NINGBO CSTAR IMP and EXP 0051 Bluetooth earbuds with charging case User Manual CT182029 Instructions 10 23

NINGBO CSTAR IMP&EXP; CO., LTD Bluetooth earbuds with charging case CT182029 Instructions 10 23

Users Manual

55mm70mmFrontBackQUICK START GUIDETRUE WIRELESS EARBUDS GETTING STARTED7231654RL1 Micro USB charging port2 Charging Case LED indicators3 Charging Case Power Button4 Left earbud LED indicator5 Left control button6 Right earbud LED indicator7 Right control buttonLLeft Earbud Right EarbudRPause/Play/Answer Call/End Call, Next Track/— Charge on the go charging case, with the included micro USB cable for 2-3 hours. (LED (2A) will blink red) Do not charge longer than suggested time. Do not charge overnight.— When LED (2A) is illuminated solid red battery case is fully charged.Charging LED IndicatorsCHARGING YOUR CASE2A 2B2A 2BFlashing RED- Battery Case is chargingSolid RED- Battery Case is fully chargedSolid BLUE- Battery Case is charging earbudsOFF- Battery Case is offCHARGING YOUR EARBUDS— Place Right and Left Earbuds in battery case charging cradle and press the power button on the battery case (3) — Charging case LED indicator (2B) will illuminate Blue and the earbud LED indicators (4, 6) will illuminate Red, indicating that the earbuds are charging properly. When Earbuds LEDs (4, 6) turn solid blue, earbud batteries are fully charged.— After earbuds are fully charged, press the charging case power button (3) to turn the charging case OFF.MONO MODE(SINGLE EARBUD USE)— Remove earbud from charging cradle and power on by pressing the control button (7) or (5) for 3 seconds depending on which earbud your using.— Once earbud is powered on, proceed to PAIRING— Remove both earbuds from charging cradle and place them in your ears.— Make sure Bluetooth® Search Mode is turned off on your mobile device.— Hold the right earbud button (7) for 3 seconds and then press left earbud button (5) for 3 seconds until they are powered on. (Earbud LEDs will flash Red and Blue to indicate that they are in Link mode.)— Earbuds will automatically link together aftera few seconds,and earbuds will have a tone(LEDs will flash blue) — Once Earbuds are linked together you may proceed to pairing with your mobile device.STEREO MODE(DUAL EARBUD USE)PAIRING*Note: Once earbuds have been initially paired successfully with your mobile device they will automatically pair the next time — Enable Bluetooth search mode on your mobile device and search for pairing name “ EB43 ” and select it on your mobile phone. Once the earbuds are successfully paired a notification will sound . — Now you can enjoy your true wireless Bluetooth Earbuds.TWS-i7OPERATING BLUETOOTH EARBUDSFunction OperationPower On Press (5) or (7) for 3 secondsPower Off Press (5) or (7) for 5 secondsPlay/Pause Single press (5) or (7)AnswerReject Earbuds LED indications (4) & (6)Power On Red and Blue LED will flash altematelyLink Mode Flashing Blue + RedPaired Successfully Flashing Blue Power Off LED OffEarbuds in Cradle Charging Solid RedFully Charged Solid BlueCharging Case See CHARGING YOUR CASESingle press (5) or (7)Press (5) or (7) for 2 secondsthey are powered on.Model:EB43
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference.(2)This device must accept any interference received, including interference that maycause undesired operation.2. Changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Note:This equipment has been tested and found to comply with the limits for a class Bdigital device,pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequence energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not accor in a particular installation.if this equipmemt does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.• Connect the equipment into an autlet on a circuit different from that to which the receiver is connectec.• Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Navigation menu