Honeywell LXE4830P 802.11g Compact Flash Module User Manual HX2 User s Guide

Honeywell International, Inc. 802.11g Compact Flash Module HX2 User s Guide

User Manual HX2

HX2 User’s Guide (Microsoft® Windows® CE 5.0 Equipped) FOR Approvals REVIEW – DO NOT PUBLISH OR DISTRIBUTE – LXE CONFIDENTIAL – DRAFT 09 / Approvals – Copyright © 2007 by LXE Inc. All Rights Reserved E-EQ-HX2OGWW-A For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Language: English Notices LXE Inc. reserves the right to make improvements or changes in the products described in this guide at any time without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, LXE assumes no liability resulting from any errors or omissions in this document, or from the use of the information contained herein. Further, LXE Incorporated, reserves the right to revise this publication and to make changes to it from time to time without any obligation to notify any person or organization of such revision or changes. Copyright: This document is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form without prior consent, in writing, from LXE Inc. Copyright © 2007 by LXE Inc. An EMS Technologies Company. 125 Technology Parkway, Norcross, GA 30092 U.S.A. (770) 447-4224 Trademarks: LXE® and Spire® are registered trademarks of LXE Inc. RFTerm® is a registered trademark of EMS Technologies Company. Summit Data Communications, the Summit logo, and “The Pinnacle of Performance” are trademarks of Summit Data Communications, Inc. Microsoft®, Windows® and the Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries. Symbol® is a registered trademark of Symbol Technologies. MOTOROLA® and the Stylized M Logo are registered trademarks of Motorola®, Inc. Java® and Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. or other countries, and are used under license. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is under license. RAM® and RAM Mount™ are both trademarks of National Products Inc., 1205 S. Orr Street, Seattle, WA 98108. Wavelink®, the Wavelink logo and tagline, Wavelink Studio™, Avalanche Management Console™, Mobile Manager™, and Mobile Manager Enterprise™ are trademarks of Wavelink Corporation, Kirkland. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. When this document is in PDF format: “Acrobat ® Reader Copyright © 2007 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated.” Applies. The user is strongly encouraged to read Appendix B - Regulatory Notices and Safety Information. Important safety cautions, warnings and worldwide regulatory agency information is contained in Appendix B. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Table of Contents INTRODUCTION 1 Overview ................................................................................................................................................. 1 Ring Scanner Warnings and Labels .................................................................................................... 2 Important Battery Information .............................................................................................................. 3 Environmental Specifications .............................................................................................................. 4 HX2.......................................................................................................................................................................4 Lithium Ion Battery Pack......................................................................................................................................4 Document Conventions......................................................................................................................... 5 Getting Help............................................................................................................................................ 6 Manuals.................................................................................................................................................................6 Accessories ...........................................................................................................................................................6 COMPONENTS 9 Front ...................................................................................................................................................... 10 Back....................................................................................................................................................... 11 Left Arm Use ......................................................................................................................................................11 Right Arm Use ....................................................................................................................................................11 Connectors ........................................................................................................................................... 12 Ring Scanner / Audio / Battery Connection........................................................................................................12 Cradle Connection...............................................................................................................................................12 Tethered Ring Scanner / Imager......................................................................................................... 13 Cables ................................................................................................................................................... 14 Li-Ion Battery........................................................................................................................................ 15 Standard Battery..................................................................................................................................................15 Extended Battery.................................................................................................................................................15 Mounting Bracket Clips....................................................................................................................... 16 Mounting Devices ................................................................................................................................ 17 Armband .............................................................................................................................................................17 Straps................................................................................................................................................................17 Hip Flip ...............................................................................................................................................................18 QUICK START 19 Getting Started ..................................................................................................................................... 19 Pre-requisites.......................................................................................................................................................19 HX2 Quick Start .................................................................................................................................................19 Wearable Device Assembly ................................................................................................................................20 Armband...........................................................................................................................................................20 Hip Flip ............................................................................................................................................................21 Ring Scanner Strap...........................................................................................................................................21 Connecting the Battery and Ring Scanner........................................................................................ 22 Ring Scanner on the Left Hand...........................................................................................................................22 Ring Scanner on the Right Hand.........................................................................................................................22 Connecting the Audio Cable and a Headset ..................................................................................... 23 Adjust Microphone and Secure the Cable...........................................................................................................23 Tapping the Power Key ....................................................................................................................... 24 Tapping the Touchscreen with a Stylus ............................................................................................ 24 Calibrating the Touchscreen .............................................................................................................. 24 Power Key Functions .......................................................................................................................... 25 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
ii Table of Contents HX2 User’s Guide E-EQ-HX2OGWW-A Hardware Reset...................................................................................................................................................25 Warm Boot..........................................................................................................................................................25 Cold Boot............................................................................................................................................................25 Using the 23 Key Keypad.................................................................................................................... 26 Inserting Characters Using the Input Panel.........................................................................................................26 System Status LEDS............................................................................................................................ 27 Entering Data........................................................................................................................................ 28 Keypad Entry ......................................................................................................................................................28 Stylus Data Entry ................................................................................................................................................28 Ring Scanner Data Entry.....................................................................................................................................29 Laser Scanner...................................................................................................................................................29 2D Imager ........................................................................................................................................................29 Scan Status LED ..............................................................................................................................................30 Voice Data ..........................................................................................................................................................30 Input Panel / Virtual Keyboard ...........................................................................................................................31 Bluetooth Devices................................................................................................................................ 32 Checking Battery Status ..................................................................................................................... 32 Entering the Multi AppLock Activation Key...................................................................................... 33 Application Switching Activation Key ...............................................................................................................33 Touch ..................................................................................................................................................................33 Setting the Power Schemes Timers................................................................................................... 34 Battery Power Scheme........................................................................................................................................34 AC Power Scheme ..............................................................................................................................................34 Setting The Audio Speaker Volume ................................................................................................... 35 Using the Keypad................................................................................................................................................35 Using the Touchscreen........................................................................................................................................35 Adjusting the Display Backlight Timer .............................................................................................. 36 Turning the Keypad Backlight On or Off ........................................................................................... 37 Cleaning the Glass Display/Ring Scanner Aperture ........................................................................ 37 OPTIONAL EQUIPMENT 39 HX2 Rubber Boot Assembly ............................................................................................................... 39 Protective Film for the Screen Display .............................................................................................. 39 HX2 Voice Case Assembly.................................................................................................................. 40 Removing/Replacing the Armband Straps........................................................................................ 41 HX2 Docking/Charging Cradle............................................................................................................ 43 Cradle LEDs........................................................................................................................................................44 HX2 Docked/Receiving Power LED ...............................................................................................................44 Left and Right Battery Charging LED .............................................................................................................44 HX2 Multi-Charger................................................................................................................................ 45 Charging Pocket LED .........................................................................................................................................45 Charger/Analyzer LEDs......................................................................................................................................46 APPENDIX A KEY MAPS 47 23 Key Keypad ..................................................................................................................................... 47 APPENDIX B REGULATORY NOTICES AND SAFETY INFORMATION 51 HX2 Approvals/Standards................................................................................................................... 52 Laser Light Class 2 Labels – Ring Scanners .................................................................................... 56 Laser Light Class 2 Labels – Bluetooth Scanners ........................................................................... 56 INDEX 57 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Table of Contents iii E-EQ-HX2OGWW-A HX2 User’s Guide Illustrations Figure 1 Ring Scanner Caution Label – Class 2 Laser Scanner...........................................................................2 Figure 2 Front ....................................................................................................................................................10 Figure 3 Back.....................................................................................................................................................11 Figure 4 Scanner / Audio / Battery Ports – Connector 1 and 2 ..........................................................................12 Figure 5 Cradle/Power Port – Connector 3 (Base).............................................................................................12 Figure 6 Laser Ring Scanner..............................................................................................................................13 Figure 7 Imager Ring Scanner ...........................................................................................................................13 Figure 8 Concept - Ring Scanner Hook and Loop Strap...................................................................................13 Figure 9 Ring Scanner/Imager Apertures...........................................................................................................13 Figure 10 Cable – Battery and HX2 Connectors................................................................................................14 Figure 11 Cable – Audio, Battery and HX2 Connectors....................................................................................14 Figure 12 Cable – Laser Ring Scanner and HX2 Connectors ............................................................................14 Figure 13 Cable – Imager Ring Scanner and HX2 Connectors..........................................................................14 Figure 14 HX2 Standard and HX2 Extended Battery ........................................................................................15 Figure 15 Mounting Brackets.............................................................................................................................16 Figure 16 Armband and Hip Flip Mount Assembly and Clips ..........................................................................16 Figure 17 Armband / Top and Bottom...............................................................................................................17 Figure 18 Armband Straps .................................................................................................................................17 Figure 19 Hip Flip and Belt ...............................................................................................................................18 Figure 20 HX2 Armband, Left Arm Orientation, Ring Scanner, Audio ............................................................20 Figure 21 HX2 Hip Flip, Audio .........................................................................................................................21 Figure 22 Tether the Battery and Ring Scanner – Left / Right...........................................................................22 Figure 23 Audio Cable and Headset ..................................................................................................................23 Figure 24 The 23 Key Keypad...........................................................................................................................26 Figure 25 System Status LEDs ..........................................................................................................................27 Figure 26 Laser Scan Beam on Linear Barcode.................................................................................................29 Figure 27 Imager Bracketed Crosshair Target on 2D Barcode ..........................................................................29 Figure 28 Concept - Scan Status LED ...............................................................................................................30 Figure 29 Input Panel / Virtual Keyboard..........................................................................................................31 Figure 30 AppLock – How to Switch Applications ...........................................................................................33 Figure 31 Power Properties – Schemes Tab.......................................................................................................34 Figure 32 Volume & Sounds Properties ............................................................................................................35 Figure 33 Setting the Display Backlight Timer..................................................................................................36 Figure 34 Turning the Keypad Backlight On or Off..........................................................................................37 Figure 35 HX2 Rubber Boot..............................................................................................................................39 Figure 36 HX2 Voice Case ................................................................................................................................40 Figure 37 Removing/Replacing the Armband Straps.........................................................................................41 Figure 38 Armband Straps .................................................................................................................................41 Figure 39 Concept – An HX2, Two Batteries and 1 Ring Scanner in Cradle ....................................................43 Figure 40 Concept - Powered Cradle LEDs.......................................................................................................44 Figure 41 HX2 Multi-Charger ...........................................................................................................................45 Figure 42 Multi-Charger Control Panel .............................................................................................................46 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
iv Table of Contents HX2 User’s Guide E-EQ-HX2OGWW-A For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Introduction Overview The LXE® HX2 is a small, lightweight mobile computer designed to be worn on a person’s arm or waist. The HX2 is most useful for applications that require computational support while the user's hands are actively engaged with the physical environment, including piece picking to carts, containers or conveyers; case picking; parcel moves; and broken case activities. The armbands that secure both the unit and its battery keeps the HX2 in the ready position at all times by preventing the unit from rotating around the wearer’s arm. The adaptable armbands can be worn close to the elbow or near the wrist. The primary data inputs are a keypad or a ring scanner. The HX2 is voice ready. Voice can also be used as an input with 3rd party software. Output is presented using the screen display or audio feedback generated by the mobile device and delivered through an internal speaker or audio headset. The HX2 is powered by a tethered low profile, light and unobtrusive battery. The entire HX2 wearable computer system features breakaway connections at multiple points and a low-profile, smooth design to resist snagging on common warehouse fixtures and equipment. The HX2 has a Microsoft® Windows® CE 5.0 operating system with an Intel® XScale® PXA255 CPU. The HX2 supports an 802.11b/g WLAN radio and Bluetooth® 2.0+EDR radio. Connectors are available which interface with peripherals such as a Ring Scanner (1D Laser and 2D Imager Ring Scanner), an audio headset, a docking/charging cradle and a tethered battery (see Components for port locations). The QVGA color display with a touch panel has a diagonal viewing area of 2.5” (6.3 cm) in landscape orientation. The display backlight brightness can be adjusted using a series of keypresses. The keypad backlight can be either on or off. The 23 key keypad has a Power key, alphanumeric keys, function keys, cursor control keys, and Blue, Alpha, Enter, and Backspace keys. The HX2 hip flip holster, voice case, rubber boot, powered cradle, touchscreen stylus and protective film for the screen are available from LXE as accessories (see Accessories). Note: Until the tethered battery and backup battery are completely depleted, the HX2 is always drawing power from the batteries (On). Note: If the mobile device has AppLock installed, please refer to the HX2 Reference Guide for setup and processing information before continuing. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
2 Ring Scanner Warnings and Labels HX2 User’s Guide E-EQ-HX2OGWW-A Related Manuals This guide takes you through an introduction to and operation of the HX2. Ring Scanner Programming Guide – contains programming barcodes used when setting up ring barcode reader engines. HX2 Reference Guide – contains technical information and advanced instruction. HX2 Multi-Charger User’s Guide – contains user, technical and troubleshooting information for the HX2 battery multi-charger. HX2 Cradle Reference Guide – contains user, technical and troubleshooting information for the HX2 cradle. Ring Scanner Warnings and Labels • Do not look into the ring scanner/imager aperture. • Do not stare directly into the ring scanner/imager laser beam. • Do not remove the laser caution labels from the ring scanner/imager. • Do not connect the ring scanner aperture to any other device. Caution: Laser radiation when open. Please read the caution labels. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known tro be harmful. Figure 1 Ring Scanner Caution Label – Class 2 Laser Scanner For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Important Battery Information 3 E-EQ-HX2OGWW-A HX2 User’s Guide Important Battery Information Backup Battery -- If the HX2 has been without a power source (connected to a fully charged tethered battery or docked in a powered cradle) for an extended period of time or if HX2 external power sources become completely discharged or dead, a fully charged HX2 backup battery will last for up to 15 minutes. If the backup battery is fully discharged, the HX2 will reset as soon as it is docked in a powered cradle or connected to a fully charged tethered battery. A reset will cause loss of data and custom programs in RAM. Always store unused HX2s with a fully charged tethered battery. If possible, ensure the HX2 is periodically docked in a powered cradle to maintain an optimum backup battery charged status. To check battery status tap | Settings | Control Panel | Battery tab. • Until the tethered battery and backup battery are completely depleted, the HX2 is always drawing power from the batteries (On). • New Standard / Extended batteries must be fully charged prior to use. • Whenever possible, place the HX2 in a powered cradle to conserve tethered battery power and recharge the backup battery. • When a new battery is tethered to the HX2 for the first time (or after the backup battery has been fully depleted), the Time and Date reverts to factory default values. • Backup battery replacement is performed by LXE. The HX2 cradle can charge two standard batteries in less than four hours or two extended batteries in less than 8 hours in the battery wells behind the HX2 docking bay. The cradle requires an external power source before battery charging can commence. The HX2 Multi-Charger can charge up to six batteries at the same time. Each charging bay can accept either battery. The Multi-Charger requires an external power source before charging/analyzing can occur. Li-Ion Battery When disposing of the HX2 tethered batteries, the following precautions should be observed: The battery should be disposed of properly. The battery should not be disassembled or crushed. The battery should not be heated above 212°F (100°C) or incinerated. Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Attention II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type equivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
4 Environmental Specifications HX2 User’s Guide E-EQ-HX2OGWW-A Environmental Specifications HX2 Operating Temperature 14°F to 122°F (-10°C to 50°C) [non-condensing] Storage Temperature -4°F to 158°F (-20°C to 60°C) [non-condensing] Water and Dust IEC 60529 compliant to IP54 Operating Humidity 5% to 90% non-condensing at 104°F (40°C) Display Readability Indoor readable Wireless Compatibility WiFi, CCX, LXE-delivered/certified access points Bluetooth Range 32.8 feet (10 meters) Direct line of sight only. Lithium Ion Battery Pack Note: Battery packs can only be charged when their temperature is between 50°F (10°C) and 113°F (45°C). Operating Temperature -4°F to 120°F (-20°C to 50°C) [non-condensing] Storage Temperature -4°F to 160°F (-20°C to 70°C) [non-condensing] Water and Dust IEC 60529 compliant to IP54 Operating Humidity 5% to 90% non-condensing at 104°F (40°C) mAh Standard battery pack: 2000 mAh Extended battery pack: 4000 mAh Charge Time Standard battery pack: 4 hours Extended battery pack: 8 hours Discharge Time Standard battery pack: 8 hours Extended battery pack: 16 hours Dimensions Standard battery pack: 1.7” Width x 0.6” Height x 4.9” Length Extended battery pack: 1.7” Width x 1.0” Height x 4.9” Length For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Document Conventions 5 E-EQ-HX2OGWW-A HX2 User’s Guide Document Conventions ALL CAPS All caps are used to represent disk directories, file names, and application names. Menu | Choice Rather than use the phrase “choose the Save command from the File menu”, this guide uses the convention “choose File | Save”. Italic Titles Indicates the title of a book, chapter or a section within a chapter (for example, Document Conventions). < > Indicates a key on the keypad (for example, <Enter> ). Indicates a reference to other documentation. ATTENTION Keyword that indicates vital or pivotal information to follow. Attention symbol that indicates vital or pivotal information to follow. Also, when marked on product, means to refer to the user’s guide. International fuse replacement symbol. When marked on the product, the label includes fuse ratings in volts (v) and amperes (a) for the product. Note: Keyword that indicates immediately relevant information. Caution Keyword that indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Warning Keyword that indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Danger Keyword that indicates a imminent hazardous situation which, if not avoided, will result in death or serious injury. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
6 Getting Help HX2 User’s Guide E-EQ-HX2OGWW-A Getting Help All LXE user guides are now available on one CD and they can also be viewed/downloaded from the LXE ServicePass website. Contact your LXE representative to obtain the LXE Manuals CD. You can also get help from LXE by calling the telephone numbers listed on the LXE Manuals CD, in the file titled Contacting LXE. This information is also available on the LXE website. Explanations of terms and acronyms used in this guide are located in the file titled LXE Technical Glossary on the LXE Manuals CD and the LXE ServicePass website. Manuals • HX2 User’s Guide - English • HX2 User’s Guide – German • HX2 Cradle Reference Guide • HX2 Reference Guide • HX2 Multi-Charger / Analyzer User’s Guide • LXEbook – HX2 User’s Guide (download to mobile device) • RFTerm Reference Guide • LXE Security Primer • CE API Programmers Guide • Ring Scanner Programming Guide Accessories Note: Items with a Green letter R in the second column are ROHS-compliant. Please contact your LXE representative when ordering ROHS-compliant items as the part number may have changed. Items without the letter R may have received ROHS-compliance after this guide was published. E designator means the accessory is Exempt. Power HX2 Standard Battery, Lithium Ion E HX2A301BATTSTD HX2 Extended Battery, Lithium Ion E HX2A302BATTEXT 6 slot battery charger with universal power supply. Includes analyzing capabilities on one slot. US power cord included. R HX2A310CHRG6US 6 slot battery charger with universal power supply. Includes analyzing capabilities on one slot. Power cord not included. R HX2A311CHRG6WW Cradle HX2 Desk cradle with spare charging slot. Includes universal power supply. US power cord included. R HX2A312DESKCRADLEUS HX2 Desk cradle with spare charging slot. Includes universal power supply. Power cord not included. R HX2A313DESKCRADLEWW For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Getting Help 7 E-EQ-HX2OGWW-A HX2 User’s Guide Mobility Armband with standard wrist straps R HX2A201ARMBAND Replacement wrist straps (standard) for armband R HX2A202WRISTSTD Replacement wrist straps (extended) for armband R HX2A203WRISTEXT Hip Flip (for belt mounting) R HX2A221HIPFLIP Voice case (for belt mounting) R HX2A222VOICECASE Belt for hip flip or voice case R 9200L67 Barcode Readers SR laser for armband (short cable) R HX2A101SRSLASER SR laser for hip flip or voice case (long cable) R HX2A102LRSLASER RS-409 SR laser for armband (short cable) R HX2A120SRS409 2D Imager for armband (short cable) R HX2A110SRSIMAGER 2D imager for hip flip or voice case (long cable) R HX2A111LRSIMAGER Cables USB ActiveSync Cable (Type A to HX2 cradle connector) R HX2A001CBLACTVSYNC Battery Cable R HX2A002CBLBATT Battery Cable with Audio R HX2A003CBLBATTAUDIO Battery Extension Cable R HX2A004CBLBATTEXT Miscellaneous Rubber protective boot, gray R HX2A232BOOTGRAY Replacement Stylus , 10-pack R 9000A507STYLUS CD with CE 5.0 API’s and LXE API’s with documentation for custom application development R HX2A501CE50SDK Touchscreen anti-glare anti-reflective protective film, 10 pack R HX2A502PROTFILM For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
8 Getting Help HX2 User’s Guide E-EQ-HX2OGWW-A Audio Single ear, single headband, headset with noise canceling microphone, includes 5 replacement windscreens R HX1A501SNGBHEADSET Single ear, dual headband, headset with noise canceling microphone, includes 5 replacement windscreens R HX1A502DUALBHEADSET Dual ear, behind the head, headset with noise canceling microphone, includes 5 replacement windscreens R HX1A503BTHHEADSET Replacement foam block for 502 dual band headsets, qty 1 R HX1A504AHSBLOCKFOAM Replacement head yoke for dual band 502 headset, qty 1 R HX1A505DUALYOKE Replacement head yoke for single band 501 headset, qty 1 R HX1A506SINGLEYOKE Replacement windscreen for all headset microphones, 10 Pack R HX1A508WINDSCREEN10 Replacement windscreen for all headset microphones, 50 Pack R HX1A509WINDSCREEN50 Replacement foam ear piece cover for 501 and 502 headsets, 10 pack R HX1A510FOAMEAR10 Replacement foam ear piece cover for 501 and 502 headsets, 50 pack R HX1A511FOAMEAR50 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Components Note: The figures on the next few pages assume a fully charged tethered battery is in the battery sleeve (on an armband or hip flip) and positioned at the top of the figure. Please contact your System Administrator for assistance with HX2 accessories. Note: New batteries must be charged prior to use. The backup battery is continually recharged by the tethered battery. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
10 Front HX2 User’s Guide E-EQ-HX2OGWW-A Front Figure 2 Front 1 On / Off Button 2 System Status LED 3 Microphone 4 Bluetooth LED 5 Speaker 6 Alpha Mode LED 7 Enter Button For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Back 11 E-EQ-HX2OGWW-A HX2 User’s Guide Back Note: Before connecting cables to the back, make sure the battery sleeve on the armband is uppermost or the left arm / right arm directions won’t work. Figure 3 Back Left Arm Use 1 Ring Scanner Tether cable channel 2 Retaining Clip for Ring Scanner Tether Connector 3 Ring Scanner cable connector 4 Battery Cable connector 5 Retaining Clip for Tethered Battery Connector 6 Tethered Battery Cable channel 7 Cradle Connector Right Arm Use 1 Tethered Battery Cable channel 2 Retaining Clip for Tethered Battery Connector 3 Battery Cable connector 4 Ring Scanner cable connector 5 Retaining Clip for Ring Scanner Tether Connector 6 Ring Scanner Tether Cable channel 7 Cradle Connector For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
12 Connectors HX2 User’s Guide E-EQ-HX2OGWW-A Connectors Ring Scanner / Audio / Battery Connection Figure 4 Scanner / Audio / Battery Ports – Connector 1 and 2 Connector 1 Connector 2 • Tethered Ring Scanner (Laser or Imager) • Tethered Headset/Microphone and HX2 Battery • Tethered Battery See Cables. Cradle Connection Figure 5 Cradle/Power Port – Connector 3 (Base) Connector 3 is at the base of the HX2. It connects to the Cradle. When the HX2 is in a powered cradle, the HX2 receives external power through the Cradle connector. USB Keyboard or USB Mouse input is received through the Cradle connector when the HX2 is in a cradle. Connector 3 • Cradle • Cradle Power Input • USB Keyboard or mouse through cradle ports See the HX2 Cradle Reference Guide for instruction. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Tethered Ring Scanner / Imager 13 E-EQ-HX2OGWW-A HX2 User’s Guide Tethered Ring Scanner / Imager Figure 6 Laser Ring Scanner Figure 7 Imager Ring Scanner 1 Laser /Imager Scan Aperture 2 Scan-in-Progress LED 3 HX2 Connector 4 Scan button (Trigger) Figure 8 Concept - Ring Scanner Hook and Loop Strap Figure 9 Ring Scanner/Imager Apertures 1 Imager – Illumination LEDs 2 Beam Aperture 3 Imager – Clear Glass Lens 4 Laser Scanner – Red Glass Lens For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
14 Cables HX2 User’s Guide E-EQ-HX2OGWW-A Cables Figure 10 Cable – Battery and HX2 Connectors Figure 11 Cable – Audio, Battery and HX2 Connectors Figure 12 Cable – Laser Ring Scanner and HX2 Connectors Figure 13 Cable – Imager Ring Scanner and HX2 Connectors For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Li-Ion Battery 15 E-EQ-HX2OGWW-A HX2 User’s Guide Li-Ion Battery Main battery charging is handled exclusively by the HX2 Multi-Charger/analyzer and the battery charger integrated into a powered HX2 cradle. The Standard battery is much thinner than the Extended battery. Each battery will fit in the battery sleeve on an armband, hip flip and the voice case. Note: Do not allow water or chemical cleaning agents of any kind to come in contact with the battery charging contacts or the battery cable connector; they may be damaged. If necessary, clean them with a soft-bristle, dry brush or compressed air. Standard Battery Extended Battery Figure 14 HX2 Standard and HX2 Extended Battery Battery Charge/Connect Terminals HX2 Battery Cable Connector Note: When placing the tethered battery in an armband or hip flip battery sleeve, ensure the Battery Charge/Connect terminals are protected from accidental damage by keeping them covered by the sleeve fabric at all times. Note: New batteries must be charged prior to use. The backup battery is continually recharged by the tethered battery. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
16 Mounting Bracket Clips HX2 User’s Guide E-EQ-HX2OGWW-A Mounting Bracket Clips Mounting brackets are pre-installed to the back of the HX2. The brackets (one on each side) secure the HX2 to the mounting bracket clips on a hip flip or the armband. Figure 15 Mounting Brackets The HX2 mount assembly is pre-installed to a hip flip or armband. Figure 16 Armband and Hip Flip Mount Assembly and Clips Connect Center the HX2 over the mount assembly and gently push down until both bracket clips (indicated by the arrows shown above) snap over the brackets on the HX2. Carefully test the connection to make sure the HX2 is secured to the armband or hip flip. Reset the connection by pressing down on either mounting clip to release the HX2 and try again. Disconnect Remove the HX2 from the mount assembly by pushing down on either mounting clip, or both, until the HX2 mounting bracket disconnects. Or you can disconnect one side, then lift the HX2 up at a 45 degree angle until the other side disconnects. Lift the HX2 up and away from the mount assembly. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Mounting Devices 17 E-EQ-HX2OGWW-A HX2 User’s Guide Mounting Devices Armband Armband – Top View 1 HX2 Mounting Bracket 2 Bracket Clips 3 Battery Sleeve 4 Stylus Holder 5 Arm Strap Brackets Armband – Bottom View 1 Removable Mesh Arm Cover 2 Arm Strap Brackets 3 Adjustable Arm Straps Figure 17 Armband / Top and Bottom Straps Figure 18 Armband Straps 1 Hook Fabric 2 Loop Fabric 3 Connection tabs. Slide through Arm Strap Brackets and press hook and loop fabric together to secure strap to arm band. 4 Put this side of the strap on the inside, against the arm 5 Put this side of the strap on the outside For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
18 Mounting Devices HX2 User’s Guide E-EQ-HX2OGWW-A Hip Flip Figure 19 Hip Flip and Belt 1 HX2 Mounting Bracket on Hip Flip 2 Mounting Bracket Clips 3 A Belt inside the Belt Loop 4 Brace (Adjustable) For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Quick Start Getting Started Note: The sequence of steps in Getting Started/Pre-requisites must also be completed when the HX2 returns from a Cold Boot and when a new OS version is loaded. The wireless client, flash card, virtual keyboard and scanner parameters may also need to be reset after a cold reset. This section’s instructions are based on the assumption that your new device is pre-configured and requires only accessory installation (e.g. stylus, headset, ring scanner, etc.) and a battery. LXE recommends that installation or removal of accessories be performed on a clean, well-lit surface. When necessary, protect the work surface, the mobile device, and components from electrostatic discharge. Pre-requisites • A fully charged battery is available. • Optional add-on devices are available (e.g. stylus, headset, ring scanner, hip flip, voice case, armband). • Wireless Client configuration has been completed by the System Administrator. • Required configured (mappable) keys have been assigned by the System Administrator. For example, the default keypad configuration does not have a , Control, Shift, Alt or Del key (or the equivalent). Key mapping can be changed to map those specific keys if needed. • Optional software and LXE applications have been installed and setup by the System Administrator. HX2 Quick Start First Connect cabled devices to the HX2 See Connecting the Battery and Ring Scanner. See Connecting the Audio Cable and a Headset. Next Power up the HX2 and set up personal preferences See Tapping the Power Key. Locate the stylus. Calibrate the touchscreen, if necessary. See Tapping the Touchscreen with a Stylus and Calibrating the Touchscreen. A white screen will appear during the bootup process until all drivers and applications are loaded and installed. Setup screens may appear and disappear while files are loading. After all files are loaded and the Desktop is displayed, adjust audio volume and other parameters if desired. Then Setup wearable accessories See Wearable Device Assembly and Optional Equipment. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
20 Getting Started HX2 User’s Guide E-EQ-HX2OGWW-A HX2 Mobile Device - Quick Start Troubleshooting Can’t calibrate the touchscreen, change the date/time or adjust the volume. AppLock is installed and running on the mobile device. AppLock restricts User access to running programs. Changes or modifications require Administrator access. Refer to HX2 Reference Guide for setup and processing information. RFterm® opens and runs upon each cold reset and warm reset. Tap File | Exit to close the RFTerm application. By default RFTerm runs upon each cold reset and warm reset. HX2 seems to lockup as soon as it is warm booted. There may be slight delays while the wireless client connects to the network, authorization for voice-enabled applications complete, Wavelink Avalanche management of the HX2 startup completes, and Bluetooth relationships establish or re-establish. When the desktop appears or an application begins, the HX2 is ready for use. Wearable Device Assembly Armband Figure 20 HX2 Armband, Left Arm Orientation, Ring Scanner, Audio Prerequisite: Optional add-on devices are available. • Fasten the armband to your left or right arm before continuing with these directions. See Connecting the Battery and Ring Scanner. • Slide the battery into the battery sleeve on the armband. • Snap all tethered devices to the connectors at the back of the HX2. See Connecting the Battery and Ring Scanner and Connecting the Audio Cable and a Headset. • Snap the HX2 into the armband mounting bracket. See Mounting Bracket Clips. • Attach the battery cable to the battery. • Connect audio devices (see Connecting the Audio Cable and a Headset), if included. • Slip the ring scanner (if included) over one of your fingers, making sure your thumb or trigger finger can easily reach the Scan button. See Ring Scanner Strap. • Adjust the HX2 arm assembly for comfort. Occasionally check all connectors for stability. The wearable computer is ready for use. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Getting Started 21 E-EQ-HX2OGWW-A HX2 User’s Guide Hip Flip Prerequisite: Optional add-on devices are available. • Unpack the Hip Flip. Slide the belt through the loops on the Hip Flip. Do not put the hip flip on yet. • Slide the battery into the battery sleeve on the hip flip. • Snap all tethered devices to the connectors at the back of the HX2. See Connecting the Battery and Ring Scanner and Connecting the Audio Cable and a Headset. • Snap the HX2 into the hip flip mounting bracket. See Mounting Bracket Clips. • Attach the battery cable to the battery. • Put the hip flip on. • Slip the ring scanner (if included) over one of your fingers, making sure your thumb or trigger finger can easily reach the scan button. See Ring Scanner Strap. • Adjust the HX2 hip assembly for comfort. Occasionally check all connectors for stability. Figure 21 HX2 Hip Flip, Audio The wearable computer is ready for use. Ring Scanner Strap The ring scanner finger loop is located under the ring scanner. Pull gently on the end of the finger loop strap to separate the hook and loop fabric. Slide your finger into the opened loop under the ring scanner. Grasp the end of the finger loop strap and loosen then tighten the finger strap until the ring scanner is comfortably snug and the scan aperture is secured in the desired location. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
22 Connecting the Battery and Ring Scanner HX2 User’s Guide E-EQ-HX2OGWW-A Connecting the Battery and Ring Scanner Note: The unit will not function unless a battery is securely tethered. Be sure to place the mobile device in Suspend mode before disconnecting a battery, or all unsaved data may be lost. The battery and ring scanner cables should not be exchanged or replaced in a dirty, harsh or hazardous environment. When the tethers are disconnected, any dust or moisture that adheres to the tether connector can potentially cause damage upon cable connection. Follow the numbers in the following tables to connect the battery and ring scanner to the HX2. Note: Before connecting cables to the back, make sure the battery sleeve on the armband is uppermost or the following left/right directions won’t work. Figure 22 Tether the Battery and Ring Scanner – Left / Right When you want to switch connectors from left to right, or vice versa, first gently press downward on the Retaining Clip, then pinch and pull the cable connector (not the cable!) straight up and away from the HX2. Do not use a metal object, or extreme force, to remove the cable connector from the HX2. Re-connect cables and reassemble the HX2 body-worn components. Ring Scanner on the Left Hand 1 Ring Scanner Tether cable 2 Retaining Clip for Ring Scanner Tether Connector 3 Ring Scanner cable connector 4 Battery Cable connector 5 Retaining Clip for Tethered Battery Connector 6 Tethered Battery Cable Ring Scanner on the Right Hand 1 Tethered Battery Cable 2 Retaining Clip for Tethered Battery Connector 3 Battery Cable connector 4 Ring Scanner cable connector 5 Retaining Clip for Ring Scanner Tether Connector 6 Ring Scanner Tether Cable For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Connecting the Audio Cable and a Headset 23 E-EQ-HX2OGWW-A HX2 User’s Guide Connecting the Audio Cable and a Headset Note: The audio option draws power from the tethered battery.The mobile device internal speaker and internal microphone are disabled when a headset and microphone is connected. The headset consists of an earpiece, a microphone and an attached cable. The headset attaches to the audio cable which attaches to the HX2. Figure 23 Audio Cable and Headset 1 Align the audio connector and the headset quick connect cable end. Firmly push the cable ends together until they click and lock in place. 2 Snap the battery plug into the battery cable connector at the top of the battery. 3 Press the battery/audio connector into either left or right connector on the back of the HX2. The retaining clip will snap into place and secure the cable connection. Place the cable in the cable groove. See section titled Set the Audio Speaker Volume. Adjust Microphone and Secure the Cable Do not twist the microphone boom when adjusting the microphone. The microphone should be adjusted to be about two finger widths from your mouth. Make sure the microphone is pointed at your mouth. Note the small “Talk” label near the mouthpiece. Make sure the Talk label is in front of your mouth. The microphone cable can be routed over or under clothing. Under Clothing • Leave the cable exposed only at the top of the collar. • Be sure to leave a small loop of cable to allow movement of your head. Over Clothing • Use clothing clips to hold the cable close to your body. • Tuck the cable under the belt, but leave a small loop where it goes under the belt. • Do not wear the cable on the front of your body. It may get in your way or get caught on protruding objects. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
24 Tapping the Power Key HX2 User’s Guide E-EQ-HX2OGWW-A Tapping the Power Key The Power key is a round button located above the F4 key. When a battery is connected to the HX2 for the first time press the Power key. The mobile device begins the startup process. Wait until the Windows CE desktop appears. Suspend/Resume Mode -- At other times, tapping the Power key places the HX2 immediately in Suspend Mode. Tapping the Power key again immediately returns the HX2 from Suspend. Tapping the Touchscreen with a Stylus Note: Always use the point of the stylus for tapping or making strokes on the touchscreen. Never use an actual pen, pencil, or sharp/abrasive object to write on the touchscreen. Hold the stylus as if it were a pen or pencil. Touch an element on the screen with the tip of the stylus then remove the stylus from the screen. Firmly press the stylus into the stylus holder when the stylus is not in use. Similar to using a mouse to left-click icons on a desktop computer screen, using the stylus to tap icons on the touchscreen is the basic action that can: • Open applications • Choose menu commands • Select options in dialog boxes or drop-down boxes • Drag the slider in a scroll bar • Select text by dragging the stylus across the text Place the cursor in a text box prior to typing in data or retrieving data using the ring scanner or an input/output device connected to a serial port. A stylus can be ordered from LXE. See the section titled Accessories. Note: A “right mouse click” function must be programmed into the customer application to accept a constant stream of left mouse click messages. An application can choose to interpret this stream of messages as a right mouse click. LXE does not support non-LXE application programming. Calibrating the Touchscreen If the touchscreen is not responding properly to stylus taps, you may need to recalibrate the touchscreen. Recalibration involves tapping the center of a target. If you miss the center, keep the stylus on the screen, slide it over the target’s center, and then lift the stylus. To recalibrate the screen, select | Settings | Control Panel | Stylus | Calibration tab. To begin, tap the Recalibrate button on the screen with the stylus. Follow the instructions on the screen and press the Enter key to save the new calibration settings or press Esc to cancel or quit. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Power Key Functions 25 E-EQ-HX2OGWW-A HX2 User’s Guide Power Key Functions See Also: Sections titled LED Indicators and System Status LED later in this guide. • If installed, RFTerm runs automatically at the conclusion of each reboot. • If installed and enabled, AppLock runs automatically at the conclusion of each reboot. • The wireless client connects automatically during each reboot. • Bluetooth re-connects to paired devices automatically at the conclusion of each reboot. • If installed and pre-configured, Wavelink Avalanche connects remotely and downloads updates automatically during each reboot. Hardware Reset Press and hold the Power key for approximately 15 seconds until the display blanks, then release the key. If user data was not saved before the Hardware Reset function started, data loss occurs and unsaved registry settings are lost. User data is saved whenever a Suspend/Resume function is complete. Warm Boot Tap | Run and type warmboot. Tap the OK button. A warm boot does not affect the operating system, but programs and data in RAM are cleared, and registry changes, if any, are saved. Network and Bluetooth connections will need to be re-established. There may be slight delays while the wireless client connects to the network, re-authorization for voice-enabled applications completes, Wavelink Avalanche management of the HX2 startup completes, or Bluetooth relationships establish or re-establish. Cold Boot Tap | Run and type coldboot. Tap the OK button. Factory default settings overwrite all previously saved user settings. Calibrating the touchscreen will need to be performed when the cold boot process is complete. Wireless Client configuration will need to be completed by the System Administrator. Required mappable keys will need to be configured. For example, there is no , Control, Shift, Alt or Del key (or their equivalent) available using the HX2 default keypad setting. Optional software 1 and LXE application 2 parameters will need to be set up by the System Administrator. Important -- Because of the extreme nature of the Cold Boot, LXE recommends that the Cold Boot process be used only as an emergency procedure and Warm Boot or Suspend/Resume be used whenever necessary. Note: Refer to the section titled Power Modes in the HX2 Reference Guide for more information relating to the power states of the HX2. 1 Optional software setup may include Summit Wireless Client communication setup, Voice-Enabled software connection to wireless link, Wavelink Avalanche management of the HX2 file structure at startup, and Bluetooth device-pairing and re-connect. 2 LXE application software setup may include Summit Wireless Client communication setup, RFTerm terminal emulation configuration, and AppLock application-locking configuration. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
26 Using the 23 Key Keypad HX2 User’s Guide E-EQ-HX2OGWW-A Using the 23 Key Keypad Figure 24 The 23 Key Keypad • When using a sequence of keys that require an alphabet key, first press the Alpha key to force Alpha mode on the numeric keys. See Alpha Modifier Key in the HX2 Reference Guide. • Double tap the Alpha key for upper case alphabetic characters (similar to CapsLock. Single tap the Alpha key to exit CapsLock mode). • Single tap the Alpha key to enter and exit Alpha mode. • Default Alpha mode produces lower case alphabetic characters when numeric keys are pressed. • Pressing the Alpha key forces “Alpha” mode for all keys. • To create a combination of numbers and letters before pressing Enter, remember to tap the Alpha key to toggle between Alpha and Numeric mode. • Use the Input Panel to enter characters that are not available using the 23-key keypad. • When using a sequence of keys that do not include the Alpha key (Orange) but does include a sticky key (Blue), press the Blue key in sequence. Inserting Characters Using the Input Panel You can use the Input Panel to insert the following characters: < > { } [ ] ( ) _ + : ; “ ‘ ? / ~ ` ! @ # $ % ^ & | See Input Panel later in this guide. See Appendix A Key Maps for instruction on the specific keypresses to access all allowed keypad functions. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
System Status LEDS 27 E-EQ-HX2OGWW-A HX2 User’s Guide System Status LEDS Figure 25 System Status LEDs LED Color Indicates . . . Green - Blinking Display turned off when timer expired. This will help to conserve battery power. Tap the screen or press any key (except the Power button) to turn the display on again. The HX2 is not in Suspend Mode. Red - Steady Main Battery Low. If the main battery is not replaced with a fully charged battery before the main battery fails, the HX2 is turned Off. 1 System Status Red - Blinking Main Battery Power Fail Blue - Blinking Slowly Idle Blue - Blinking Fast Bluetooth is discovering Bluetooth devices 2 Bluetooth Off Bluetooth hardware has been turned off or does not exist in the HX2 3 Alpha Amber - Steady Alpha Mode enabled. When multiple system status conditions are present, the most urgent condition is indicated. The conditions listed above are in increasing order of urgency by LED type. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
28 Entering Data HX2 User’s Guide E-EQ-HX2OGWW-A Entering Data You can enter data into the HX2 through several different methods. The Ring Scanner aperture provides barcode data entry, the Input/Output (I/O) ports, the built-in microphone and speaker are used to input/output data, and the physical and virtual keypads provide text entry. Mobile devices with a touchscreen use a stylus to input data, devices connected to the I/O ports and/or the keypad. An input panel (virtual keyboard) is available for applications that expect keyed input. Keypad Entry The keypad is used to manually input data that is not collected otherwise. A subset of desktop PC full keyboard functions are provided. Other key functions can be obtained using the programmable key (Blue+Enter), configurable 0 and 1 keys, or by remapping one of the mappable keys. Please refer to Appendix A – Key Maps for instruction on the unique keypresses to access the available keyboard functions. Almost every key on the keypad has two or three different functions. The primary function or numeric character is printed on the key. The Alpha or Blue keys are pressed when you want to use a second key function. For example, when you press the Blue key (the sticky key), then press the key that has the desired second-function key, the second-function key is the “active” key. The specific sticky character is printed above the corresponding key in Blue. Stylus Data Entry Note: This section is directed to the HX2 daily user. The assumption is that the mobile device has been configured and the touch screen calibrated by the System Administrator prior to releasing the HX2 for daily use. The touch screen should be calibrated before initial use. The stylus performs the same function as the mouse that is used to point to and click elements on a desktop computer. The stylus is used in the same manner as a mouse – single tap or double tap to select menu options, drag the stylus across text to select, hold the stylus down to activate slider bars, etcetera. Hold the stylus as if it were a pen or pencil. Touch an element on the screen with the tip of the stylus then remove the stylus from the screen. The touchscreen responds to an actuation force (touch) of 4 oz. (or greater) of pressure. The stylus can be used in conjunction with the keyboard and scanner and an input/output device connected to a serial port. Touch the stylus to the field of the data entry form to receive the next data feed. The cursor begins to flash in the field. The unit is ready to accept data from either the physical keypad, virtual keyboard, or the ring scanner. Note: Always use the point of the stylus for tapping or making strokes on the display. Never use an actual pen, pencil or sharp/abrasive object to write on the touchscreen. Place the stylus in the stylus holder when not in use. There is a built in stylus holder on the hip flip and the armband. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Entering Data 29 E-EQ-HX2OGWW-A HX2 User’s Guide Ring Scanner Data Entry Read all cautions, warnings and labels before using the ring scanner. Do not look into the ring scanner/imager lens. Do not stare directly into any beam emitted from the scanner/imager lens. Laser Scanner To scan with the laser barcode scanner, point the ring scanner laser aperture towards a barcode and press the Scan button. You will see a red laser beam strike the barcode. Align the red beam so that the barcode is centered within the beam. The laser beam must cross the entire barcode. Move the ring scanner towards or away from the barcode so that the barcode takes up approximately two-thirds the width of the beam. There may be an audible response combined with the Scan function. Correct Scan Incorrect Scan Incorrect Scan Figure 26 Laser Scan Beam on Linear Barcode See section titled Scan Status LED. 2D Imager Figure 27 Imager Bracketed Crosshair Target on 2D Barcode To scan with the Imager Ring Scanner, point the scan aperture towards a 2D barcode and press the Scan button. You will see a bracketed crosshair strike the barcode. Align the brackets so that the center of the barcode is covered by the crosshair. Move the ring scanner towards or away from the barcode until a response is emitted by the HX2 (1 beep, 2 beeps, a WAV file, etc) or the bracketed crosshair times out and disappears. The Imager LED may illuminate when the Scan button is pressed. There are three options that can be set by the System Administrator using the Scanner control panel applet: Internal illumination, External illumination, or Both. If external illumination is chosen, there are three white LEDs located above the imager aperture that will illuminate for the duration of the scan then turn off. See the previous section titled Tethered Ring Scanner / Imager figure titled Ring Scanner/Imager Apertures. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
30 Entering Data HX2 User’s Guide E-EQ-HX2OGWW-A Scan Status LED Figure 28 Concept - Scan Status LED The Scan Status LED (oval shaped LED on the top of the ring scanner) turns red when the laser beam is on. Following a barcode scan and read the Scan Status LED turns green for two seconds and the HX2 may beep, indicating a successful scan. If the scan was unsuccessful, the Scan Status LED turns off and a different beep sequence is heard. The ring scanner engine and Scan Status LED automatically turn off after a successful or unsuccessful read. The ring scanner is ready to scan again after the Scan button is released, or after the Scan Status LED turns off following a successful scan. Voice Data Data is entered into the HX2 by speaking into the headset’s microphone (or the internal microphone located below the Up Arrow) when prompted. Please contact your System Administrator if assistance is needed with the voice software installed on your HX2. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Entering Data 31 E-EQ-HX2OGWW-A HX2 User’s Guide Input Panel / Virtual Keyboard The virtual keyboard or input panel is always available when needed e.g. text field input. Tap the Keyboard icon in the Taskbar to put the virtual keyboard on the display. Using the stylus: • Tap the Shift key to type one capital letter. • Tap the CAPS key to type all capital letters. • Tap the au key to access symbols. Figure 29 Input Panel / Virtual Keyboard Some applications do not automatically display the Input Panel. In this case, do the following to use the Input Panel: 1. Tap the Input Panel/Virtual Keyboard icon in the taskbar. 2. Select Keyboard from the menu. 3. Tap the data entry area on the display when you want to enter data using the Input Panel. When finished entering data, tap the Keyboard icon in the Taskbar. Select Hide Input Panel. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
32 Bluetooth Devices HX2 User’s Guide E-EQ-HX2OGWW-A Bluetooth Devices Assumption: The System Administrator has Discovered and Paired targeted Bluetooth devices for each HX2. The System Administrator has also enabled / disabled Bluetooth settings and assigned a Computer Friendly Name for each HX2. See the HX2 Reference Guide for information and instruction on the HX2, Bluetooth control panel applet and supported Bluetooth printers and scanners. The Bluetooth taskbar Icon state and Bluetooth LED states change as Bluetooth devices are discovered, pair, connect, and disconnect. The Bluetooth LED is located next to the Right Arrow key on the keypad. The Bluetooth LED blinks slowly when it is idle. Blinks quickly when the HX2 is discovering other Bluetooth devices. And blinks normally when it is connected. There may be audible or visual signals from paired devices as they re-connect with the HX2. Non-LXE Bluetooth devices may be discovered but are inaccessible as they are filtered out on the Bluetooth Devices panel and are not displayed (see HX2 Reference Guide for details). Taskbar Icon Legend Bluetooth module is connected to one or more of the targeted Bluetooth device(s). HX2 is not connected to any Bluetooth device. HX2 is ready to connect with any Bluetooth device. HX2 is out of range of all paired Bluetooth device(s). Connection is inactive. Blue - Blinking Slowly Idle. Blue - Blinking Fast Bluetooth discovering other Bluetooth devices. Bluetooth LED Off Bluetooth hardware has been turned off or does not exist in the HX2. Note: When an active paired device, not the HX2, enters Suspend Mode, is turned Off or leaves the HX2 Bluetooth scan range, the Bluetooth connection between the linked device and the HX2 is lost. There may be audible or visual signals as paired devices disconnect from the HX2. The Bluetooth remote device should be as close as possible, in direct line of sight, with the HX2 during the pairing process. See Accessories for supported Bluetooth printers and scanners. AppLock, if installed, does not stop the end-user from using Bluetooth application, nor does it stop authorized Bluetooth-enabled devices from pairing with the HX2 while AppLock is in control. See HX2 Reference Guide for more Bluetooth information. Checking Battery Status Important: Until the tethered battery and backup battery are completely depleted, the HX2 is always drawing power from the batteries (On). Tap the | Settings | Control Panel | Battery icon. Main battery level, backup battery level, status and other details are displayed. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Entering the Multi AppLock Activation Key 33 E-EQ-HX2OGWW-A HX2 User’s Guide Entering the Multi AppLock Activation Key Note: The mobile device must have the touch screen enabled. Tap the taskbar icon to place the AppLock popup menu on screen. Tap Keyboard if a hotkey sequence will require Input Panel access. Application Switching Activation Key If the mobile device uses LXE’s Multi AppLock to allow the user to switch between two applications, the Activation key sequence is assigned by the AppLock Administrator. The key sequence switches the focus between one application and another. User data is entered using the application running in the foreground only. Touch Figure 30 AppLock – How to Switch Applications Tap the taskbar icon to place the popup menu on screen. Tap one of the application icons in the popup menu. Tap Keyboard if a hotkey sequence will require Input Panel access. The selected application is brought to the foreground while the other application continues to run in the background. Stylus taps affect the application running in the foreground only. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
34 Setting the Power Schemes Timers HX2 User’s Guide E-EQ-HX2OGWW-A Setting the Power Schemes Timers Note: Refer to the section titled Power Modes in the HX2 Reference Guide for information relating to the power states of the mobile device. Select | Settings | Control Panel | Power | Schemes tab. Change the parameter values and tap OK to save the changes. Figure 31 Power Properties – Schemes Tab Battery Power Scheme Use this option when the mobile device will be running on battery power only. Switch state to User Idle: Default is After 3 seconds Switch state to System Idle: Default is After 15 seconds Switch state to Suspend: Default is After 5 minutes AC Power Scheme Use this option when the mobile device will be running on external power (e.g. docked in a powered cradle). Switch state to User Idle: Default is After 2 minute Switch state to System Idle: Default is After 2 minutes Switch state to Suspend: Default is After 5 minutes The mode timers are cumulative. The System Idle timer begins the countdown after the User Idle timer has expired and the Suspend timer begins the countdown after the System Idle timer has expired. When the User Idle timer is set to “Never”, the power scheme timers never place the device in User Idle, System Idle or Suspend modes (even when the device is idle). Because of the cumulative effect, and using the Battery Power Scheme Defaults listed above: • The backlight turns off after 3 seconds of no activity, • The display turns off after 18 seconds of no activity (15seconds + 3seconds), • And the device enters Suspend after 5 minutes and 18 seconds of no activity. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Setting The Audio Speaker Volume 35 E-EQ-HX2OGWW-A HX2 User’s Guide Setting The Audio Speaker Volume Note: An application may override the control of the speaker volume. Turning off sounds saves power and prolongs battery life. The internal speaker is located on the front of the device above the “2” key. The audio volume can be adjusted to a comfortable level for the listener. Operational “beeps” are emitted from the speaker. A Battery/Audio cable is available for headsets, see Accessories and Cables. Using the Keypad Note: Volume & Sounds (in Settings | Control Panel) must be enabled before the following default key sequences will adjust the volume. The volume is increased or decreased one step each time the volume key sequence is pressed. To adjust speaker volume use the Blue+Up Arrow and Blue+Down Arrow keys to adjust volume until the speaker volume is satisfactory. Using the Touchscreen Figure 32 Volume & Sounds Properties Tap | Settings | Control Panel | Volume & Sounds | Volume tab. Change the volume setting and tap OK to save the change. You can also select / deselect sounds for key clicks and screen taps and whether each is loud or soft. As the volume scrollbar is moved between Loud and Soft, the computer will emit a tone each time the volume increases or decreases in decibel range. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
36 Adjusting the Display Backlight Timer HX2 User’s Guide E-EQ-HX2OGWW-A Adjusting the Display Backlight Timer Select | Settings | Control Panel | Display | Backlight tab. Change the parameter values and tap OK to save the changes. Figure 33 Setting the Display Backlight Timer The first option affects the display when the HX2 is running on battery power only. The second option affects the display when the HX2 is running on external power (e.g. docked in a powered cradle). The default value for the battery power timer is 3 seconds. The default value for the external power timer is 2 minutes. The display backlight will remain on all the time when both checkboxes are blank. The display backlight timer dims the backlight at the end of the specified time. When the Keypad Backlight is On, it responds to the settings of the Display Backlight Timer. See next segment titled Turning the Keypad Backlight On or Off. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Turning the Keypad Backlight On or Off 37 E-EQ-HX2OGWW-A HX2 User’s Guide Turning the Keypad Backlight On or Off Select | Settings | Control Panel | Display | Keypad | Alpha tab. Figure 34 Turning the Keypad Backlight On or Off Tap the Off radio button when the keypad backlight is to remain Off regardless of the OS event in process. The default is On. When On the keypad backlight responds to OS events as designed. When On, the keypad backlight responds to the settings of the Display Backlight Timer. See previous segment titled Adjusting the Display Backlight Timer. Cleaning the Glass Display/Ring Scanner Aperture Note: These instructions are for components made of glass. If there is a removable protective film sheet on the display screen, remove the film sheet before cleaning the screen. Keep fingers and rough or sharp objects away from the ring scanner aperture and the mobile device display. If the glass becomes soiled or smudged, clean only with a standard household cleaner such as Windex® without vinegar or use Isopropyl Alcohol. Do not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the glass surface. Use a clean, damp, lint-free cloth. Do not scrub optical surfaces. If possible, clean only those areas which are soiled. Lint/particulates can be removed with clean, filtered canned air. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
38 Cleaning the Glass Display/Ring Scanner Aperture HX2 User’s Guide E-EQ-HX2OGWW-A For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Optional Equipment HX2 Rubber Boot Assembly The rubber boot is a lightweight, flexible covering for the HX2 housing. The rubber boot cannot protect the HX2 from destructive, excessive force. It is designed to protect the HX2 housing from minor, trivial bumps or jostling. The rubber boot does not inhibit tethered devices, cradle docking, Hip Flip assembly or Armband assembly. Note: Remove the rubber boot when placing the HX2 in a voice case. The rubber boot slips over the front and halfway down the sides of the HX2, leaving the touch screen, keypad, LXE logo and the HX2 logo visible. Figure 35 HX2 Rubber Boot Gently stretch the rubber boot over each corner of the front housing until the rubber boot fits snugly. It can be removed for cleaning, if necessary. Smaller openings are available in the rubber boot to • allow access to the cradle connector on the bottom of the HX2 • allow audible signals from the internal speaker to be heard • and allow audible signals to be sent through the internal microphone. Protective Film for the Screen Display First, clean the display of fingerprints, lint particles, dust and smudges. Remove the protective film from its container. Remove any protective backing from the film sheet by lifting the backing from a corner of the film. Discard the backing. Apply the film to the screen starting at one side and smoothing it across the display. If air bubbles appear, raise the film slightly and continue smoothing the film across the display until it covers the glass surface of the display. If dust, lint or smudges are trapped between the protective film and the glass display, remove the protective film, clean the display and apply the protective film again. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
40 HX2 Voice Case Assembly HX2 User’s Guide E-EQ-HX2OGWW-A HX2 Voice Case Assembly The voice case is a sturdy, lightweight covering for the HX2, tethered battery, and voice accessories. The voice case cannot protect the HX2 from destructive, excessive force or a harsh or wet environment. It is designed to protect the HX2 from dirt, dampness, and minor, trivial bumps or jostling. Figure 36 HX2 Voice Case 1. Slide the belt through the belt loop on the voice case. Do not put the belt on yet. 2. Attach the battery cable, ring scanner and audio device to the HX2. 3. Slip the HX2 into the voice case. Be sure the screen and keypad are visible through the clear window of the voice case. 4. Slide the battery cable through the protective loop at the bottom of the voice case. Make sure the tethered cable for the ring accessory is on the outside of the voice case. 5. Slip the battery into the battery sleeve and connect the battery to the battery cable. The battery charge terminals (small metallic circles) should always be covered by the sleeve. 6. Press the hook and loop fabric at the top of the device together. 7. The HX2 in the Voice Case is ready for use. 8. Put the belt on. Adjust the belt and voice case for comfort. Examine the tethers and the hook and loop fabric fastening periodically. If any are loose or unfastened, tighten the tethers and the top fastener before placing the voice case back into service. If the voice case is damaged, it should be removed from service. Note: The HX2 with a voice case does not fit in the HX2 cradle. Remove the voice case before placing the HX2 in a charged cradle. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Removing/Replacing the Armband Straps 41 E-EQ-HX2OGWW-A HX2 User’s Guide Removing/Replacing the Armband Straps Note: Remove the HX2 and any of its tethered devices from the Armband before removing and replacing the armband straps. The armband is a lightweight, sturdy mounting platform for the HX2. There are two armband straps. The shorter strap is used at the end-user wrist area and the longer strap is used at the end-user forearm area. See Accessories for replacement or different lengths of LXE HX2 armband straps. Armband – Bottom View 1 Removable Mesh Arm Cover 2 Arm Strap Brackets 3 Adjustable Arm Straps Figure 37 Removing/Replacing the Armband Straps Figure 38 Armband Straps 1 Hook Fabric 2 Loop Fabric 3 Connection tabs. 4 Strap side for inside. 5 Strap side for outside. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
42 Removing/Replacing the Armband Straps HX2 User’s Guide E-EQ-HX2OGWW-A 1. Slip each end of the arm strap through the arm strap brackets ensuring the hook and loop fastening sections are on the outside of the armband. 2. Press the hook end against the loop fastener, located just below the loop fastener, to secure each end of the strap to the armband. After both straps are loosely fastened in this manner, snap the HX2 onto the armband bracket. 3. Slip your hand through the armband straps until the armband is in the desired location. Grasp the tab at one end of the strap to loosen and then tighten each strap until the armband is comfortably snug. 4. Ensure the HX2 on the armband is stable and does not slide or slip around your arm. 5. Periodically check the straps, strap brackets and hook and loop fabric areas for damage. The damaged parts should be replaced before the straps or strap brackets are used on an armband again. Note: The armband is washable, but only the mesh arm cover and straps are machine washable. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
HX2 Docking/Charging Cradle 43 E-EQ-HX2OGWW-A HX2 User’s Guide HX2 Docking/Charging Cradle Figure 39 Concept – An HX2, Two Batteries and 1 Ring Scanner in Cradle The HX2 USB desktop cradle secures the HX2 with or without a rubber boot, recharges the tethered HX2 battery and a spare battery (Standard and Extended), has a protected storage bay for the tethered Ring Scanner when the HX2 is docked, and enables serial communication with USB devices (host, client, and other USB cabled devices). HX2 keypad data entries can be mixed with ring scanner barcode data entries while the HX2 is docked in a cradle. Using an external power supply the HX2 cradle recharges Standard batteries in approximately 4 hours (8 hours for the Extended battery). The HX2 does not need to be docked during a spare battery charging process. See Accessories. Remove the voice case before placing the HX2 in the cradle. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
44 HX2 Docking/Charging Cradle HX2 User’s Guide E-EQ-HX2OGWW-A Cradle LEDs Figure 40 Concept - Powered Cradle LEDs 1 LED - Left battery charging bay Normal State – Off. With battery and power, normal state may be any state listed in Cradle LEDs. 2 LED - HX2 Docked / Receiving Power bay Normal State – Off. With HX2 and power, normal state is On. 3 LED - Right battery charging bay Normal State – Off. With battery and power, normal state may be any state listed in Cradle LEDs. HX2 Docked/Receiving Power LED When LED is … It means …. Off No AC/DC power supplied to the cradle and/or No HX2 or HX2 is not properly seated in charging bay. Green HX2 properly seated in charging bay and is receiving power through the cradle. Left and Right Battery Charging LED When LED is … It means …. Off No battery or no AC power No spare battery in the battery bay(s) or no AC/DC power is being applied to the cradle. Green Charged Spare battery pack fully charged. Red Charging Spare battery pack charging. Amber Standby Spare battery pack temperature out of range. Flashing Red Fault Spare battery pack fault or failure. Refer to the HX2 Cradle Reference Guide for instruction in setting up the cradle, inserting the battery packs, interpreting the LEDs, connecting cables and using the cradle for powering the HX2 and communication. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
HX2 Multi-Charger 45 E-EQ-HX2OGWW-A HX2 User’s Guide HX2 Multi-Charger The LXE HX2 Multi-Charger is designed to simultaneously charge up to six HX2 Rechargeable Lithium Ion Batteries at a time, in any combination of Standard or Extended batteries. The Standard batteries require less than four hours and the Extended batteries require less than 8 hours. Total charging time required depends upon battery pack temperature and conditions. There is one bay that is used for Charging only when the Analyze button is not pressed. Figure 41 HX2 Multi-Charger Charging Pocket LED LED Indication Description Off No Battery/power Battery pack not plugged in or no power applied. Green Charged Battery pack fully charged. Red Charging Battery pack charging. Yellow Standby Battery pack temperature out of range. Flashing Red on any station Fault Battery pack fault or failure. Flashing Red on any station Timeout Battery analyzer’s 4.5 hour timeout period expired. Flashing Red on all stations. Charger/Analyzer Failure Battery analyzer fault or failure. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
46 HX2 Multi-Charger HX2 User’s Guide E-EQ-HX2OGWW-A Charger/Analyzer LEDs Percentage of Battery Capacity Between 90% and 100% Between 80% and 90 % Between 70% and 80% Between 50% and 70% On Off Off Off On On Off Off On On On Off On On On On Analyze Progress LED Status When all LEDs are off, the battery capacity is less than 50%. Figure 42 Multi-Charger Control Panel Refer to the HX2 Multi-Charger User’s Guide for instruction in setting up the charger, inserting the battery packs into the charging bays, interpreting the LEDs and using the Charge/Analyze Pocket. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Appendix A Key Maps 23 Key Keypad Hints • When using a sequence of keys that require an alpha key, first press the Alpha key. • Double tap the Alpha key for upper case alphabetic characters. • Single tap the Alpha key to enter and exit Alpha mode. • Default Alpha mode produces lower case alphabetic characters when numeric keys are pressed. • Pressing the Alpha key forces “Alpha” mode for all keys. • To create a combination of numbers and letters before pressing Enter, remember to tap the Alpha key to toggle between Alpha and Numeric mode. • Use the Input Panel to enter characters that are not available using the 23-key keypad. • When using a sequence of keys that do not include the Alpha key (Orange) but does include a sticky key (Blue), press the Blue key first then the rest of the key sequence. First Press This Key To Get This Key / Function Blue Alpha Then Press This Key Power / Suspend Power Volume Up Blue Up Arrow Volume Down Blue Down Arrow Blue Mode (Toggle) Blue Alpha Mode (Toggle) Alpha Diamond Key Blue Enter (Start Button) Only Available when Mapped 3 Uppercase Alpha (Toggle) 4 Alpha Doubleclick Alpha key 4 Lowercase Alpha 4 N/A (default) Space Alpha 0 Enter Enter CapsLock Mode 4 Alpha times 2 Alpha Back Space Backspace Escape Blue Backspace Tab Blue Right Arrow BackTab Blue Left Arrow Up Arrow (Cursor Up) Up Arrow 3 Please contact your System Administrator for assistance with User Configured (Mapped) Keys. 4 See Using the 23 Key Keypad for explanation. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
48 23 Key Keypad HX2 User’s Guide E-EQ-HX2OGWW-A First Press This Key To Get This Key / Function Blue Alpha Then Press This Key Down Arrow (Cursor Down) Down Arrow Right Arrow (Cursor Right) Right Arrow Left Arrow (Cursor Left) Left Arrow F1 F1 F2 F2 F3 F3 F4 F4 F5 Blue F1 F6 Blue F2 F7 Blue F3 F8 Blue F4 F9 Only Available when Mapped 3 F10 Blue 0 F11 Blue 1 F12 Blue 2 F13 Blue 3 F14 Blue 4 F15 Blue 5 F16 Blue 6 F17 Blue 7 F18 Blue 8 F19 Blue 9 F20 Only Available When Mapped 3 a Alpha 2 b Alpha 22 c Alpha 222 d Alpha 3 e Alpha 33 f Alpha 333 g Alpha 4 h Alpha 44 i Alpha 444 j Alpha 5 k Alpha 55 l Alpha 555 m Alpha 6 n Alpha 66 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
23 Key Keypad 49 E-EQ-HX2OGWW-A HX2 User’s Guide First Press This Key To Get This Key / Function Blue Alpha Then Press This Key o Alpha 666 p Alpha 7 q Alpha 77 r Alpha 777 s Alpha 7777 t Alpha 8 u Alpha 88 v Alpha 888 w Alpha 9 x Alpha 99 y Alpha 999 z Alpha 9999 A Alpha times 2 2 B Alpha times 2 22 C Alpha times 2 222 D Alpha times 2 3 E Alpha times 2 33 F Alpha times 2 333 G Alpha times 2 4 H Alpha times 2 44 I Alpha times 2 444 J Alpha times 2 5 K Alpha times 2 55 L Alpha times 2 555 M Alpha times 2 6 N Alpha times 2 66 O Alpha times 2 666 P Alpha times 2 7 Q Alpha times 2 77 R Alpha times 2 777 S Alpha times 2 7777 T Alpha times 2 8 U Alpha times 2 88 V Alpha times 2 888 W Alpha times 2 9 X Alpha times 2 99 Y Alpha times 2 999 Z Alpha times 2 9999 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
50 23 Key Keypad HX2 User’s Guide E-EQ-HX2OGWW-A First Press This Key To Get This Key / Function Blue Alpha Then Press This Key 1 1 and 11111 (Alpha Mode) 2 2 and 2222 (Alpha Mode) 3 3 and 3333 (Alpha Mode) 4 4 and 4444 (Alpha Mode) 5 5 and 5555 (Alpha Mode) 6 6 and 6666 (Alpha Mode) 7 7 and 77777 (Alpha Mode) 8 8 and 8888 (Alpha Mode) 9 9 and 99999 (Alpha Mode) 0 0 and 00 (Alpha Mode) . (period) Alpha 1 \ Alpha 11 * (asterisk) Alpha 111 - (dash or minus sign) Alpha 1111 < > Use Input Panel [ ] Use Input Panel { } Use Input Panel ( ) Use Input Panel _ (underscore) Use Input Panel + (plus sign) Use Input Panel : ; Use Input Panel “ ‘ Use Input Panel ? / Use Input Panel ` ` Use Input Panel ! Use Input Panel @ Use Input Panel # Use Input Panel $ Use Input Panel % Use Input Panel ^ Use Input Panel & Use Input Panel | Use Input Panel For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Appendix B Regulatory Notices and Safety Information FCC Information: This device complies with FCC Rules, part 15. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this device not expressly approved by LXE, Inc., could void the user’s authority to operate this equipment. Industry Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada. Le present appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques de le Classe B préscrites dans le Reglement sur le brouillage radioélectrique édits par le ministere des Communications du Canada. Notice: The long term characteristics or the possible physiological effects of radio frequency electromagnetic fields have not been investigated by UL. Li-Ion Battery When disposing of the HX2 main battery, the following precautions should be observed: The battery should be disposed of promptly. The battery should not be disassembled or crushed. The battery should not be heated above 212°F (100°C) or incinerated. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
52 Index HX2 User’s Guide E-EQ-HX2OGWW-A R&TTE Directive Requirements (Applies only to equipment operated within the EU/EFTA) Information to User A label on the exterior of the device should resemble one of the labels shown below (the label contains the LXE part number of the installed radio card). The labels shown below and affixed to the device, identify where the device may be used and where its use is restricted. Use of a device is prohibited in countries not listed below or otherwise identified by the label. (May or may not include the 0560 Notifed Body No. Substitute 4 digit Notified Body No. may also be applied.) Permitted for use in: Austria, Belgium, Denmark, Finland, Germany, Greece, Hungary, Iceland, Italy, Ireland, Liechtenstein, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom Permitted for use in France. WEEE Statement Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about proper disposal, contact LXE through your local sales representative, or visit www lxe com. HX2 Approvals/Standards Product EMI / EMC Standards Safety Standards HX2 FCC Part 15 Subpart B, Class B EN 55022 Class B (CISPR 22) EN 55024:1998 AS/NZS 3548, Class B (CISPR 22) UL 60950-1 / CSA C22.2 No. 60950-1 IEC/EN 60950-1 Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. • EN60825-1:1994+ A1:2002 +A2:2001 • IEC60825-1:1993+A1:1997+A2:2001 Transceiver: Transceiver RF (2.4 GHz) standards RF Safety Standards HX2 with 802.11b/g [Summit Client] FCC Part 15.247, Subpart C FCC Bulletin OET-65 EN 300 328 IC-RSS 210 IC-RSS 102 Unlicensed Operation Unlicensed Operation Requires License for Outdoor Use This device contains transmitter Module FCC ID: KDZLXE4830P RF Safety Notice (Summit Client) Caution This portable device with its antenna complies with FCC’s and Industry Canada’s RF exposure limits set for an uncontrolled environment. This equipment has shown compliance with FCC and Industry Canada Specific Absorption Rate (SAR) limits. Highest reported SAR for the HX2 is .641W/kg on body. Any accessories not provided by LXE should not be used with this device. This device must not be co-located or operating in conjunction with any other antenna or transmitter. For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Index 53 E-EQ-HX2OGWW-A HX2 User’s Guide LXE 802.11b/g WLAN Declaration of Conformity (Summit Client) DECLARATION OF CONFORMITY according to Directives: 1999/5/EC 93/68/EEC Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity CE Marking Directive Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: Year of Manufacturer: Direct Sequence 2.4 GHz Wireless LAN Card LXE LXE 4830 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA 2006 The following harmonized European Standards, technical specifications, or other normative documents have been applied: EMC: EN 301 489-1: 07-2000 EN 301-489-17 07-2000 Radio: EN 300 328-1 and -2: 2000-7 Safety: EN 60950-2: 1992 + A1..A4 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Wideband data and HIPERLAN equipment Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques Safety of information technology equipment, including electrical business equipment We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety Requirements of the above Directives and Standards, as amended. Place: LXE Inc., Norcross GA USA C. Binnom Jr. RF Approvals Engineer Date of issue: 26 March 2007 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 fax 770/447-6928 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
54 Index HX2 User’s Guide E-EQ-HX2OGWW-A Annex to DoC for LXE 4830 With regard to the use of external antennas The LXE 4830 can be equipped with external antennas. The antennas listed have been evaluated with the LXE 4830 pursuant to EN 300 328, and therefore meet the definition of ‘dedicated antenna’ per ERC/REC 70-03 Appendix 1 Table 3; thus the requirement set forth in ERC/REC 70-03 , Annex 3 are met by the LXE model 4830 transceiver. Dedicated Antennas for use with LXE 4830 LXE P/N Antenna Gain Radio Power Level Antenna Description 153180-0001 2.2 dBi 15.8 dBm Omni, for LXE VX-series computers 160952-0001 0 dBi 15.8 dBm Omni, for LXE MX3-series computers 158399-0001 0 dBi 15.8 dBm Omni, for LXE MX5-series computers 159900-0001 0 dBi 15.8 dBm Omni, for LXE MX7-series computers 160019-0001 0 dBi 15.8 dBm Omni, for LXE VX-series computers 160501-0001 0 dBi 15.8 dBm Omni, for LXE HX1-series computers 160260-0001 0 dBi 15.8 dBm Omni, for LXE HX2-series computers C. Binnom Jr. RF Approvals Engineer 26 March 2007 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 fax 770/447-6928 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
Index 55 E-EQ-HX2OGWW-A HX2 User’s Guide Laser Light Safety Statement Warning: This product uses laser light. One of the following labels is provided on the scanner. Please read the Caution statement. (US) Mise én garde: Ce produit utilise un rayon laser. L’une des étiquettes suivantes est apposée sur le scanneur. Veuillez lire l’avertissement qu’elle contient. (FR) Advertência: Este produto usa luz de laser. O scanner contém um dos seguintes avisos. Favor ler o Aviso. (PT) Varning: Denna produkt använder laserljus. En av de nedanstående etiketterna sitter på scannern. Var god läs varningstexten. (SE) Advarsel: Dette produkt anvender laserlys. En af følgende mærkater anvendes på scanneren. Læs venligst sikkerhedsforanstaltningen. (DK) Varoitus: Tämä tuote käyttää laservaloa. Skannerissa on jokin seuraavista tarroista. Lue Huomio-kohta. (FI) Warnung: Dieses Produkt verwendet Laserlicht. Eines der folgenden Etiketten befindet sich auf dem Scanner. Bitte lesen Sie den Gefahrenhinweis. (DE) Attenzione: Questo prodotto utilizza luce laser. Una delle etichette seguenti c’ ubicata sullo scanner. Si raccomanda di leggere con attenzione le avvertenze riportate. (IT) Advarsel: Dette utstyret bruker laserlys. En av følgende etiketter er plassert på scanneren. Les advarselen på etiketten. (NO) Advertencia: Este producto usa luz de láser. Las etiquetas se proveen en la máquina exploradora. Por favor, lea detenidamente la explicación para las precauciones. (ES) Waarschuwing: Dit product gebruikt laserlicht. Een van de volgende labels is op de scanner aangebracht. Lees a.u.b. de waarschuwing onder Oppassen. (NL) Aþaðýdaki etiketlerden bir tanesitarayýcýnýn üstünde saðlanýr. Lütfen Dikkat ifadesini okuyun. (TR) (GR) (KR) (JP) (CN) Legend: Chinese-CN; Danish-DK; Dutch-NL; English-US; Finnish-FI; French-FR; German-DE; Greek-GR; Italian-IT; Japanese-JP; Korean-KR; Norwegian-NO; Portuguese-PT; Spanish-ES; Swedish-SE; Turkish-TR For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
56 Index HX2 User’s Guide E-EQ-HX2OGWW-A Laser Light Class 2 Labels – Ring Scanners Waiting for JPG file of labels Laser Light Class 2 Labels – Bluetooth Scanners Waiting for JPG file of labels For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
E-EQ-HX2OGWW-A HX2 User’s Guide Index 23 key keypad hints .................................................30 2D Imager................................................................29 A AC Power Scheme...................................................34 Accessories................................................................6 Electrostatic Discharge .......................................19 Activation Key.........................................................33 Alpha Mode LED ....................................................27 AppLock..................................................................33 Armband..................................................................17 Armband assembly ............................................20, 41 Assembly armband ..............................................................41 Armband .............................................................20 Audio Cable, Headset and Battery......................23 Battery and Ring Scanner ...................................22 Cables..................................................................22 protective film.....................................................39 rubber boot..........................................................39 voice case............................................................40 Audio Cable, Headset and Battery assembly...........23 Audio Volume settings ............................................35 B Backlight timer ..................................................36, 37 Barcode reader aperture...........................................13 Battery Check status ........................................................32 Important...............................................................3 Battery and Ring Scanner ........................................22 Battery Power Scheme.............................................34 Bluetooth Status LED..............................................27 Bracket Clips ...........................................................16 C Charge and connect contacts ...................................15 Cleaning...................................................................37 Coldboot ..................................................................25 Color displays and backlight timers.........................36 Components...............................................................9 Armband .............................................................17 Back ....................................................................11 Cables..................................................................14 Connectors ..........................................................12 Cradle connector .................................................12 Front....................................................................10 Hip Flip ...............................................................18 Mounting brackets...............................................16 Ring Scanners .....................................................13 Tethered battery ..................................................15 Contact LXE..............................................................6 Cradle Features...............................................................43 LEDs ...................................................................44 D Data entry imager .................................................................29 keypad.................................................................28 laser scanner........................................................29 stylus ...................................................................28 virtual keyboard ..................................................31 Data entry ................................................................28 Data Loss Backup Battery......................................................3 Display and scanner aperture cleaning ....................37 Display backlight timer .....................................36, 37 E Entering Data...........................................................28 F Features .....................................................................1 Forms entry..............................................................28 G Getting Started.........................................................19 Glossary.....................................................................6 H Hardware Reset .......................................................25 Help ...........................................................................6 Hints Key Maps............................................................47 Hip Flip....................................................................18 I Important Battery Information...................................3 Input panel For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals
58 Index HX2 User’s Guide E-EQ-HX2OGWW-A virtual keyboard ..................................................31 K Key Maps.................................................................47 Keypad and entering data ........................................28 Keypad and Input Panel keys ..................................26 L LEDs Cradle..................................................................44 HX2.....................................................................27 Multi-Charger .....................................................45 Li-ion battery...........................................................15 Lithium Ion battery warning......................................3 LXE applications .....................................................25 LXE Manuals CD ......................................................6 M Microphone on headset............................................23 Mode timers, Power.................................................34 Mounting brackets ...................................................16 Multi-Charger Features...............................................................45 Multifunction cables................................................14 O Operating Temperature Battery...................................................................4 HX2.......................................................................4 Optional software ....................................................25 P Power key ................................................................24 Power Scheme .........................................................34 Protective film .........................................................39 Q Quick Start Prerequisites........................................................19 Quick Start Instructions ...........................................19 R Recalibrate...............................................................24 Regulatory Notices ..................................................51 Related Manuals ........................................................2 Resume Mode, How To...........................................24 Risk of explosion Battery...................................................................3 RoHS Accessories .....................................................6 Rubber boot assembly .............................................39 S Safety Information...................................................51 Scanner status, LED ................................................30 Scanning and data entry...........................................29 Scheme ....................................................................34 Soft case..............................................See Voice Case Sound Scheme .........................................................35 Stylus and data entry................................................28 Stylus, Using............................................................24 Suspend Mode, How To ..........................................24 Suspend Timer.........................................................34 Switching applications AppLock .............................................................33 System Idle Timer ...................................................34 System Status LED..................................................27 T Timer User, System, Suspend........................................34 Touchscreen and data entry .....................................28 Touchscreen calibration...........................................24 Transcribing and data entry .....................................28 Troubleshooting, Quick Start...................................20 U User Idle Timer........................................................34 V Virtual keyboard Input panel ..........................................................31 Voice case assembly................................................40 Voice data and data entry ........................................30 Volume adjust audio volume ............................................35 W Warmboot................................................................25 Warnings and Labels Ring Scanner.........................................................2 For Approvals Review - Do not publish or distribute - LXE Confidential - Draft 09 / Approvals

Navigation menu