Ningbo Pdlux Electronic Technology PD-V8 Microwave Sensor User Manual SIR13 installation instructions2

Ningbo Pdlux Electronic Technology CO.,LTD. Microwave Sensor SIR13 installation instructions2

User Manual

Installation Instructions P D - V 81) Provide 5V DC on pad 1 (4.75V-5.25V)2) Provide DC ground onto PAD33) Connect PAD 2 (IF) to the µPC for signal processing4) Operating temperature: -10-70°CPAD1 PAD3 PAD2 The use of the transceiver is authorized into mobile or fixed devices taking intoaccount the conditions listed below :• OEM Integrator may be sure that the end user manual may not contain anyinformation about the way to install or remove the module from the finalproduct.Microwave Sensor
• Depends on final host configuration additional authorization requirements forthe non-transmitter functions on the transmitter module may be required (i.e.,Verification, or Declaration of Conformity) OEM integrator is responsible forensuring that after the module is installed and operational into the host, itcontinues to be compliant with the Part 15B unintentional radiatorrequirements.• The information on label and user manual is required to be incorporated in theuser manual of the final system. see 47 CFR15 requirements for more details(e.g. 15.19 / 15.21 / 15.101 / 15.105 / RSS-GEN / ICES)• Additional label with the words ‘Contains FCC ID:2AIWWPD-V8 and ‘ContainsIC:20845-STACK102’ shall be applied and visible from the outside of the endproduct.• The module must be installed and used in strict accordance with themanufacturer’s instructions as described in the user documentation thatcomes with the product.• The antenna of the module may not be removed, replaced nor modified. Theantenna must not be co-located or operating in conjunction with any otherantenna or transmitter. No additional antenna must be used.20X12mmMicrowave SensorIC:20845-STACK102FCC ID:2AIWWPD-V8MODEL:PD-V8Microwave SensorIC:20845-STACK102FCC ID:2AIWWPD-V8MODEL:PD-V8
FCCCaution.Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.AnyChangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:‐Reorientorrelocatethereceivingantenna.‐Increasetheseparationbetweentheequipmentandreceiver.‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Navigation menu