Juniper Networks 100 2.4GHz/5GHz Mini-PCI Module For Access Point User Manual Trapeze Manual s and reference

Juniper Networks, Inc. 2.4GHz/5GHz Mini-PCI Module For Access Point Trapeze Manual s and reference

UserManual.wiki >

Juniper Networks >

100 User Manual >

Contents

User Manual

Part Number: 730-9502-0001, Rev.1Trapeze Mobility Point™Installation GuideRelease: 1.0 Alpha

Customer Service iiiCustomer ServiceFor information and documentation about Trapeze Networks Mobility System products, go to www.trapezenetworks.com. For technical support, call or send email to the Trapeze Networks Technical Assistance Center (TAC).Contacting the Technical Assistance CenterTo contact the Trapeze Networks Technical Assistance Center (TAC): zCall 1-866-TRPZTAC (1-866-877-9822) from any location in the United States.zCall +1 925-474-2400 from locations outside the United States.zSend email to support@trapezenetworks.com. Be sure to have information about your product and the problem available when you call or write.In a Network EmergencyIf your Trapeze Networks Mobility System network fails, call either support telephone number 24 hours a day, 7 days a week.For All Other ProblemsFor problems other than network emergencies, call either support telephone number during regular business hours—between 8 a.m. and 6 p.m. Pacific Time (GMT–8). Or send email to support@trapezenetworks.com. You can expect a response within the next business day.Information TAC Needs about Your ProductHave the following information available when you call or write to TAC for technical assistance:zProduct name, model, and serial numberzSoftware version and release numberzAny software or hardware options you purchasedzType of computer you are usingzDescription of the problem and any relevant data

Information TAC Needs about Your ProductTrapeze Mobility Point Installation Guideiv

Contents vContentsChapter 1 Introducing the Trapeze Networks Mobility System . . . . 1Trapeze Networks Mobility System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Safety and Advisory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Text and Syntax Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Chapter 2 MP Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Mobility Point Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5External Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Cable Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Single Connection to an MX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Dual-Homed Connection to an MX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Dual-Homed Connection to Two MX Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Chapter 3 Installing an MP . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Unpacking an MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Installation Requirements and Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14MX Switch Recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Radio Safety Advisories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Installation Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Installing an MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Suspended Ceiling Installation—Flush Ceiling Tiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Suspended Ceiling Installation—Drop Ceiling Tiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Junction Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Solid Wall or Ceiling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Verifying MP Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Appendix A MP Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 33Appendix B MP Technical Specifications . . . . . . . . . . . . . . . . . . 35

vi Trapeze Mobility Point Installation Guide

Chapter 1: Introducing the Trapeze Networks Mobility System 1Chapter 1Introducing the Trapeze NetworksMobility SystemThis guide shows you how to install a Trapeze Networks™ Mobility Point™ (MP™) access point in a Trapeze Networks Mobility System™ wireless LAN (WLAN). Read this guide if you are a network administrator or other person installing MP access points in a network.Trapeze Networks Mobility System The Trapeze Networks Mobility System is a system for planning, deploying, and managing a secure wireless LAN (WLAN) in an existing wired corporate network, or as an original greenfield network. The Trapeze system provides connectivity to wireless users in large environments such as office buildings, hospitals, and university campuses, with minimal changes to existing wired networks. Key features of the system are its structured planning tools, ability to grow, authentication based on user identity, redundancy, and secure mobility. The Trapeze Networks Mobility System consists of the following hardware and software:zOne or more Mobility Exchange™ (MX™) switches—distribution points (DPs) for configuring and managing the WLAN, connecting and powering MP access points, and connecting the WLAN to the wired network backbonezMultiple Mobility Point (MP) access points—wireless access points (APs) that transmit and receive radio frequency (RF) signals to and from wireless users and connect them to an MX switchzMobility System Software™ (MSS)—the operating system that runs all MX switches and MP access points in a WLAN, and is accessible through a command-line interface (CLI) or the RingMaster™ graphical user interface (GUI)zRingMaster tool suite—an extensive GUI application for planning, configuring, managing, and troubleshooting a WLAN and its usersTrapeze Networks Mobility System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

DocumentationTrapeze Mobility Point Installation Guide2DocumentationConsult the following documents to plan, install, configure, and manage a Trapeze Networks Mobility System: zRead me first:zTrapeze Regulatory Information. Important safety instructions and compliance information that you must read before installing a unit.zTrapeze Mobility Exchange Quick Start. Graphical aid to getting a Mobility Exchange (MX) switch operational.zInstallation and basic configuration:zTrapeze Mobility Exchange Installation and Basic Configuration Guide. Instructions and specifications for installing an MX switch in a Trapeze Mobility System wireless LAN (WLAN) and deploying basic 802.11 wireless service.zTrapeze Mobility Point Installation Guide. Instructions and specifications for installing an MP access point and connecting to an MX switch.zConfiguration and management:zTrapeze RingMaster Administrator’s Guide. Instructions for planning, configuring, and managing the system with the RingMaster GUI.zTrapeze Mobility System Software Configuration Guide. Instructions for configuring and managing the system through the Mobility System Software CLI.zTrapeze Mobility System Software Command Reference. Functional and alphabetic reference to all Mobility System Software commands supported on MX switches and MP access points.Documentation ConventionsTrapeze documentation uses certain conventions for safety and advisory notices, text and command syntax, and GUI conventions.Safety and Advisory NoticesThe following safety and advisory notices can appear in this manual: Caution! Be careful! This situation or condition can lead to data loss or damage to the product or other property.Warning! Danger! This situation or condition can cause injury.Warning! Danger! High voltage. This situation or condition can cause injury due to electric shock.

Chapter 1: Introducing the Trapeze Networks Mobility System 3DocumentationText and Syntax ConventionsTrapeze manuals use the following text and syntax conventions: Warning! Danger! Radiation. This situation or condition can cause injury due to improper handling of fiber-optic equipment.Note. Take note. This information is of special interest.Convention UseMonospace text Sets off command syntax or sample commands and system responses.Bold text Highlights commands that you enter or items you select.Italic text Designates command variables that you replace with appropriate values, or highlights publication titles or words requiring special emphasis.Menu Name > Command Indicates a menu item that you select. For example, File > New indicates that you select New from the File menu.[ ] (square brackets) Enclose optional parameters in command syntax.{ } (curly brackets) Enclose mandatory parameters in command syntax.| (vertical bar) Separates mutually exclusive options in command syntax.

DocumentationTrapeze Mobility Point Installation Guide4

Chapter 2: MP Overview 5Chapter 2MP OverviewA Trapeze Networks Mobility Point (MP) access point provides 802.11 wireless access to the network. MP access points are designed for use with a Trapeze Networks Mobility Exchange (MX) switch. MP access points require hardware installation only. All configuration for an MP access point takes place on the MX switch. Mobility Point Model NumbersThe MP access point models differ based on the number of 802.11 radios they contain. Table 1 lists the MP access point model numbers. The model number is listed on the product label, located to the right of the cable ports on the bottom of the device.Mobility Point Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5External Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Table 1. MP access point model numbersModel RadiosMP-101 One radio that can be configured for 802.11a or 802.11bMP-122 One 802.11a radio and one 802.11b radioNote. The MP access point radios are disabled by default and can be enabled only by a system administrator using the MX switch.

External Hardware FeaturesTrapeze Mobility Point Installation Guide6External Hardware FeaturesThe external hardware features of MP access points are the same for all models. Figure 1 shows the external hardware features of the MP access point. Figure 1. MP access point—top viewFigure 2. MP access point—bottom viewCable PortsAn MP access point has two RJ-45 ports. (See Figure 2.) Each port provides a 10/100BaseTX Ethernet connection to an MX switch. The MX switch provides power and data to the MP access point through the ports. Use a Category 5 (Cat 5) cable with straight-through signaling and standard RJ-45 connectors to connect the MP access point to the MX switch. Radio 2 LEDHealth LEDRadio 1 LED840-9502-0010UnlockRJ-45 jacks Port 2 Port 1840-9502-0007

Chapter 2: MP Overview 7External Hardware FeaturesThe two RJ-45 ports support dual-homed configurations. In a dual-homed configuration, the MP access point is connected to two separate MX switches. If one MX switch becomes unavailable, the other MX switch continues to provide network access to the MP access point. The ports are identical. You can use either port to connect the MP access point to an MX switch. For more information about dual-homed configurations, see “Connection Options” on page 9.Mounting HardwareThe MP access point has a universal mounting bracket that allows the device to be mounted on any of the following types of surfaces:zSuspended T-bar ceiling, with a bar face measuring 14.2 mm (9/16 inch) or 23.9 mm (15/16 inch)zJunction boxzSolid surface wall or ceilingzTabletopFigure 3 shows the universal mounting bracket.Figure 3. Universal mounting bracketNote. MP access points do not support daisy-chain configurations. Do not connect the MP access point to another MP access point. <<what happens if the user does this anyway? can it cause equipment damage?>>Note. The solid surface mounting option requires Cat 5 cable that does not have strain relief. The other mounting options can use Cat 5 cable with or without strain relief.840-9502-0018Universalmounting bracket Port connectoropeningT-bar flangesScrew holes

External Hardware FeaturesTrapeze Mobility Point Installation Guide8Status LEDsThe MP access point has LEDs that provide status information for the device. Figure 4 and Figure 5 show the locations of the LEDs. Table 2 describes the LEDs. Figure 4. Health and radio LEDSOn model MP-101, radio LED 1 indicates activity for the single radio, which can be configured for 802.11a or 802.11b. On model MP-122, radio LED 1 indicates activity for the 802.11b radio and radio LED 2 indicates activity for the 802.11a radio.Figure 5. 10/100 Ethernet port LEDSRadio 2 LEDHealth LEDRadio 1 LED840-9502-0010Port 2MX LEDPort 1MX LEDPort 2traffic LED Port 1traffic LED840-9502-0009

Chapter 2: MP Overview 9Connection Options.Connection OptionsYou can connect the MP access point to the MX switch in the following configurations:zSingle connection to an MX switchzDual-homed connection to a single MX switchTable 2. MP access point LEDsLED Appearance MeaningHealth Solid green All the following are true:• Management link with an MX switch is operational.• MP access point has booted.• MP access point has received a valid configuration from an MX switch.Solid amber MP access point is waiting to receive boot instructions and a configuration file from an MX switch.Slowly alternating green and amberMP access point is booting with an image received from an MX switch.Quickly alternating green and amberMP access point successfully booted but received an invalid configuration from an MX switch.Port 1 trafficPort 2 trafficGreen 100-Mbps link is operational.Amber 10-Mbps link is operational.Blinking Green Traffic is active on the 100-Mbps link. Blinking Amber Traffic is active on the 10-Mbps link. Port 1 MXPort 2 MXGreen All the following are true:• Management link with an MX switch is operational.• MP access point has booted.• MP access point has received a valid configuration from an MX switch.Blinking Green MP access point is booting with an image received from an MX switch.Amber Link is operational but is not connected to an MP access point port on an MX switch.Radio 1Radio 2Blinking green Association with an 802.11 client is occurring.Blinking and alternating green and amberAssociated client is sending or receiving traffic.Blinking amber Non-associated client is sending or receiving traffic.

Connection OptionsTrapeze Mobility Point Installation Guide10zDual-homed connection to two MX switchesIn dual-homed connections, both paths can be used to exchange control information but only one path is used for data. Spanning Tree Protocol does not run on an MX switch port configured for an MP access point and does not affect traffic flow in a dual-homed configuration. Single Connection to an MX SwitchThe single connection option requires one Cat 5 cable from the MX switch location to the MP access point location. Figure 6 shows an example.Figure 6. Single connection to an MX switchDual-Homed Connection to an MX SwitchDual-homed connection to a single MX switch requires two Cat 5 cables from the MX switch location to the MP access point location. Figure 7 shows an example. Figure 7. Dual-homed connection to an MX switchDual-Homed Connection to Two MX SwitchesDual-homed connection to two MX switches requires one Cat 5 cable from the location of each MX switch to the MP access point location. Figure 8 shows an example.Note. Install the Cat 5 cabling for the MP access point at the installation site before installing the access point itself. During installation, you will need to insert the Cat 5 cable(s) into the MP access point port(s) before attaching the access point to the bracket. MP MX switch840-9502-0050MP MX switch840-9502-0051

Chapter 2: MP Overview 11Connection OptionsFigure 8. Dual-homed connection to two MX switchesMPMX switch MX switch840-9502-0052

Connection OptionsTrapeze Mobility Point Installation Guide12

Chapter 3: Installing an MP 13Chapter 3Installing an MPUnpacking an MPThe shipping carton for an MP access point contains the following items: zOne MP access pointzOne paper mounting template (used for marking cutting areas and screw holes)zOne universal mounting bracketzOne 14.2-mm (9/16-inch) T-bar clampzOne 23.9-mm (15/16-inch) T-bar clampzTwo #6-32 x 1-inch machine screws zTwo #6 sheet metal screws and two drywall anchorszThree adhesive rubber feetzOne copy of the Trapeze Mobility Point Installation Guide (this document)Figure 9 shows the contents of the shipping carton.Unpacking an MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Installation Requirements and Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Installing an MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Verifying MP Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Installation Requirements and RecommendationsTrapeze Mobility Point Installation Guide14Figure 9. MP access point shipping carton contentsBefore you begin installation:1Open the carton and carefully remove the contents, if you have not already done so.2Place the packing materials back in the carton and save the carton.3Verify that you received each item in the previous list. If any item is missing or damaged, contact Trapeze Networks. Installation Requirements and RecommendationsFor best results, follow these requirements and recommendations before installing an MP access point.MX Switch RecommendationTrapeze Networks recommends that you install and configure the Mobility Exchange (MX) switch before installing an MP access point. If the switch is already installed and configured for the MP access point(s), you can immediately verify the cable connection(s) when you plug the cable(s) into the MP access point.Caution! The MP access point is designed for use only with the Trapeze Networks Mobility Exchange (MX) switch. Connecting an MP access point to other power over Ethernet (PoE) devices can damage the equipment.T-bar clampsInstallation guide andmounting templateRubber feetUniversalmounting bracketMounting hardwareMobility point840-9502-0001

Chapter 3: Installing an MP 15Installation Requirements and RecommendationsRadio Safety AdvisoriesWhen you enable the MP radio(s) as part of MX switch configuration, the radios are able to receive and transmit radio frequency energy as soon as you connect the MP(s) to the MX switch. Radio Frequency ExposureFederal Communications Commission (FCC) Docket 96-8 for Spread Spectrum Transmitters specifies a safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC-certified equipment. When used with the proper antennas (shipped in the product), Trapeze Networks MP access point products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1-1991. Proper installation of the MP access point according to the instructions in this manual will result in user exposure that is substantially below the FCC recommended limits.Additional Radio Safety AdvisoriesWarning! Locate the MP access point a minimum of 20 cm (7.9 inches) away from people. This safety warning conforms with FCC radio frequency exposure limits for dipole antennas such as those used in the MP access point.Warning! Do not operate the MP access point near unshielded blasting caps or in an otherwise explosive environment unless the device has been modified for such use by qualified personnel. Warning! Do not touch or move the MP access point when the antennas are transmitting or receiving.Warning! Do not hold any radio device so that the antenna is very close to or touching the face, eyes, or other exposed body part while the device's radio antenna is transmitting.Warning! Before using a wireless device in a hazardous location, consult the local codes, national codes, and safety directors of the location for usage constraints.

Installation Requirements and RecommendationsTrapeze Mobility Point Installation Guide16Cable RequirementsCat 5 cable with straight-through signaling must be installed at the site before you install an MP access point. A single connection requires one cable. A dual-homed connection requires two cables.10/100BaseT straight-through signalling uses the following wiring:Wires 1, 2, 3, and 6 are used for data. Wires 4, 5, 7, and 8 are used for Power over Ethernet (PoE).Mounting an MP access point on a solid surface requires Cat 5 cable that does not have strain relief. For installation on all other surfaces, you can use Cat 5 cable with or without strain relief.For more information about cables, see “Cable Ports” on page 6.Note. The MP access point is intended for indoor use only. Do not install the device outdoors. Warning! Do not connect or disconnect cables or otherwise work with the MP access point hardware during periods of lightning activity. Note. To reduce the possibility of connection interference caused by dust, clean the Cat 5 connector pins before inserting a cable into an MP access point.1 <—> 12 <—> 23 <—> 34 <—> 45 <—> 56 <—> 67 <—> 78 <—> 8

Chapter 3: Installing an MP 17Installation Requirements and RecommendationsInstallation Hardware and ToolsTable 3 lists the mounting hardware and tools required for each type of installation.Table 3. Required mounting hardware and toolsMounting option Required hardware and toolsIncluded with the productSuspended ceiling—flush ceiling tilesMounting template YesUniversal mounting bracket Yes14.2-mm (9/16-inch) T-bar clampNote. T-bar clamp is not required for a 23.9-mm (15/16-inch) T-bar ceiling with flush ceiling tiles.YesBox cutter NoSmall screwdriver (3-mm or 1/8-inch)NoSuspended ceiling—drop ceiling tilesMounting template YesUniversal mounting bracket Yes14.2-mm (9/16-inch) T-bar clamp or 23.9-mm (15/16-inch) T-bar clampYesBox cutter NoSmall screwdriver (3-mm or 1/8-inch)NoJunction box Two #6-32 x 1-inch machine screwsYesUniversal mounting bracket YesSmall screwdriver (3-mm or 1/8-inch)No#2 Phillips-head screwdriver NoSolid wall or ceiling Two #6 sheet metal screws and two drywall anchorsYesUniversal mounting bracket YesHammer NoSmall screwdriver (3-mm or 1/8-inch)No#2 Phillips-head screwdriver No

Installing an MPTrapeze Mobility Point Installation Guide18Figure 10 shows the universal mounting bracket.Figure 10. Universal mounting bracketInstalling an MPTo install an MP access point, use one of the following procedures.Suspended Ceiling Installation—Flush Ceiling Tiles1Select an installation location that is centered over a T-bar in the ceiling.2Cut a hole as follows in the ceiling tile for the Cat 5 cable(s):aPlace the mounting template over the area where you plan to install the MP access point.bUse the box cutter to cut along the line marking the hole for the Cat 5 cable.cRemove the mounting template and the material you cut from the ceiling panel.3Determine whether to install a T-bar clamp onto the ceiling T-bar:zIf the T-bar width is 14.2 mm (9/16 inches), you need to install the 14.2-mm (9/16-inch) T-bar clamp. Go to step 4.zIf the T-bar width is 23.9 mm (15/16 inches), the universal mounting bracket fits directly onto the T-bar. Go to step 5. Tabletop Universal mounting bracket YesThree adhesive rubber feet YesSmall screwdriver (3-mm or 1/8-inch)NoTable 3. Required mounting hardware and tools (continued)Mounting option Required hardware and toolsIncluded with the product840-9502-0018Universalmounting bracket Port connectoropeningT-bar flangesScrew holes

Chapter 3: Installing an MP 19Installing an MP4Install the 14.2-mm (9/16-inch) T-bar clamp onto the ceiling T-bar. aSlide each half of the clamp onto the T-bar so that the clamp lip is fully on the T-bar. bSlide the two halves of the clamp toward each other until the tabs are inserted completely into the holes and the clamp fits snugly on the T-bar.Figure 11. Step 4 (if T-bar width is 14.2 mm (9/16 inches))5Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point, then remove the bracket.Figure 12. Step 5—unlocking the bracket6Install the universal mounting bracket as follows onto the T-bar or T-bar clamp: aPlace the universal mounting bracket against the T-bar or clamp so that the two screw holes face downward and the two T-bar flanges face upward and are adjacent to the T-bar edges. bProperly align the bracket for mounting by placing the bracket so that its port connector opening is to the left of the hole you cut for the cables. cRotate the universal mounting bracket clockwise until the flanges snap into place on the T-bar or clamp.T-barT-bar clampsSlide together840-9502-0003840-9502-0011

Installing an MPTrapeze Mobility Point Installation Guide20Figure 13. Step 6—top view for 23.9-mm (15/16-inch) T-barFigure 14. Step 6—top view for 14.2-mm (9/16-inch) T-barFigure 15. Step 6—bottom viewT-bar(Viewed from above ceiling tiles, looking down.)840-9502-0005Universal mountingbracketT- barT-bar clamps(attachedto T-bar)Universal mountingbracket840-9502-0012(Viewed from above ceiling tiles, looking down.)T-barUniversal mounting bracket840-9502-0004

Chapter 3: Installing an MP 21Installing an MP7Pull the Cat 5 cable(s) about 15 cm (about 6 inches) through the hole in the ceiling tile to create enough slack to insert the cable(s). 8Insert the Cat 5 cable(s) into the connector(s):zFor a single connection, use either connector. They are identical.zFor a dual-homed connection, insert one cable into each connector. 9Lift the MP access point into place on the universal mounting bracket. Make sure the cable feeds properly into the ceiling as you lift and does not become trapped between the access point and the bracket.Figure 16. Step 9—placing the MP access point on the bracket10 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point.Figure 17. Step 10—locking the bracket11 To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side.Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it.840-9502-0002840-9502-0006LockT-bar

Installing an MPTrapeze Mobility Point Installation Guide22If the access point comes off the bracket, relock the device onto the bracket as described in step 9.12 Go to “Verifying MP Health” on page 32.Suspended Ceiling Installation—Drop Ceiling Tiles1Select an installation location that is centered over a T-bar in the ceiling.2Cut a hole as follows in the ceiling tile for the Cat 5 cable(s):aPlace the mounting template over the area where you plan to install the MP access point.bUse the box cutter to cut along the line marking the hole for the Cat 5 cable.cRemove the mounting template and the material you cut from the ceiling panel.3Install the T-bar clamp that fits the T-bar: aSlide each half of the clamp onto the T-bar so that the clamp lip is fully on the T-bar. bSlide the two halves of the clamp toward each other until the tabs are inserted completely into the holes and the clamp fits snugly on the T-bar.Figure 18. Step 3—installing the T-bar clamp4Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point, then remove the bracket.T-barT-bar clampsSlide together840-9502-0003

Chapter 3: Installing an MP 23Installing an MPFigure 19. Step 4—unlocking the bracket5Install the universal mounting bracket as follows onto the T-bar clamp: aPlace the universal mounting bracket against the T-bar clamp so that the two screw holes face downward and the two T-bar flanges face upward and are adjacent to the T-bar edges. bProperly align the bracket for mounting by placing the bracket so that its port connector opening is to the left of the hole you cut for the cables. cRotate the universal mounting bracket clockwise until the flanges snap into place on the T-bar clamp.Figure 20. Step 5—top view840-9502-0011T- barT-bar clamps(attachedto T-bar)Universal mountingbracket840-9502-0012(Viewed from above ceiling tiles, looking down.)

Installing an MPTrapeze Mobility Point Installation Guide24Figure 21. Step 5—bottom view6Pull the Cat 5 cable(s) about 15 cm (about 6 inches) through the hole in the ceiling tile to create enough slack to insert the cable(s). 7Insert the Cat 5 cable(s) into the connector(s):zFor a single connection, use either connector. They are identical.zFor a dual-homed connection, insert one cable into each connector. 8Lift the MP access point into place on the universal mounting bracket. Make sure the cable feeds properly into the ceiling as you lift and does not become trapped between the access point and the bracket.Figure 22. Step 8—placing the MP access point on the bracket9Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point.Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it.T-barUniversal mounting bracket840-9502-0004840-9502-0002

Chapter 3: Installing an MP 25Installing an MPFigure 23. Step 9—locking the bracket10 To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side.If the access point comes off the bracket, relock the device onto the bracket as described in step 9.11 Go to “Verifying MP Health” on page 32.Junction Box Installation1Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point, then remove the bracket.Figure 24. Step 1—unlocking the bracket2Attach the universal mounting bracket to the junction box:aPlace the universal mounting bracket against the junction box so that the two screw holes face the junction box and align over the screw holes in the box.bInsert the #6-32 x 1-inch machine screws in the universal mounting bracket’s screw holes, and use a #2 Phillips-head screwdriver to tighten them. 840-9502-0006LockT-bar840-9502-0011

Installing an MPTrapeze Mobility Point Installation Guide26Figure 25. Step 2—placing the bracket on the junction box3Pull the Cat 5 cable(s) about 15 cm (about 6 inches) out of the junction box to create enough slack to insert the cable(s) into the port connectors. 4Insert the Cat 5 cable(s) into the connector(s): zFor a single connection, use either connector. They are identical.zFor a dual-homed connection, insert one cable into each connector. 5Lift the MP access point into place on the universal mounting bracket. Make sure the cable feeds properly into the junction box as you lift and does not become trapped between the access point and the bracket.6Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point.Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it.840-9502-0017Junction box

Chapter 3: Installing an MP 27Installing an MPFigure 26. Step 6—locking the bracket7To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side.If the access point comes off the bracket, relock the device onto the bracket as described in step 9.8Go to “Verifying MP Health” on page 32.Solid Wall or Ceiling Installation1Prepare two holes in the wall or ceiling for the universal mounting bracket, using the following steps: aPlace the paper mounting template over the location where you want to install the MP access point.bMark the locations for the screw holes. cRemove the template.2Install the drywall anchors in the holes:aHammer the drywall anchors into the holes, up to the beginning of the threads on the anchors.bScrew the anchors the rest of the way into the holes using a #2 Phillips-head screwdriver.cRemove the screws and save them for step 5.3Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point, then remove the bracket.Note. The solid surface mounting option requires Cat 5 cable that does not have strain relief. The other options can use Cat 5 cable with or without strain relief.840-9502-0006LockT-bar

Installing an MPTrapeze Mobility Point Installation Guide28Figure 27. Step 3—unlocking the bracket4Align the universal mounting bracket over the holes so that the screw holes face toward the screw holes.5Insert the #6 sheet metal screws into the screw holes, and tighten them to secure the universal mounting bracket to the wall or ceiling.Figure 28. Steps 4 and 5—bracket placement on solid wall or ceiling6Insert the Cat 5 cable(s) into the connector(s):zFor a single connection, use either connector. They are identical.zFor a dual-homed connection, insert one cable into each connector. 7Rest the cable(s) in the crevice(s) next to the port connector(s) so that the cables fit between the MP access point and the universal mounting bracket. The cable is too thick to fit between the universal mounting bracket and the MP access point unless you place the cable in the crevice.8Place the MP access point onto the universal mounting bracket, making sure the cables remain in place in the apertures next to the port connectors.840-9502-0011840-9502-0014Drywall anchors(inserted into wall)Universalmounting bracket

Chapter 3: Installing an MP 29Installing an MPFigure 29. Steps 7 and 8—bracket alignmentFigure 30. Steps 7 and 8—cable placement9Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point.Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it.840-9502-0015840-9502-0016Universal mounting bracketCrevice Cable

Installing an MPTrapeze Mobility Point Installation Guide30Figure 31. Step 9—locking the bracket10 To ensure that the MP access point is fully locked onto the bracket, gently pull on the access point and attempt to rotate it from side to side.If the access point comes off the bracket, relock the device onto the bracket as described in step 9.11 Go to “Verifying MP Health” on page 32.Tabletop Installation1Reverse the universal mounting bracket: aUnlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point, then remove the bracket.Figure 32. Step 1a—unlocking the bracketbTurn over the universal mounting bracket, then align the bracket over the cable ports and the four mounting posts.840-9502-0006LockT-bar840-9502-0011

Chapter 3: Installing an MP 31Installing an MPFigure 33. Step 1b—reversing the bracketcOnce the bracket is fully seated, lock the bracket onto the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point.Figure 34. Step 1c—locking the bracket2Attach the three rubber adhesive feet onto the universal mounting bracket, in the three location circles. 3Insert the Cat 5 cable(s) into the connector(s):zFor a single connection, use either connector. They are identical.zFor a dual-homed connection, insert one cable into each connector. 840-9502-0008840-9502-0006LockT-bar

Verifying MP HealthTrapeze Mobility Point Installation Guide32Figure 35. Steps 2 and 3—installing the rubber feet4Place the MP access point in the desired location on the table.5Go to “Verifying MP Health” on page 32.Verifying MP HealthAfter you install the MP access point, you can easily verify its status by observing the LEDs, particularly the health LED. For the location of the health LED, see Figure 9 on page 14.The health LED indicates whether the MP access point is ready for operation. zIf the health LED is green and is glowing steadily, the MP access point has been booted successfully by the MX switch and is ready for operation. zIf the health LED is not steadily glowing green, contact the system administrator for the MX switch. If you are the system administrator, see Appendix A, “MP Troubleshooting,” on page 33.840-9502-0013

Appendix A: MP Troubleshooting 33Appendix AMP TroubleshootingAfter you insert the Cat 5 cable(s) into the MP access point’s port connectors, observe the device’s health LED to determine the status of the connection with the MX switch(es). zIf the health LED is green and is glowing steadily, the MP access point has been booted successfully by the MX switch and is ready for operation. zIf the health LED is not steadily glowing green, see Table 4.For descriptions of all the LEDs, see “Status LEDs” on page 8.Table 4. Health LED statesHealth LED appearance Diagnosis RemedyUnlit MP access point is not receiving power.Check the Cat 5 cable connection with the MX switch(es).Set the port type on the MX switch to an MP port. Verify that power over Ethernet (PoE) is enabled on the MX switch port connected to the MP access point.Slowly alternating green and amberMP access point is booting with an image received from an MX switch.Wait a few seconds for the boot process to complete.Quickly alternating green and amberMP access point successfully booted but received an invalid configuration from an MX switch.Check the MP access point configuration commands in the configuration file to make sure they are compatible with the MP access point. For example, make sure the model is correct.Solid amber MP access point is waiting to receive boot instructions and a configuration file from an MX switch.Wait a few seconds for the boot process to begin. If the LED remains amber, try the remedies for the other health LED appearances. If the LED still remains amber, make sure the MP access point is really connected to an MX switch. Check the Port 1 MX and Port 2 MX LEDs. If one of them is amber, the MP access point is receiving power but is not connected to an MX switch.

Trapeze Mobility Point Installation Guide34

Appendix B: MP Technical Specifications 35Appendix BMP Technical SpecificationsThis appendix lists the technical specifications for the Trapeze Networks MP access point. Table 5 lists the mechanical and compliance specifications. (For detailed compliance information, see the Trapeze Regulatory Information document.) Table 7 and Table 6 list the radio specifications.Note. For specifications for the Mobility Exchange (MX) switch, see the Trapeze Mobility Exchange Hardware Installation and Reference.Note. The MP access point radios are disabled by default and can be enabled only by the system administrator using the RingMaster™ management application or the MX switch’s command-line interface (CLI). Note. The radio frequency band, operating channels, and transmit power depend on the country of operation specified by the system administrator using RingMaster or the MX switch’s CLI.Table 5. MP mechanical and compliance specificationsSpecification DescriptionSize Diameter: 16.76 cm (6.6 inches)Height: 4.69 cm (1.85 inches)Note. The universal mounting bracket adds <<how many?>> cm (<<how many?>> inches) to the height.Weight Without mounting bracket: 0.35 kg (12.5 ounces)With mounting bracket: 0.40 kg (14 ounces)Operating Temperature 0° C to +50° C (32° F to +122° F)

Trapeze Mobility Point Installation Guide36Storage Temperature -30° C to +75° C (-22° F to +167° F)Humidity 10% to 95% noncondensingPower over Ethernet (PoE) 41 VDC to 49 VDC (46 VDC nominal)12 W to 15.3 WStatus indicators Seven LEDs (For descriptions of the LEDs, see “Status LEDs” on page 8.) Wired network ports Two RJ-45 ports for 10/100BaseT Ethernet and power over Ethernet (PoE)Standards compliance IEEE 802.11aIEEE 802.11bSafety and electromagnetic complianceFCC OET-65 and ANSI C95.1-1991ETS 300 328 (2.4 GHz) and 301 893 (5 GHz)FCC Part 15EMI Class BCFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4)ICES-003RSS-139-1 and RSS-210R&TTE Directive 1999/5/ECEncryption 40-bit/128-bit Wired Equivalency Privacy (WEP)Temporal Key Integrity Protocol (TKIP)Wi-Fi Protected Access securityAdvanced Encryption Standard (AES) readyGeneral Wi-Fi CERTIFIEDPower-save mode supportedTransmit power controlSupports up to 500 clientsTable 6. 802.11a radio specificationsSpecification DescriptionAntenna type Integrated omnidirectional diversity antennasAntenna gain 2 dBi Frequency band 5.15 GHz to5.85 GHz based on country regulationsOperating channels Based on the country of operation specified by the system administratorAssociation rates 54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps, and 6 Mbps, with automatic fallbackTable 5. MP mechanical and compliance specifications (continued)Specification Description

Appendix B: MP Technical Specifications 37Modulation Orthogonal frequency division multiplexing (OFDM)Transmit power Based on the country of operation specified by the system administratorTable 7. 802.11b radio specificationsSpecification DescriptionAntenna type Integrated omnidirectional diversity antennasAntenna gain 2 dBiFrequency band 2.4 GHz to 2.4835 GHz based on country regulationsOperating channels Based on the country of operation specified by the system administratorAssociation rates 11 Mbps, 5.5 Mbps, 2 Mbps, and 1 Mbps, with automatic fallbackModulation Direct-sequence spread-spectrum (DSSS)Transmit power Based on the country of operation specified by the system administratorTable 6. 802.11a radio specifications (continued)Specification Description

Trapeze Mobility Point Installation Guide38

Navigation menu