Fujitsu Client Computing WB0030 Lifebook C Series with WM3B2915ABG 11ABG WLAN & BT User Manual Appendix I 1

Fujitsu Limited Lifebook C Series with WM3B2915ABG 11ABG WLAN & BT Appendix I 1

UserManual.wiki >

Fujitsu Client Computing >

WB0030 User Manual >

users manual 2

FCC ID: EJE-WB0030 (IC: 337J-WB0030) Report No. M050533_Cert_WM3B2915ABG_11abg_DTS_BT This document must not be copied or reproduced, except in full without the written permission of the Manager, EMC Technologies Pty Ltd. The certificate on page 3 may be reproduced in full. www.emctech.com.au APPENDIX H USER MANUAL (PART 2)

33Getting StartedHIBERNATION (SAVE-TO-DISK) FEATUREThe Hibernation feature saves the contents of yourLifeBook notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation FeatureThe default settings is not enabled. To enable or disable the Hibernation feature follow these easy steps:1. From the Start menu, select Settings, and then select Control Panel.2. From the Control Panel select Power Options.3. Select the Hibernation tab. Select the box to enable or disable this feature.Using the Hibernation Feature1. From the Start menu, select Settings, and then select Control Panel.2. From the Control Panel select Power Options.3. Select the Advanced tab. Select Hibernate from the pull down menu for Power buttons.DISPLAY TIMEOUT The Video Timeout is one of the power management parameters. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Power/Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS Setup Utility on page 29 for more information)HARD DISK TIMEOUTThe Hard Disk Timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Power/Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS Setup Utility on page 29 for more information)WINDOWS POWER MANAGEMENT Power ManagementThe Power Management icon located in the Windows Control Panel allows you to configure some power management settings. For example, you can use Power Management to set the timeout values for turning off the display and hard disks whether you are running the notebook on battery power or one of the adapters. The settings may also be changed in the BIOS. (See BIOS Setup Utility on page 29 for more information)RESTARTING THE SYSTEMIf your system is on and you need to restart it, be sure that you use the following procedure. 1. Click the Start button, and then click Shut Down.2. Select the Restart option from within the Windows Shut Down dialog box.3. Click OK to restart your notebook. Your notebook will shut down and then reboot.POWER OFFBefore turning off the power, check that the Hard Drive, optical drive, PC Card, and Floppy Disk indicators are all Off. (See figure 2-3 on page 6). If you power-off while accessing a disk or PC Card there is a risk of data loss. To ensure that the notebook shuts down without error, use the Windows shutdown procedure.Using the correct procedure to shut down from Windows allows your notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:1. Click the Start button, and then click Shut Down or Turn Off Computer.2. Select the Shut Down option from within the Windows Shut Down dialog box.3. Click OK to shut down your notebook.If you are going to store your notebook for a month or more see Care and Maintenance Section. Turning off your notebook without exiting Windows, or turning it on within 10 seconds of being shut off may cause an error when you start the next time. Be sure to close all files, exit all applications, and shut down your operating system prior to turning off the power. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors.E Series.book Page 33 Wednesday, April 14, 2004 10:28 AM

34LifeBook E8000 NotebookE Series.book Page 34 Wednesday, April 14, 2004 10:28 AM

354User-Installable FeaturesE Series.book Page 35 Wednesday, April 14, 2004 10:28 AM

36LifeBook E8000 NotebookE Series.book Page 36 Wednesday, April 14, 2004 10:28 AM

37User Installable FeaturesLithium ion BatteryYour LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.The Lithium ion battery operating time may become shorter if it is used under the following conditions:■When used at temperatures that exceeds a low of 5°C or a high of 35°C. Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indi-cator panel will flash when you try to charge a battery that is outside its operating temperature range. (See Battery Charging Indicators on page 12 for more information)■When using a high current device such as a modem, Super-Multi DVD drive, CD-ROM drive, DVD/CD-RW combo drive, or the hard drive, using the AC adapter will conserve your battery life.RECHARGING THE BATTERIESIf you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook notebook and connect the AC or Auto/Airline adapter.There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your notebook into Suspend mode, or turn it off while the adapter is charging the battery.(See Power Management on page 32 for more information on Suspend mode and shutdown procedure)Low Battery StateWhen the battery is running low, a low battery notifica-tion message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your notebook will go into Suspend mode. There is no guarantee that your data will be saved once the notebook reaches this point.Do not leave a faulty battery in your LifeBook notebook. It may damage your AC adapter, optional Auto/Airline adapter, another battery or your notebook itself. It may also prevent operation of your notebook by draining all available current into the bad battery.■Actual battery life will vary based on screen brightness, applications, fea-tures, power management settings, bat-tery condition and other customer preferences. CD-ROM drive, Super-Multi DVD drive, DVD/CD-RW drive combo, or hard drive usage may also have a significant impact on battery life. The battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one.■Under federal, state, or local law it may be illegal to dispose of batteries by put-ting them in the trash. Please take care of our environment and dispose of bat-teries properly. Check with your local government authority for details regard-ing recycling or disposing of old batter-ies. If you cannot find this information elsewhere, contact your support repre-sentative at 1-800-8FUJITSU (1-800-838-5487)Make sure that the Battery Charging indicator and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel.Using heavy current devices such as Modem or frequent DVD/CD-RW/CD-ROM accesses may prevent charging completely.■Once the low battery notification mes-sage appears, you need to save all your active data and put your LifeBook note-book into Suspend mode until you can provide a new power source. You should provide a charged battery, an AC power adapter, or Auto/Airline adapter as soon as possible.■ When you are in Suspend mode there must always be at least one power source active. If you remove all power sources while your LifeBook notebook is in Suspend mode, any data that has not been saved to the hard drive will be lost.E Series.book Page 37 Wednesday, April 14, 2004 10:28 AM

38LifeBook E8000 NotebookDead Battery Suspend mode shows on the Status indi-cator just like the normal Suspend mode. Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Power/Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your notebook while an adapter is charging the battery.Shorted BatteriesThe Status Indicator panel uses a symbol inside the battery outline of the Battery Level indicator to display the operating level available in that battery. (See figure 2-9 on page 11) If this display shows a Shorted Battery, it means the battery is damaged and must be replaced so it does not damage other parts of your LifeBook notebook.REPLACING THE BATTERY With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. There are two ways to swap batteries, cold-swapping and hot-swapping:Cold-swapping BatteriesTo cold-swap batteries in your battery bay follow these easy steps: (Figure 4-1)1. Have a charged battery ready to install.2. Shut down your notebook and disconnect the AC adapter.3. Unlock the battery bay release latch by pushing the latch release away from the battery pack and sliding the battery bay release latch towards the latch release (Figure 4-1).4. Continue to press the latch release button away from the battery pack, and lift the battery out of the bay by inserting a thumbnail under the edge of the battery at the lift slot.5. Slide a new battery into the bay.6. Slide the battery bay release latch back to its original position to lock the battery into place.8. Plug in the AC adapter and turn the power on. Hot-swapping BatteriesTo hot-swap batteries in your battery bay follow these easy steps: (Figure 4-1)1. Plug an AC Adapter into the system and connect it to a power outlet.Figure 4-1. Removing a Battery2. Follow steps 3 through 5 in “Cold Swapping Batteries”. Be sure to plug in an AC Adapter prior to removing the battery. There is no bridge battery present to support the system while the battery is being replaced. If you do not use an AC Adapter you will lose any unsaved files.If the Lithium ion battery connector is not fully seated, you may not be able to use your notebook or charge your battery.Latch ReleaseBattery Bay Battery PackRelease LatchLift SlotE Series.book Page 38 Wednesday, April 14, 2004 10:28 AM

39User Installable FeaturesFigure 4-2. Optical DriveOptical DriveThere is a variety of media available to use with your system, depending upon the system configuration you have selected. Super-Multi DVD drives, DVD/CD-RW Combo drives, and CD-ROM drives are collectively known as “optical drives”.A CD-R or DVD-R disc can only be written to once; CD-RW or DVD-RW discs can be written to over and over. CD-R and CD-RW discs hold up to 700MB of data. DVD-R and DVD-RW discs hold up to 4.7 GB of data. Depending upon the configuration of your LifeBook notebook, you may have one of the following drives:■Super-Multi DVD: The Super-Multi DVD drive com-bines seven recordable formats in a single drive (DVD-R, DVD+R, DVD-RW, DVD+RW, DVD-RAM, CD-R, and CD-RW), making it the most versatile drive to date.■DVD/CD-RW combo: A DVD/CD-RW combo drive allows you to access movie, software, data, or audio DVD/CDs, and to write data onto recordable CD-R and CD-RW discs.■CD-ROM: A CD-ROM drive allows you to access soft-ware, data, or audio CDs.MEDIA PLAYER SOFTWARESuper-Multi DVD model only: With the Super-Multi DVD drive and media player software you can play DVD movies and music CDs on your LifeBook notebook. The media player includes controls which allow you to take full advantage of the features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc. With this drive you can also burn onto recordable DVD-R/RW, DVD+R/RW, or CD-R/RW discs. DVD/CD-RW Combo model only: With the combo drive, you can play DVD movies, read audio CDs, and write data onto recordable CD-R or CD-RW discs.CD-ROM model only: With the CD-ROM drive, you can read software, audio, or data CD discs.LOADING MEDIA ON YOUR DRIVETo load a disc into your optical drive:1. Push and release the eject button on the front of the optical drive to open the holder tray. The tray will come out of the LifeBook notebook a short distance. 2. Gently pull the tray out until a media disc can easily be placed in the tray.Media Holder TrayMedia Eject ButtonInstall your media player software before first using the DVD, DVD/CD-RW, or CD-ROM media drives. Refer to the applicable readme file on the Driver Applications CD-ROM.■Do not operate your optical drive unless your LifeBook notebook is sitting on a flat surface. Using a drive when the system is not level may damage the drive or prevent proper operation.■Prolonged use of the optical drive, such as watching a DVD movie, will substantially reduce your battery life if no other power source is attached.There may be a protective sheet in the tray from when it was shipped; please make sure it is removed before operating the drive.E Series.book Page 39 Wednesday, April 14, 2004 10:28 AM

40LifeBook E8000 Notebook3. Place the media into the tray, label side up, with the hole in the center of the disc. Snap the disc onto the raised circle in the center of the tray.4. Gently push the holder tray back in until youhear a click. (Figure 4-3)Figure 4-3. Loading/Ejecting MediaREMOVING MEDIA1. Push and release the eject button on the front ofthe optical drive. This will stop the drive and the holder tray will come out of the LifeBook notebook a short distance.2. Gently pull the tray out until the disc can easily be removed from the tray.3. Carefully remove the media disc from the holder tray.4. Gently push the holder tray back in until youhear a click.USING THE MEDIA PLAYER SOFTWAREStarting a DVD Movie (DVD Models only)1. Insert the DVD movie into the optical drive of your notebook. If the CD AutoRun feature activates, skip Step 2. 2. The first time you insert a movie into the DVD/CD-RW tray, you will be prompted to select what you want the system to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will receive the same prompt whenever you insert a disc. 3. Click OK to close the About DVD Player Performance dialog box and the movie will begin.Opening the Media Player Control PanelWith most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the media player control panel and the mouse.1. Right-click on the movie screen to open a dropdown menu for options.2. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen.Using the Media Player Control PanelThe media player software allows you to watch the movie much like a VCR player. You can pause, rewind, fast-forward and stop the movie at any point.1. To Pause the movie, click the on-screen button.2. To Rewind the movie, click the  button to rewind to a specific portion of the movie, or the  button to return to the opening screen.■You should periodically check the Fujitsu web site at us.fujitsu.com/computers for current updated drivers.■All LifeBook DVD players are set to play DVD titles with region code number 1 which is specified for the North American market. The region number is a regional restriction code defined by the DVD Forum acting on Hollywood requirements. Different region codes are recorded on video DVD titles for publication in different areas of the world. If the regional code of the DVD player does not match the regional codes on the titles, then play-back is impossible.■You can change the region code on the DVD player using the Properties menu of the DVD software. Note, however, that you can only change the region code up to four times. After the fourth change, the last region code entered becomes perma-nent, and cannot be changed.If you have disabled the Auto Insert Notification Function, you will have to start the drive from your desktop, since your LifeBook notebook will not automatically recognize that media has been loaded.(a) (b)(c) (d)Depending upon its configuration, your system may not have the media player software pre-installed. If it is not installed, reference the documentation that accompanies the media application.E Series.book Page 40 Wednesday, April 14, 2004 10:28 AM

42LifeBook E8000 NotebookFigure 4-4.Loading/Ejecting a 3.5” Floppy DiskExternal USB Floppy Disk DriveAn external USB floppy disk drive is available as an option for your LifeBook notebook. The external floppy disk drive can read and write information on removable 1.44MB and 720KB floppy disks.LOADING A DISKTo load a disk into your disk drive, follow these easy steps: 1. Orient the disk so that its label is facing upwards and the shutter side is pointing towards the drive. (Figure 4-4)2. Push the disk into the drive until the Eject button pops out and you hear a click. EJECTING A DISKTo eject a disk from the disk drive, follow these easy steps:1. Check that the Floppy Disk Drive Access indicatoris inactive.2. Press the Eject button. This will push your disk partially out of the drive.3. Remove the disk.PREPARING A DISK FOR USEBefore you can use a new disk, it needs to be preparedso your LifeBook notebook knows where to store infor-mation. This preparation is called formatting or initial-izing a disk. You will need to format new disks, unless they are preformatted. (Please refer to your operating system manual for step-by-step instructions on formatting a disk) To prevent accidental erasure of the data stored on a disk, slide the “write protect” tab until a small hole is exposed. This sets the disk into a protected state where nothing can be added or removed. If you want to add or remove data on a protected disk, slide the “write protect” tab to close the small hole. (Figure 4-5)Figure 4-5. Floppy Disk Write ProtectEject ButtonYour LifeBook notebook is preconfigured to boot from a USB floppy drive. Refer-ence the BIOS manual for further informa-tion on changing the default boot drive. The BIOS manual can be found on the Fujitsu Computer Systems web site: us.fujitsu.com/computers, under Support.When there is no disk in the drive, the Eject button is flush with your notebook.If you eject the disk while the Floppy Disk Drive Access indicator is active, there is a risk of damaging the data on the disk, the disk itself or even the disk drive.Formatting a floppy disk that already con-tains data will erase all of the information on the disk.Write ProtectedWrite EnabledE Series.book Page 42 Wednesday, April 14, 2004 10:28 AM

43User Installable FeaturesFigure 4-6. Installing/Removing PC CardsPC CardsYour Fujitsu LifeBook notebook supports two Type I or Type II PC Cards or one Type III PC Card, which can perform a variety of functions. Some available PC Cards:■4-in-1 media card adapter■Compact Flash media card adapter■Fax/data modem cards■Local area network (LAN) cards■IDE solid-state disk cards■SCSI cards■Smart Card holder■Other PC Cards that conform to PCMCIA 2.1 or CardBus standardsFor further information, refer to the instructions supplied with your PC Card.INSTALLING PC CARDSPC Cards are installed in the PC Card slot. To install aPC Card, follow these easy steps: (Figure 4-6) 1. See your PC Card manual for specific instructions on the installation of your card. Some PC Cardsmay require your notebook to be Off whileinstalling them.2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.3. Insert your PC Card into the slot, with the product label facing up. 4. Push the card into the slot firmly until it is seatedin the opening. You will hear a click and the Eject button will pop away from your notebook.5. Flip the Eject button towards the rear of yournotebook to lock the PC Card. REMOVING PC CARDSTo remove a PC Card, follow these easy steps:1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your notebook to be in Suspend Mode or Off while removing them.2. Flip the Eject button towards the front of your note-book until it is fully extended, and then push it in until it is flush with the notebook. This will push the PC Card slightly out of the slot allowing you to remove the card.SMART CARD READERAn embedded Smart Card Reader is provided on your LifeBook notebook. Smart Cards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of different information, and provides the user with many possible options, such as allowing them to make secure purchases, pay for phone calls, store security informa-tion, and provide personal identification and informa-tion. Eject ButtonPC Card SlotsPC Card■Installing or removing a PC Card during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your notebook.■Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently dam-age the card, your LifeBook notebook, or both. ■Be sure to orient the card properly before inserting it. Failure to do so could result in damage to the card socket.If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applica-tions and shut down your notebook. If the PC Card has an external connector and cable, do not pull the cable when removing the card.E Series.book Page 43 Wednesday, April 14, 2004 10:28 AM

44LifeBook E8000 NotebookIn order to use the embedded Smart Card Reader, you must purchase an optional Smart Card adapter and third-party software for installation into an available Type II PC Card slot. E Series.book Page 44 Wednesday, April 14, 2004 10:28 AM

45User Installable FeaturesMemory Upgrade ModuleYour Fujitsu LifeBook notebook comes with a minimum of 256 MB of high speed Double Data Rate Synchronous Dynamic RAM (DDR 333 SDRAM) factory installed. To increase your LifeBook notebook’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at us.fujitsu.com/computers.INSTALLING MEMORY UPGRADE MODULES1. Turn off power to your LifeBook notebook, remove any power adapter (AC or auto/airline), and remove the battery pack.2. Make sure that all the connector covers are closed.3. Turn the notebook bottom side up, and remove the screws of the memory upgrade module compart-ment. (Figure 4-7) 4. Remove the cover.Figure 4-7. Opening the Memory Upgrade Compartment 5. Remove the memory upgrade module from the static guarded sleeve.6. Align the memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. 7. Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is prop-erly in place. (Figure 4-8)Figure 4-8. Installing a Second Memory Module8. Replace the cover.(Figure 4-9)9. Replace the screws.Figure 4-9. Replacing the Memory Compartment CoverTO REMOVE A MEMORY UPGRADE MODULE1. Perform steps 1 through 4 of Installing a Memory Upgrade Module.2. Pull the clips sideways away from each side of the memory upgrade module at the same time. 3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your notebook. (Figure 4-10)Figure 4-10. Removing a Memory Upgrade Module4. Store the memory upgrade module in a static guarded sleeve.5. Replace the cover. (Figure 4-9)6. Replace the screws.■Do not remove any screws from the memory upgrade module compartment except the ones specifically shown in the directions for installing and removing the memory upgrade module.■The memory upgrade module can be severely damaged by electrostatic dis-charge (ESD). Be sure you are properly grounded when handling and installing the module.The memory upgrade module is not something you routinely remove from your notebook. Once it is installed, you can leave it in place unless you want to change system memory capacity.E Series.book Page 45 Wednesday, April 14, 2004 10:28 AM

46LifeBook E8000 NotebookCHECKING THE MEMORY CAPACITYOnce you have changed the system memory capacity by replacing the installed module with a larger one, be sure to check that your notebook has recognized the change.Check the memory capacity by clicking [Start] -> Settings -> Control Panel, then double-clicking the System icon. Select the General tab and check the amount of memory under “Computer:”.There may be a variation between the actual memory size and what is displayed. This is due to the fact that your system uses a video graphics chip which dynami-cally allocates system memory to accelerate graphics performance. Up to 64 MB of memory is dynamically shared on an as-needed basis using Dynamic Video Memory Technology (DVMT).If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is properly installed and the capacity is still not correctly recognized, see Trouble-shooting on page 55.E Series.book Page 46 Wednesday, April 14, 2004 10:28 AM

47User Installable FeaturesFigure 4-11. Port Replicator back panelPort ReplicatorAn optional port replicator is available for your Fujitsu LifeBook notebook. The port replicator extends the functionality of your notebook by providing ports to connect PS/2 devices, a LAN (RJ-45) cable, USB devices, an external monitor, a parallel device, a digital video device, and a serial device. The port replicator connects to the bottom of your notebook. (See Device Ports on page 50 for more information)BACK PANEL COMPONENTSThe following is a brief description of the port repli-cator’s back panel components. (Figure 4-11)LAN (RJ-45) Jack The LAN port allows you to connect a LAN (RJ-45) cable. Note that when your notebook is connected to the port replicator, the LAN port on the system is not acces-sible; the port replicator LAN port is the only one that can be used when it as attached to the system. PS/2 Keyboard/Mouse PortThe PS/2 keyboard/mouse port allows you to connect external PS/2 devices such as an external PS/2 keyboard or mouse. USB PortsThere are four USB 2.0 ports on the port replicator. USB 2.0 ports allow you to connect any USB 2.0 device for up to 480 Mbps transfer rate. USB 2.0 is backward-compat-ible with USB 1.1 devices. External Monitor PortThe external monitor port allows you to connect an external VGA or SVGA CRT monitor. Parallel PortThe parallel port allows you to connect parallel devices. (This is sometimes referred to as an LPT port.) Serial PortThe serial port allows you to connect serial (RS-232C) devices. (This is sometimes referred to as a COM port.) DC Power JackThe DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your note-book. Anti-theft Lock SlotThe anti-theft lock slot allows you to lock the computer into the port replicator or to secure the port replicator alone.Power On/Suspend/Resume ButtonThe power on/suspend/resume button allows you to poer on or suspend/resume your system via the port replicator.Digital Video Interface (DVI-D)The DVI-D port allows you to connect a flat-panel LCD monitor or television that is equipped with a DVI-D port for ultra-crisp digital images and graphics.Port Replicator Release ButtonSlide the port replicator release button to remove the port replicator from your notebook.USB PortsPS/2 PortParallel PortExternal Monitor PortDVI-D PortSerial PortLAN (RJ-45)PortAnti-theft Lock SlotPower On/Suspend/Resume ButtonDC Power JackE Series.book Page 47 Wednesday, April 14, 2004 10:28 AM

48LifeBook E8000 NotebookFigure 4-12. Port Replicator front panelFRONT PANEL COMPONENTSThe following is a brief description of the optional Port Replicator’s front panel components.Interface ConnectorThe interface connector connects the optional port replicator to your notebook. Adjustable Guide BarThe adjustable guide bar allows you to use the port repli-cator with different LifeBook models. Microphone JackThe microphone jack allows you to attach an external microphone via the port replicator.Headphone JackThe headphone jack allows you to connect headphones to the port replicator.Anti-theft Lock SlotThe anti-theft lock slot allows you to secure the port replicator with an optional security lock/cable.ATTACHING THE PORT REPLICATORThe port replicator can be attached to your notebook while the power is on, while in suspend mode, or while the power is off. To attach the port replicator, follow these easy steps:1. Unplug the AC adapter from the system if it is con-nected.2. Depending upon the configuration of your system, you may need to change the position of the adjust-able guide bar. Note the location of the interface port on the bottom of your LifeBook:■ If the interface port is approximately an inch from the edge of the system, swing the guide bar backwards until it rests atop the port replicator base. ■If the interface port is approximately two inches away from the edge of the system, swing the guide bar forward until it snaps into place inside the positioners. (See the grey arrow in Figure 2).3. Center your notebook over the port replicator so that the interface connector on the lower surface of your notebook aligns with the connector on top of the port replicator (Figure 4-13).4. Push your notebook down to connect it securely to the port replicator.5. Plug the AC adapter into the DC power jack and plug the other end into a power outlet.InterfacePort Replicator Release ButtonMicrophone JackHeadphoneAnti-theftLock SlotAdjustable Guide BarJackConnectorDo not hold the system by the port replicator. The port replicator and/or the system could be damaged if the port replicator is used as a handle.The AC adapter must be plugged into the port replicator in order to use all of the ports. If the adapter is connected to the system, the USB and PS/2 ports on the port replicator will not be usable.E Series.book Page 48 Wednesday, April 14, 2004 10:28 AM

49User Installable FeaturesFigure 4-13. Attaching the Port ReplicatorLOCKING THE PORT REPLICATORThere are two anti-theft lock slots on the port replicator: one on the back (Figure 4-11) and one on the end (Figure 4-12). Either slot can be used to secure the port replicator alone. The anti-theft lock slot on the back of the port replicator can also be used to lock the system into the port replicator.Follow the instructions that came with the lock/cable device for information on its use.To lock the system to the port replicator:1. Install the system onto the port replicator as detailed in “Attaching the Port Replicator”.2. Slide the anti-theft lock slot on the rear of the port replicator all the way to the left to lock the system into place (Figure 4-14).3. Secure the lock per the instructions that came with the locking device. Until it is unlocked, the system and port replicator are locked together.Figure 4-14. Locking the Port ReplicatorDETACHING THE PORT REPLICATORThe optional port replicator can be detached from your notebook while the power is on, while in suspend mode, or while the power is off. To detach the port replicator follow these easy steps:1. Unlock the anti-theft lock if the system is locked into place.2. Press the port replicator release button to release the system from the port replicator.3. While holding the port replicator release button down, lift your notebook to detach it from the port replicator. Lock UnlockE Series.book Page 49 Wednesday, April 14, 2004 10:28 AM

50LifeBook E8000 NotebookDevice PortsYour Fujitsu LifeBook notebook and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, modems, printers, etc. MODEM (RJ-11) TELEPHONE JACKThe modem (RJ-11) telephone jack is used for an internal modem. To connect the telephone cable follow these easy steps: 1. Align the connector with the port opening.2. Push the connector into the port until it is seated.3. Plug the other end of the telephone cable into atelephone outlet. (Figure 4-15)Figure 4-15. Connecting a ModemThe modem sound is deactivated by default, to activate modem sound follow these easy steps:1. Right click on the Speaker icon in your system tray.2. Select Open Volume.3. Select Option/Properties.4. Under “Show the following volume controls”, click on Phone and click OK.5. Uncheck the Mute box under Phone Balance.INTERNAL LAN (RJ-45) JACKThe internal LAN (RJ-45) jack is used for a Gigabit (10Base-T/100Base-Tx/1000Base-T/Tx) Ethernet LAN connection. You may need to configure your notebook to work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: 1. Align the connector with the port opening.2. Push the connector into the port until it is seated.(Figure 4-16)3. Plug the other end of the cable into a LAN outlet.Figure 4-16. Connecting the LANPARALLEL PORTThe parallel port, or LPT port, located on the optional Port Replicator allows you to connect parallel devices, such as a printer to your notebook. In order to connect a parallel interface device follow these easy steps: 1. Align the connector with the port opening.2. Push the connector into the port until it is seated.(Figure 4-17)3. Tighten the two hold-down screws, located on each end of the connector. The internal modem is not intended for use with Digital PBX systems. Do not con-nect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook notebook. Consult your PBX manufac-turer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.■The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connec-tion rate depends on the line conditions. The maximum speed is 33600bps at upload. ■The internal modem on all Fujitsu Life-Book notebooks from Fujitsu are certi-fied for use in the United States and Canada. The modem may be certified in other countries.E Series.book Page 50 Wednesday, April 14, 2004 10:28 AM

51User Installable FeaturesFigure 4-17. Connecting a Parallel Device to Port ReplicatorSERIAL PORTThe serial port, or COM port, located on the optional Port Replicator allows you to connect serial devices, such as printers or scanners. In order to connect a serial inter-face device follow these easy steps: 1. Align the connector with the port opening.2. Push the connector into the port until it is seated.3. Tighten the two hold-down screws, located on each end of the connector.PS/2 PORTThe PS/2 port located on the optional Port Replicator allow you to connect an external keyboard or mouse. In order to connect a PS/2 interface device follow these easy steps: 1. Align the connector with the port opening.(Figure 4-18)2. Push the connector into the port until it is seated.Figure 4-18. Connecting a PS/2 DeviceDOCKING PORTThe docking port is used for the connection of your notebook to an optional port replicator or docking station. In order to connect your notebook to one of these devices follow the instructions that came with your docking port. (See figure 2-7 on page 10 for location)UNIVERSAL SERIAL BUS PORTSThe Universal Serial Bus 2.0 ports (USB) allow you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. In order to connect a USB device follow these steps: 1. Align the connector with the port opening.(Figure 4-19)2. Push the connector into the port until it is seated.Figure 4-19. Connecting a USB DeviceINFRARED PORTThe Infrared IrDA (4Mbps) port allows for wireless data transfer between your notebook and other IrDA-compatible devices, such as another computer or a printer, without the use of a cable. (See figure 2-6 on page 9 for location)It is important to keep in mind that while carrying out this form of communication, both devices must be placed so their infrared ports are directly facing each other without obstruction. The devices must also be separated by at least 6" but no more than 36" for maximum performance. The following conditions may interfere with infrared communications:■A television, radio remote control unit, or a wireless headphone is being used nearby.■Direct sunlight, fluorescent light, or incandescent light shines directly on the port.A mouse or keyboard may be installed and automatically recognized by your note-book without restarting or changing set-ups. Due to the ongoing changes in USB tech-nology and standards, not all USB devices and/or drivers are guaranteed to work.■Do not move either device while com-munication is active as it may interrupt data transmission.■Be careful not to scratch the infrared port lens. Dirt, scratches, or other sur-face marks can degrade operation.E Series.book Page 51 Wednesday, April 14, 2004 10:28 AM

52LifeBook E8000 NotebookSTEREO LINE-IN JACKThe stereo line-in jack allows you to connect an external audio source to your notebook, such as an audio cassette player. Your audio device must be equipped with a 1/8" (3.5 mm) stereo mini-plug in order to fit into the stereo line-in jack of your notebook. In order to connect a external audio source follow these easy steps: (See figure 2-6 on page 9 for location)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.IEEE 1394 PORTThe 4-pin 1394 port allows you to connect digital devices that are compliant with IEEE 1394 standard. The IEEE 1394 standard is easy to use, connect, and discon-nect. This port can allow up to 400 Mbps transfer rate. A third-party application may be required to operate your digital device with the 1394 port.In order to connect a 1394 device, follow these steps: 1. Align the connector with the port opening.2. Push the connector into the port until it is seated.(Figure 4-20)Figure 4-20. Connecting an IEEE 1394 DeviceHEADPHONE JACKThe headphone jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect head-phones or speakers follow these easy steps: (See figure 2-5 on page 8 for location)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.MICROPHONE JACKThe microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your notebook. In order to connect a microphone follow these easy steps: (See figure on page 7 for location)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.EXTERNAL MONITOR PORTThe external monitor port allows you to connect an external monitor. In order to connect an external monitor follow these easy steps: (See figure 2-6 on page 9 for loca-tion)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.3. Tighten the two hold-down screws, located oneach end of the connector. Turn down the audio volume when con-necting electronic devices to the line-in jack. The internal speakers might break if unexpected large soundsare inputted.The stereo line-in jack will not support an external microphone.The 1394 port used in this system uses a four-pin configuration. If you intend to interface with devices which use a six-pin configuration, you will need to purchase an adapter.If you plug headphones into the head-phone jack, the built-in stereo speakers will be disabled.Pressing the [Fn] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor.E Series.book Page 52 Wednesday, April 14, 2004 10:28 AM

535TroubleshootingE Series.book Page 53 Wednesday, April 14, 2004 10:28 AM

54LifeBook E8000 NotebookE Series.book Page 54 Wednesday, April 14, 2004 10:28 AM

55TroubleshootingTroubleshootingYour Fujitsu LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.IDENTIFYING THE PROBLEMIf you encounter a problem, go through the following procedure before pursuing complex troubleshooting:1. Turn off your LifeBook notebook.2. Make sure the AC adapter is plugged into your note-book and to an active AC power source.3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5. Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it back on.6. Go through the boot sequence.7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. 8. If you have tried the solutions suggested in the Trou-bleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.com Web site: us.fujitsu.com/computers.Before you place the call, you should have the following information ready so that the customer support represen-tative can provide you with the fastest possible solution:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Hardware configuration■Type of device connected, if anySee the Configuration Label on the bottom of yournotebook for configuration and serial numbers. (See figure 2-7 on page 10 for location)SPECIFIC PROBLEMSUsing the Troubleshooting TableWhen you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone.E Series.book Page 55 Wednesday, April 14, 2004 10:28 AM

56LifeBook E8000 NotebookTROUBLESHOOTING TABLEProblem PageAudio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 56DVD/CD-ROM Drive Problems. . . . . . . . . . . . . page 56Port Replicator Problems. . . . . . . . . . . . . . . . . . . page 57Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 57Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 57Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 58Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 58Problem PageModem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 58Parallel, Serial and USB Device Problems . . . . . page 58PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 59Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 59Shutdown and Startup Problems . . . . . . . . . . . . page 61Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 62Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 63Problem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speakers.The volume is turned too low. Adjust the volume control on your notebook.The software volume control is set too low.Adjust the sound volume control settings in your software, operating system and applications.Headphones are plugged into your notebook.Plugging in headphones disables the built-in speakers, remove the headphones.BIOS audio settingsare incorrect.Set the BIOS setup utility to the default values within the Multimedia Device Configuration menu. (See BIOS Setup Utility on page 29 for more information)Software driver is not configured correctly.Refer to your application and operating system documentation for help.The speakers have been muted using the Volume icon in the system tray.Click on the Volume icon in the tool tray on the bottom right of the screen. (It looks like a speaker). If the Mute box is checked, click on it to uncheck it.DVD/CD-RW/CD-ROM Drive ProblemsLifeBook notebook fails to recognize DVD/CD-RW/CD-ROM’s.Protective sheet is still in the DVD/CD-RW/CD-ROMdrive tray.Replace DVD/CD-RW/CD-ROM in tray.DVD/CD-RW/CD-ROM is not pushed down onto raised center circle of the drive.Open DVD/CD-RW/CD-ROM tray and re-install DVD/CD-RW/CD-ROM properly.DVD/CD-RW/CD-ROM tray is not latched shut.Push on the front of the DVD/CD-RW/CD-ROM tray until it latches.Incorrect DVD Player or no DVD Player software is installed.Install DVD Player software. (See “Media Player Software” on page 39 for more information.)Wrong drive designator was used for DVD/CD-RW/CD-ROM in the application.Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/CD, drive designations are automatically adjusted. Note that the drive designation can be changed with the Disk Management tool located at Administrative Tools -> Computer Managenment.E Series.book Page 56 Wednesday, April 14, 2004 10:28 AM

57TroubleshootingLifeBook notebook fails to recognize DVD/CD-RW/CD-ROM’s (continued)Windows DVD/CD-RW/CD-ROM auto insertion function is disabled.Start the DVD/CD-RW/CD-ROM from the desktop or application software or re-enable the Windows DVD/CD-RW/CD-ROM auto insertion function. LifeBook notebook fails to recognize DVD/CD-RW/CD-ROM’s. DVD/CD-RW/CD-ROM is dirty or defective.Wipe DVD/CD-RW/CD-ROM with a non-abrasive CD cleaning cloth and reinsert. It if still will not work try another DVD/CD-RW/CD-ROM inthe drive.The DVD/CD-RW/CD-ROM Access indicator on the Status Indicator Panel blinks at regular intervals when no DVD/CD-RW/CD-ROM is in the tray or the DVD/CD-RW/CD-ROM drive is not installed.The Windows DVD/CD-RW/CD-ROM auto insertion func-tion is active and is checking to see if a DVD/CD-RW/CD-ROM is ready to run. This is normal. However, you may disable this feature. Port Replicator ProblemsNote: Be sure to power down your LifeBook notebook before adding a printer to the Port Replicator parallel port.LifeBook notebook does not turn on when installed in the optional Port ReplicatorPort Replicator AC adapter is not plugged in.Provide power to the Port Replicator.Notebook is not properly seated in the Port Replicator.Remove and re-dock your LifeBook notebook.Floppy Disk Drive ProblemsYou cannot access your floppy disk.You tried to write to a write protected floppy disk.Eject the floppy disk and set it to write enable. (See Preparing a Disk for Use on page 42 for more information)Floppy disk is not loaded correctly.Eject floppy disk, check orientation and re-insert. (See Ejecting a Disk on page 42 for more information)The floppy disk drive may not be properly installed.Remove and re-install your floppy disk drive. Security is set to protect access to floppy disk data.Verify your password and security settings.Hard Drive ProblemsYou cannot access your hard drive.The setup utility is incorrectly set for your internal (Primary Master) or optional second hard drive (Primary Slave).Revise BIOS settings to set both Primary Masterand Primary Slave correctly. (See BIOS Setup Utility on page 29 for more information)The wrong drive designator was used by an application when a bootable CD-ROM was used to start the notebook.Verify drive designator used by application is inuse by the operating system. When the operating system is booted from a CD, drive designationsare automatically adjusted. Security is set so your oper-ating system cannot be started without a password.Verify your password and security settings.Problem Possible Cause Possible SolutionsE Series.book Page 57 Wednesday, April 14, 2004 10:28 AM

58LifeBook E8000 NotebookKeyboard or Mouse ProblemsThe built-in keyboard does not seem to work.The notebook has gone into Suspend mode.Push the Power/Suspend/Resume button.Your application has locked out your keyboard.Try to use your integrated pointing device to restart your system. You have installed an external keyboard or mouse, and it does not seem to work.Your external device is not properly installed.Re-install your device. (See Device Ports on page 50 for more information)Your operating system software is not setup with the correct software driver for that device.Check your device and operating system docu-mentation and activate the proper driver.Your mouse or keyboard is connected to the wrong PS/2 port on the optional Port Replicator.Plug the mouse into the PS/2 Mouse port and the external keyboard or numeric key pad into the PS/2 Keyboard port. (See PS/2 Port on page 51 for more information)You have connected an external keyboard or a mouse and it seems to be locking up the system.Your operating system software is not setup with the correct software driver for that device.Check your device and operating systemdocumentation and activate the proper driver.Your system has crashed. Try to restart your notebook. IMemory ProblemsYour Power On screen, or Main menu of the BIOS setup utility information, does not show the correct amount of installed memory.Your memory upgrade module is not properly installed.Remove and re-install your memory upgrade module. (See Memory Upgrade Module on page 45 for more information)You have a memory failure. Check for Power On Self Test (POST) messages. (See Power On Self Test Messages on page 64 for more information)Modem ProblemsMessages about modem operation.Messages about modem operation are generated by whichever modem application is in use.See your application software documentation for additional information.Parallel, Serial, and USB Device ProblemsYou have installed a parallel port device, a serial port device or a USB device. Your LifeBook notebook does not recognize the device, or the device does not seem to work properly.The device is not properly installed.Remove and re-install the device. (See Device Ports on page 50 for more information)The device may have been installed while an application was running, so your notebook is not aware of its installation.Close the application and restart your notebook.Your device may not have the correct software driver active.See your software documentation and activate the correct driver.You may have the wrong I/O address selected for your device.See your device documentation and software docu-mentation to determine the required I/O address. Change the settings in the BIOS setup utility. (See BIOS Setup Utility on page 29 for more information)Problem Possible Cause Possible SolutionsE Series.book Page 58 Wednesday, April 14, 2004 10:28 AM

59TroubleshootingYou have installed a parallel port device, a serial port device or a USB device. Your LifeBook notebook does not recognize the device, or the device does not seem to work properly.(continued)Your device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.Parallel port is set to output only.Check parallel port setting in the BIOS and set tobi-directional or ECP.PC Card ProblemsA card inserted in the PC Card slot does not work or is locking up the system.The card is not properly installed.Remove and re-install the card. (See PC Cards on page 43 for more information)The card may have been installed while an application was running, so your notebook is not aware of its installation.Close the application and restart your notebook.Your software may not have the correct software driver active.See your software documentation and activate the correct driver.You may have the wrong I/O address selected for your PC Card device.See your PC Card documentation to determinethe required I/O address. Change the settings inthe BIOS. (See BIOS Setup Utility on page 29 for more information)Your PC Card device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.Power FailuresYou turn on your LifeBook notebook and nothing seems to happen.The installed primary battery is completely discharged, there is no optional second battery installed or there is no Power adapter (AC or Auto/Airline) installed.Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 11 for more information) Install a charged battery or a Power adapter.The primary battery is installed but is faulty.Use the Status Indicator panel to verify the presence and condition of the batteries. (See Status Indicator Panel on page 11 for more information) If a battery is indicating a short, remove that battery and operate from another power source or replace that battery.The battery or batteries are low. Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 11 for more information) Use a Power adapter to operate until a battery is charged or install a charged battery.The power adapter (AC or auto/airline) is not pluggedin properly.Verify that your adapter is connected correctly. (See Power Sources on page 27 for more information)Problem Possible Cause Possible SolutionsE Series.book Page 59 Wednesday, April 14, 2004 10:28 AM

60LifeBook E8000 NotebookYou turn on your LifeBook notebook and nothing seems to happen.(continued)The Power adapter (AC or auto/airline) has no power from the AC outlet, airplane seat jack, or the car’s cigarette lighter.Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.The Power adapter (AC or auto/airline) is faulty.Try a different Power adapter or install a charged optional second battery.Your LifeBook notebook turns off all by itself.The power management parameters are set for auto timeouts which are too short for your operating needs.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your needs.You are operating on battery power only and have ignored a low battery alarm until the batteries are all at the dead battery state and your machine has gone into Dead Battery Suspend mode.Install a power adapter and then push the Power/Suspend/Resume button. (See Power Sources on page 27 for more information)You have a battery failure. Verify the condition of the batteries using theStatus Indicator panel, and replace or removeany batteries that are shorted. (See Status Indicator Panel on page 11 for more information)Your power adapter has failed or lost its power source.Make sure the adapter is plugged in and the outlet has power.Your LifeBook notebook will not work on battery alone.The installed batteries are dead.Replace the battery with a charged one or install a Power adapter.No batteries are installed. Install a charged battery.The batteries are improperly installed.Verify that the batteries are properly connected by re-installing them.Your installed batteriesare faulty.Verify the condition of the batteries using theStatus Indicator panel and replace or removeany batteries that are shorted. (See Status Indicator Panel on page 11 for more information)The batteries seem to discharge too quickly.You are running an application that uses a great deal of power due to frequent hard drive access or DVD/CD-ROM access, use of a modem cardor a LAN PC card.Use both the primary battery and an optional second battery and/or use a power adapter for this application when at all possible.The power savings features may be disabled.Check the power management and/or setup utility settings in the Power Savings menu and adjust according to your operating needs.The brightness is turned all the way up.Turn down the brightness adjustment. The higher the brightness the more power your display uses.The batteries are very old. Replace the batteries.Problem Possible Cause Possible SolutionsE Series.book Page 60 Wednesday, April 14, 2004 10:28 AM

62LifeBook E8000 NotebookVideo ProblemsThe built-in display is blank when you turn on your LifeBook notebook.Something is pushing on the Closed Cover switch. Clear the Closed Cover switch. (See figure 2-3 on page 6 for location)The notebook is set for an external monitor only.Pressing [F10] while holding down the [Fn] key allows you to change your selection of where tosend your display video. Each time you press the combination of keys you will step to the nextchoice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.The angle of the display and the brightness settings are not adequate for your lighting conditions.Move the display and the brightness control until you have adequate visibility.The power management time-outs may be set for very short intervals and you failed to notice the display come onand go off again.Press any button the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Standy mode, Auto Suspend or Video Timeout)The LifeBook notebook turned on with a series of beeps and your built-in display is blank.Power On Self Test (POST)has detected a failure which does not allow the displayto operate. Contact your support representative.The display goes blank by itself after you have been using it.The notebook has gone into Video timeout, Standby mode, Suspend mode or Save-to-Disk mode because you have not used it for a period of time.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on page 29 for more information)The power management time-outs may be set for very short intervals and you failed to notice the display come onand go off again.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)Something is pushing on the Closed Cover switch.Check the Closed Cover switch. (See figure 2-3 on page 6 for location)Your system display won’t turn on when the system is turned on or when the system has resumed.The system may be password-protected.Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.The Built-in Display does not close.A foreign object, such as a paper clip, is stuck between the display and the keyboard.Remove all foreign objects from the keyboard.Problem Possible Cause Possible SolutionsE Series.book Page 62 Wednesday, April 14, 2004 10:28 AM

63TroubleshootingThe Built-in Display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.Display is faulty; contact your support representative.The application display uses only a portion of your screen and is surrounded by a dark frame.You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compres-sion is enabled.Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing your display compression setting, (See the Video Features submenu, located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 29 for more information)The Display is dark when on battery power.The Power Management utility default is set on low brightness to conserve power.Press [Fn] + [F7] to increase brightness or double-click on the battery gauge and adjust Power Control under battery settings.You have connected an external monitor andit does not displayany information.Your BIOS setup is not set to enable your external monitor.Try toggling the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on page 29 for more information)Your external monitor is not properly installed. Reinstall your device. (See External Monitor Port on page 52 for more information)Your operating system soft-ware is not setup with the correct software driver forthat device. Check your device and operating systemdocumentation and activate the proper driver.You have connected an external monitor and it does not come on.Your external monitor is not compatible with your LifeBook notebook.See your monitor documentation and theExternal Monitor Support portions of theSpecifications section. (See Specifications on page 77 for more information)Miscellaneous ProblemsAn error message is displayed on the screen during the operation ofan application.Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible SolutionsE Series.book Page 63 Wednesday, April 14, 2004 10:28 AM

64LifeBook E8000 NotebookPOWER ON SELF TEST MESSAGESThe following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)*Diskette drive A error or Diskette drive B error Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 29 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.*Extended RAM Failed at offset: nnnn Extended memory not working or not configured prop-erly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is prop-erly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.nnnn Extended RAM Passed Where nnnn is the amount of memory in kilobytes successfully tested.*Failing Bits: nnnn The hex number nnnnThis is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4) The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.*Incorrect Drive A type – run SETUP Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.*Incorrect Drive B type – run SETUPType of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.*Invalid NVRAM media typeProblem with NVRAM access. In the unlikely case that you see this message you may have some display prob-lems. You can continue operating but should contact your support representative for more information.*Keyboard controller error The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Keyboard error Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able touse an external keyboard until then. Contact your support representative.*Keyboard error nn BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.*Monitor type does not match CMOS – Run SETUPMonitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted.*Parity Check 1 nnnn Parity error found in the system bus. BIOS attemptsto locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is apotentially data destroying failure. Contact yoursupport representative.E Series.book Page 64 Wednesday, April 14, 2004 10:28 AM

65Troubleshooting*Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is apotentially data-destroying failure. Contact yoursupport representative.*Press <F1> to resume, <F2> to SETUP Displayed after any recoverable error message. Pressthe [F1] key to continue the boot process or the [F2]key to enter Setup and change any settings.*Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete success-fully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.*Real time clock error Real-time clock fails BIOS test. May require board repair. Contact your support representative.*Shadow RAM Failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corrup-tion if you continue. Contact your support representative.nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested.*System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your notebook. This battery has an expected life of 2 to 3 years.System BIOS shadowed System BIOS copied to shadow RAM.*System CMOS checksum bad – run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.*System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.nnnn System RAM PassedWhere nnnn is the amount of system memory inkilobytes successfully tested.*System timer error The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.Video BIOS shadowed Video BIOS successfully copied to shadow RAM.EMERGENCY MEDIA PLAYER DRIVE TRAY RELEASEIf for some reason the eject button fails, you can open the DVD/CD-ROM tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clipand push it gently into the hole. The tray will pop outa short distance.MODEM RESULT CODESThe operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are:■OK■NO CARRIER■NO DIALTONE■CONNECT 53000 (Connection complete at 53,000 bps.)■ERROR■FAX■RING (This means an incoming call.)■BUSY■NO ANSWERWhen using the internal modem with applicationsthat are not factory installed refer to theapplication documentation.E Series.book Page 65 Wednesday, April 14, 2004 10:28 AM

$66LifeBook E8000 NotebookRESTORING YOUR PRE-INSTALLED SOFTWAREThe Drivers and Applications Restore (DAR) CD contains:■Sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your LifeBook note-book configuration for use as documented below.■A link to the Drive Image Special Edition (DISE) utility on your hard disk drive.■Read-me files that provide additional use information for items on this CD-ROM.DRIVE IMAGE SPECIAL EDITION (DISE)PowerQuest Drive Image Special Edition (DISE) provides a way to restore your computer if you experi-ence a hard disk crash or other system failure. Fujitsu has used DISE to create an image of everything installed on the computer at the time you purchased it. The image is saved on a separate partition on the hard disk. You can use DISE to restore the factory image and return your computer to the state in which it was shipped from Fujitsu.Although it is not necessary, you can use DISE to store additional image files that you create. For example, if you install several applications and save data files on your hard disk, you can create a new image file that includes them and then save that image file on the hard disk. Then, in the event of a hard disk failure, you can restore the image that includes the applications and data files you use.Creating a Backup ImageYou can create a backup image of your C:\ drive at any time. The C:\ partition must be a FAT, FAT32, or NTFS partition, and it must be directly before the backup partition on your hard disk.There are two ways to implement the DISE utility: When booting up the system, or from the desktop. Creating a backup image when booting upBefore creating a backup image at boot-up, you must first change the boot-up priority in the BIOS so that the system will go to the CD drive first, rather than trying to boot-up from the hard drive or an external floppy disk drive.To change the boot-up priority:1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.2. Using the arrow keys, go to the Boot menu.3. Arrow down to the Boot Device Priority submenu and press [Enter].4. Arrow down to the CD-ROM drive in the list, and press the space bar (or the + key) to move the CD-ROM drive to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.)5. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.After you have changed the boot priority, you can create a backup image when you are booting up:1. Install the DAR CD in the drive prior to booting up. When bootup begins, a message will appear informing you that continuing to boot from the CD will overwrite all information on the hard drive, including saved files, and restore the hard drive to its factory configuration. 2. When you are asked if you want to restore the factory image, click [Y]es.Creating a backup image from the desktopTo create a backup image from the desktop, select Drive Image SE from the Program list. You will initially be prompted to create a backup diskette. It is not necessary to create the backup diskette, since the DAR CD performs the same function.1. At the Drive Image Special Edition main screen, click Options> Create New Backup. DISE displays a warning that it must go to DOS to create the image.3. Click Yes .DISE creates an image file in the backup partition. If you created a backup image previously, the new image overwrites the old one.If the DAR CD is in the drive when you boot up the system, a message will appear informing you that continuing to boot from the CD will overwrite all information on the hard drive, including saved files, and restore the hard drive to its factory configuration. If you wish to install drivers or applications only from the CD, remove the disk from the drive, reboot the system, and insert the CD after Windows has started.If you have access to the internet, visit the Fujitsu Support web site at us.fujitsu.com/computers to check for the most current information, drivers and hints on how to perform recovery and system updates.Using the DISE feature will reduce the amount of usable disk space on your hard disk drive.E Series.book Page 66 Wednesday, April 14, 2004 10:28 AM$

$67TroubleshootingEnlarging the Backup PartitionIf there is not enough unused space in the backup parti-tion on your hard disk, DISE will resize the partition. DISE will display the minimum, maximum, and recom-mended sizes for the backup partition. You choose the size you want.DISE takes the space from the FAT, FAT32, or NTFS partition that you are backing up. If there is not enough unused space in that partition to take, you will not be able to resize the backup partition and create an image file. You can delete files from the FAT, FAT32, or NTFS partition to create more unused space on the hard disk.Restoring a Backup ImageYou can restore either a factory image or a backup image you created. Be aware that restoring a backup image will replace the contents of the C:\ partition with the image you restore.1. Disable virus protection software. If virus protection software is enabled, DISE will hang.2. From the DISE main window, click Options > Restore Backup to restore an image you created, or click Options > Restore Factory Backup to restore the factory image.DISE shuts down to DOS and restores the image file.Re-Installing Individual Drivers and Applications The Drivers and Application CD can be used to selec-tively re-install drivers and/or applications that may have been un-installed or corrupted. To re-install drivers and/or applications:1. Boot up the system and insert the DAR CD after Windows has started. The LifeBook Easy Installation screen appears. 2. Select the drivers and applications you want to install from the list that is displayed.3. Click [Start]. Follow the prompts that appear to complete installation of the selected drivers and/or applications.AUTOMATICALLY DOWNLOADING DRIVER UPDATESYour system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system.The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the FDU icon does not appear in the system tray, it can be started by going to [Start] -> All Programs, and clicking on Fujitsu Driver Update; this will create the icon automatically.To invoke the FDU menu, you can either right-click on the FDU icon or hold the pen on the icon for a couple of seconds until the menu appears. The menu contains the following items:■Check for updates nowAllows for manual driver update search. The first time it is used, you are prompted to agree to a user agreement. After clicking on the icon, the FDU auto-matically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you of the fact.■Enable Automatic Update NotificationsAutomatically searches for new updates on a regular basis (approximately every 3 days).■Show update historyBrings up a screen that displays a history of updates that have been made via the FDU.■About Fujitsu Driver UpdateDisplays the FDU version number and copyright information■Fujitsu Driver Update ReadmeDisplays the FDU readme.E Series.book Page 67 Wednesday, April 14, 2004 10:28 AM$

Fujitsu Client Computing WB0030 Lifebook C Series with WM3B2915ABG 11ABG WLAN & BT User Manual Appendix I 1

Fujitsu Limited Lifebook C Series with WM3B2915ABG 11ABG WLAN & BT Appendix I 1

Contents

users manual 2

Navigation menu

Namespaces

Views

Navigation