LEOPHILE Technology IMPULSE Bluetooth Headset User Manual EEL M14

LEOPHILE Technology Co., Ltd Bluetooth Headset EEL M14

user manual

Do not use earphone in thunderstorm weather, the earphone may not work properly in the condition, and increase the risk of being hitby lightning . Hard resetRING COLLARMUSIC WIRELESS HEADSETIf the earphone cannot be turned on even when fully charged or does not respond during use, follow the instructions below to reset it.1.While pressing and holding the multifunction button, connect the earphone to your PC’s USB port or a USB power adapter with the charging cable. 2.Keep pressing and holding the Multifunction button until the earphone turns on. The earphone is now reset.LEOPHILE IMPULSE INSTRUCTIONMusicMusic play / pausePress Multifunction button once to play / pause music. (Some phones may require you to start a media player first) .Track back/forward Press the Volume "-" for 2 seconds once to skip track backward, press Volume "+" for 2 seconds once to skip track forward. Switch Music and Call When a call rings during a music playing, the music automatically pauses to allow you to answer or ignore the call. Once the call is ignored or ends, the music is resumed.(Need media player support).Clear paired listMake sure the earphone is turned off, press and hold the Multifunction button until the LED indicator flashes red and blue alternately (About 7seconds), then release Multifunction button. Press volume "+" and volume "-" button at the same time until LED flashes blue, then LED flashes red and blue alternately, the paired list was cleared, the earphone will enter pairing mode after power on next time.Redial the last callMute on/offDouble-press multifunction button in standby mode or streaming.The mobile phone will redial the last call number.Press the Volume "-" for about 2 seconds to mute on/off.Voice dial (Need phone support)In standby mode press and hold the multifunction button for about 2 seconds wait for phone prompt and then tell the phone to dial the name of a stored contact.Switch between the earphone and phonePress the multifunction button for about 2 seconds during a call, the call will be switched to the mobile phone, redo this operation again, the call will be switched to the earphone. CallAnswer a callPress the Multifunction button or Volume "+" or Volume "-" once.Reject a callPress and hold the Multifunction button for about 2 seconds.Press the Multifunction button once.End a callReject the new call hold the current callDuring the call there is a new call, press and hold the multifunctionbutton for about 2 seconds to reject a new call, keeping the active call.End current call and answer new callWhen a new call rings during a call, press the Multifunction button once to answer new call and end current call simultaneously.On hold current call and answer new callWhen a new call rings during a call, Double the Multifunction button to hold current call and answer new call. BluetoothONSe arc hLEO PHILE I MPULS EWindows Phone 8a. On your phone, open the Settings menu.b. Select Bluetooth. If Bluetooth is off, turn it on. The Phone will search for new devices automatically.Safety and careUsing earphone at high to moderate volumes for extended periods of time will result in permanent hearing damage .It is advised youkeep volume levels moderate to low at all times for your safety. Do not use any corrosive cleaner/oil to clean the earphone.If the earphone comes in contact with liquids, quickly wipe away .If submersed in water, do not turn the earphone on until completely dried.Tips: liquid submersion voids the warranty.Keep the earphone and packaging out of reach of children .Enable voice prompts: enter pairing mode: Press the volume "+" button for 3 seconds, the blue LED lights flash 3 times;Disable voice prompts: enter pairing mode: Press the volume"-" button for 3 seconds, the red LED lights flash 3 times. Do not use while driving a car, cycling, operating machinery, or performing other activities that require hearing surrounding sounds.Earphone may not work properly under high temperature or high humidity conditions.504.00 mm76.00 mmPair one phonePairingiPhonea.On your phone, open the Settings menu.b.Select Bluetooth. If Bluetooth is off, turn it on. The iPhone will search for new devices automatically.Android phonea.On your phone, open the Settings menu.b.Select Bluetooth (For old Android phone, Bluetooth is found in the Wireless & Networks). If Bluetooth is off, turn it on. Select Search for Devices if your phone does not automatically search for new devices.Note: When the earphone and phone have been paired once, they will automatically connect when the earphone is on and Bluetooth is activated on the phone.Following items are includedStart hereUSB cableEar cushionsBasic operationStatus indicatorInstructionPower onPower offStandbyIncoming callPairingLED statusStay blue about one secondStay red about two secondsFlashes blue quicklyFlashes red and blue alternatelyVoice prompts Power onPower off/TootBattery lowBattery low Blink red Charging Stays on red while charging /Volume up/down Press the volume "+" to turn volume upPress the volume "-" to turn volume down Power onPower offPress and hold Multifunction button for about 3 seconds. The earphone says "power on" and the LED flashes blue one secondPress and hold Multifunction button for about 5 seconds. Theearphone says "power off" and the LED flashes red two seconds.Tips: When the distance between the earphone and phone is beyondeffective range, earphone disconnects with phone. Earphone will power off automatically once no active for 15 minutes.Stays on blue after fully charged.Blink blue once every 5 secondsProduct overview1. Volume + / Track forward 2. Charge jack 3. Status indicator 4. Talking mic5. Multifunction button6. Volume - / Track back3. Select "LEOPHILE IMPULSE". If your phone asks, enter 0000 (four zeros) for the Pass code or accept the connection. The LED indicator stops flashing red and blue once successfully paired, you hear "Connection successful". Some phone list an option to "Play through earphone", select to use theearphones.BluetoothONSe arc hLEO PHILE I MPULS EPair another phoneMultipoint technology enables you to pair another phone and take a call from either.To paired first smart phone power off the headset , then power on and paired the second phone and then power off and restart the headset, it will reconnect to second paired phone automatically for the first pairedphone link, your shall manual operation from the 1st smart phone's bluetooth has paired list menu and select and click the "LEOPHILE IMPULSE"Blu etoo thONCon nectLEOP HILE IM PULSEONCon nectLEOP HILE IM PULSEBl ueto othCalling switchWhen the first phone call rings, press the Multifunction buttononce to answer the call, if the seconds call rings at this moment,you can answer the second phone by double click Multifunction button, and on hold the first phone call.Charging Your new earphone has enough power to pair and make a few calls. It takes 2 hours to fully charge the earphone; while charging, the battery indicator light is red, the indicator light flashes blue once charging is complete. Note: The lifetime of the battery will be significantly reduced if your earphone is left uncharged for a long period. We recommend that you recharge your earphone at least once a month. 1.After power on,if has PDL,it will reconnect , if fail, earphones automatically enter pairing mode (the LED indicator flashes red and blue alternately).2.Activate on your phone (See below for more details).Bluetooth/LEOPHILE
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu