® 7It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.1. Click on the wireless icon in your system tray (lower-right corner).2. The utility will display any available wireless networks in your area.Wireless IconWPA/WPA2
127D-Link DIR-845L User ManualSection 4 - Security3. Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.4. The following window appears while your computer tries to connect to the router.
128D-Link DIR-845L User ManualSection 4 - Security5. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. You can also connect by pushing the WPS button on the router.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
129D-Link DIR-845L User ManualSection 4 - SecurityWPSThe WPS feature of the DIR-845L can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to congure the WPS feature:1. Click the Start button and select Computer from the Start menu.2. Click Network on the left side.
130D-Link DIR-845L User ManualSection 4 - Security3. Double-click the DIR-845L.4. Input the WPS PIN number (displayed in the WPS window on the Router’s LCD screen or in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.
131D-Link DIR-845L User ManualSection 4 - Security5. Type a name to identify the network.6. To congure advanced settings, click the icon.Click Next to continue.
132D-Link DIR-845L User ManualSection 4 - Security7. The following window appears while the Router is being congured. Wait for the conguration to complete.8. The following window informs you that WPS on the router has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future.9. Click Close to complete WPS setup.
133D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless NetworkWindows Vista®Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orThe utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.
134D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless NetworkWPA/WPA2It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.2. Highlight the Wi-Fi name (SSID) you would like to connect to and click Connect.1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.
135D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless Network3. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
136D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless NetworkWPS/WCN 2.0The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to congure the router or third party software. When you rst set up the router, Wi-Fi protection is disabled and uncongured. To enjoy the benets of Wi-Fi protection, the router must be both enabled and congured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or manually congure. If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN button or Reset PIN to Default button. If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are nished, proceed to the next section to set up the newly-congured router.
137D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless NetworkWindows® XPWindows® XP users may use the built-in wireless utility (Zero Conguration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orThe utility will display any available wireless networks in your area. Click on a Wi-Fi network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.
138D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless NetworkIt is recommended to enable WPA on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used.2. Highlight the Wi-Fi network (SSID) you would like to connect to and click Connect.1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. WPA/WPA2
139D-Link DIR-845L User ManualSection 5 - Connecting to a Wireless Network3. The Wireless Network Connection box will appear. Enter the WPA-PSK Wi-Fi password and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The Wi-Fi password must be exactly the same as on the wireless router.
140D-Link DIR-845L User ManualSection 6 - TroubleshootingTroubleshootingThis chapter provides solutions to problems that can occur during the installation and operation of the DIR-845L. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a dierent operating system, the screenshots on your computer will look similar to the following examples.1. Why can’t I access the web-based conguration utility?When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. • Make sure you have an updated Java-enabled web browser. We recommend the following: - Microsoft Internet Explorer® 7 and higher- Mozilla Firefox 3.5 and higher- Google™ Chrome 8 and higher- Apple Safari 4 and higher• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a dierent cable or connect to a dierent port on the device if possible. If the computer is turned o, the link light may not be on.• Disable any Internet security software running on the computer. Software rewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows® XP rewall may block access to the conguration pages. Check the help les included with your rewall software for more information on disabling or conguring it.
141D-Link DIR-845L User ManualSection 6 - Troubleshooting• Congure your Internet settings:• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults.• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.• Close your web browser (if open) and open it.• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your web management. • If you still cannot access the conguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the conguration. If you have multiple computers, try connecting using a dierent computer.2. What can I do if I forgot my password?If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.
142D-Link DIR-845L User ManualSection 6 - Troubleshooting3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). To nd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL. • Click on Start and then click Run. • Windows® 95, 98, and Me users type in command (Windows® NT, 2000, XP, Vista®, and 7 users type in cmd) and press Enter (or click OK). • Once the window opens, you’ll need to do a special ping. Use the following syntax: ping [url] [-f] [-l] [MTU value] Example: ping yahoo.com -f -l 1472
143D-Link DIR-845L User ManualSection 6 - TroubleshootingYou should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you nd your MTU, you can now congure your router with the proper MTU size. To change the MTU rate on your router follow the steps below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK. • Enter your username (admin) and password (blank by default). Click OK to enter the web conguration page for the device. • Click on Setup and then click Manual Congure. • To change the MTU enter the number in the MTU eld and click Save Settings to save your settings. • Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.
144D-Link DIR-845L User ManualAppendix A - Wireless BasicsD-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and oce environments, and public areas such as airports, coee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more eciently. Increased mobility and the absence of cabling and other xed infrastructure have proven to be benecial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.Wireless Basics
145D-Link DIR-845L User ManualAppendix A - Wireless BasicsWhat is Wireless?Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or oce network.Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can aord. D-Link has all the products you need to build your network.How does wireless work? Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two dierent types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).Wireless Local Area Network (WLAN)In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.
146D-Link DIR-845L User ManualAppendix A - Wireless BasicsWireless Personal Area Network (WPAN)Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away.Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, oce, business, D-Link has a wireless solution for it.Home • Gives everyone at home broadband access • Surf the web, check email, instant message, etc. • Gets rid of the cables around the house • Simple and easy to use Small Oce and Home Oce • Stay on top of everything at home as you would at oce • Remotely access your oce network from home • Share Internet connection and printer with multiple computers • No need to dedicate oce space
147D-Link DIR-845L User ManualAppendix A - Wireless BasicsWhere is wireless used? Wireless technology is expanding everywhere not just at home or oce. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coee Shops, Libraries, Restaurants, and Convention Centers.Wireless network is easy to setup, but if you’re installing it for the rst time it could be quite a task not knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.TipsHere are a few things to keep in mind, when you install a wireless network.Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would signicantly reduce any interference that the appliances might cause since they operate on same frequency.Security
148D-Link DIR-845L User ManualAppendix A - Wireless Basics Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-845L wireless network Cardbus adapters.An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate.Wireless Modes
149D-Link DIR-845L User ManualAppendix B - Networking BasicsNetworking BasicsCheck your IP addressAfter you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)At the prompt, type ipcong and press Enter.This will display the IP address, subnet mask, and the default gateway of your adapter.If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some rewall software programs may block a DHCP request on newly installed adapters.
150D-Link DIR-845L User ManualAppendix B - Networking BasicsStatically Assign an IP addressIf you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:Step 1Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center.Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.Windows® XP - Click on Start > Control Panel > Network Connections.Windows® 2000 - From the desktop, right-click My Network Places > Properties.Step 2Right-click on the Local Area Connection which represents your network adapter and select Properties.Step 3Highlight Internet Protocol (TCP/IP) and click Properties.Step 4Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set the Default Gateway the same as the LAN IP address of your router (I.E. 192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.Step 5Click OK twice to save your settings.
151D-Link DIR-845L User ManualAppendix C - Technical SpecicationsTechnical SpecicationsHardware Specications• LAN Interface: Four 10/100/1000Mbps LAN ports• WAN Interface: One 10/100/1000Mbps Internet port• Wireless Interface (2.4Ghz): IEEE 802.11b/g/n• Wireless Interface (5Ghz): IEEE 802.11a/n• USB Interface: Complaint USB 2.0Operating Voltage• Input: 100~240V (±20%), 47~63Hz• Output: DC12V, 2ATemperature• Operating: 32 ~ 104oF (0 ~ 40oC)• Non-Operating: -4 ~ 149oF (-20 ~ 65oC)Humidity• Operating: 10% - 90% non-condensing• Non-Operating: 5% - 95% non-condesingWireless Frequency Range• IEEE 802.11a: 5180 MHz~5240 MHz, 5745 MHz~5825 MHz• IEEE 802.11b: 2400 MHz~2483 MHz• IEEE 802.11g: 2400 MHz~2484 MHz• IEEE 802.11n: 2400 MHz~2484 MHz, 5180 MHz~5240 MHz, 5745 MHz~5825 MHzWireless Bandwidth Rate• IEEE 802.11a: 54, 48, 36, 24, 18, 12, 9, and 6 Mbps• IEEE 802.11b: 11, 5.5, 2, and 1 Mbps• IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9, and 6 Mbps• IEEE 802.11n: 6.5 to 300 MbpsWireless Channel Numbers• IEEE 802.11a: Channels 36~64 and Channels 149~165• IEEE 802.11b: Channels 1~11 (USA), 1~13 (Europe), 1~14 (Japan)• IEEE 802.11g: Channels 1~11 (USA), 1~13 (Europe), 1~14 (Japan)• IEEE 802.11n: Channels 1~11 (USA), 1~13 (Europe), 1~14 (Japan), Channels 36~64 (Channels 149~165 for IEEE 802.11an)Antenna Type• Six Internal Antennas (Two 2.4 GHz Antennas, Two 5 GHz Antennas)Wireless Security• 64/128bit WEP, WPA/WPA2-Personal, WPA/WPA2-Enterprise, WPS (PIN & PBC)Certications• FCC, CE, C-Tick.Dimensions• W=9.9 cm• L=11.9 cm• H=19.15cm Warranty• 2 years
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to indoor environment. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
 !"#$%&'%&'$ ()*"++ #++%&"$,#"'%&"$-'"$".," "////012"34"////012,,.(5,,."$,#"+6"7+38.+ .""9" :,.+ *++ ,";,  ,.7, ,   אՀᤞ፿ᔞش؀᨜چ೴אՀᤞ፿ᔞش؀᨜چ೴אՀᤞ፿ᔞش؀᨜چ೴אՀᤞ፿ᔞش؀᨜چ೴ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽᖲΔॺᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌشृ݁լ൓ᖐ۞᧢ޓ᙮෷ΕףՕפ෷ࢨ᧢ޓ଺๻ૠհ௽ࢤ֗פ౨Ζ܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫٽऄຏॾΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀޏ࿳۟ྤեឫழֱ൓ᤉᥛࠌشΖছႈٽऄຏॾΔਐࠉሽॾऄ๵ࡳ܂ᄐհྤᒵሽຏॾΖ܅פ෷୴᙮ሽᖲႊݴ࠹ٽऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽंᘿ୴ࢤሽᖲ๻ໂհեឫΖ/ /</ =/>12 ૻ৛փࠌشThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Caution : (i) the device for operation in the band 5.15 ~ 5.25GHz / 5.47 ~5.725GHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: Le guide d'utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5.15 ~ 5.25GHz / 5.47 ~5.725GHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l'exploitation point à point et non point à point, selon le cas. (iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipmentshould be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Navigation menu