SAGEMCOM BROANDS FAST5260CV FAST 5260CV Home Router User Manual Safety sheet Fast 5260CV

SAGEMCOM SAS FAST 5260CV Home Router Safety sheet Fast 5260CV

Contents

User Manual Safety sheet Fast 5260CV.pdf

Safety and Certifications 253541042-C 29 October 2014 4 Safety and Certifications 253541042-C 29 October 2014 1 Important Information about the Sagemcom F@st 5260CV: Installation and Safe Usage Instructions: 1. Place the router in a vertical orientation on a flat surface. 2. Connect the manufacturer supplied AC to DC power adapter. The F@st 5260CV router requires the use of a 12 VDC, 2.5 A power adapter. Only use a manufacturer supplied and approved power adapter and Ethernet cable. 3. Connect the F@st 5260CV to the AC Mains in accordance with the installation instructions in this booklet, and the markings on the identification label (voltage, current, and frequency of electricity network). 4. Connect the Ethernet cable (provided) to one of the RJ45 ports on the Router labeled "1", "2", "3", or "4". Then connect the other end of the Ethernet Cable to the Ethernet port of a computer. Repeat as necessary for the other available Ethernet ports. 5. For an Ethernet WAN configuration, connect the RJ45 port labeled “wan” to the connection provided by your ISP. When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons including the following: 1. Do not use this product near water and avoid contact with moisture. For example, do not use near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that liquids are not spilled on this equipment. 2. This equipment is for indoor use only, do not place or install in an outdoor location. 3. Place your product on a firm, solid surface, no obstacle at a minimum distance of 30 cm (0.98 ft). If you put it on something unsteady, it may fall and be damaged. If you place it on a soft surface, such as rug, sofa or cushion, the vents may be blocked, causing the product to overheat. 4. Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or fire. 5. As the power adapter is the only way to connect to the electrical network, the product must be installed near an easily accessed power outlet. 6. This equipment should only be operated from the type of power supply (Voltage and Current) indicated on the marking label. 7. Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or electrical shock. 8. Avoid blocking any vent openings or exhaust exits on this equipment. Do not place equipment in a built-in installation such as a cabinet that may impede the flow of air through the ventilation openings. 9. The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other heat producing appliances and equipment. 10. Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by items placed upon or next to it. 11. Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning only. 12. This equipment is not user serviceable and is to be serviced by qualified personnel only. Do not disassemble this equipment. If service is required, disconnect all power from the equipment and consult qualified service personnel. 13. To disconnect this equipment from AC power, unplug the power supply from the AC wall socket. 14. Connect only to in house equipment (SELV interface). It is not allowed to connect to public cable distribution or cable television network. 15. Use the product in the environment specified as below: - Air temperature between 0 °C and + 40 °C. - Relative humidity between 20 % and 90 %. - Altitude: 2000 meters (6562 ft) maximum. Save these Instructions!
Safety and Certifications 253541042-C 29 October 2014 2 Federal Communications Commission (FCC) Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Modifications: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC Responsible Party: Sagemcom USA 14651 N. Dallas Parkway Suite 900 Dallas, TX 75254 Phone: 972-674-4100 Radio Frequency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device produces radio frequency energy in the 2.4 GHz and 5 GHz spectrums. The antenna must be positioned to keep a minimum distance of 30 cm (0.98 ft) from the radiating element to any nearby person. Issued by Sagemcom Broadband SAS Sagemcom 250, route de l'Empereur - 92848 RUEIL MALMAISON CEDEX FRANCE © Sagemcom Broadband SAS 2013 All rights reserved. Subject to availability. Rights of modifications reserved. www.sagemcom.com Safety and Certifications 253541042-C 29 October 2014 3 Wall Mounting Router (Optional) While many users place their F@st 5260CV series gateways on their desk, it can be optionally wall mounted. 1. The unit is wall mounted with the top of the unit facing up. 2. Ensure that the wall you use is smooth, flat, dry, and sturdy. 3. The unit is mounted using two M3x20 screws (20mm length and 3mm in diameter). 4. Install the two screws 135 mm (5.3 inches) apart approximately 20 mm (0.8 inches) below the desired top of the unit per the following figure. 5. Screw the screws into the wall leaving their heads extending approximately 3.5 to 4.0 mm (0.15 inch) from the wall surface. 6. Carefully align the screw heads in the keyholes on the back of the unit and gently push it onto the wall moving it downward to secure it in the narrow portion of the keyhole slots.

Navigation menu