SAT AMERICA LI102W BARCODE SCANNER User Manual user manual

SAT AMERICA INC BARCODE SCANNER user manual

user_manual

*Real-me modeUpload dataData sumClear DataNo. :1230105001 v2.0Quick Start GuideFollowing working mode can be set directly.Cache modeInventory modeNote:Real me mode: Scan and transmit data will automacally lost if upload failed.Cache mode: Same as real me mode if connecon normal. Scan bar codes will be automacally restore if connecon failed. Will upload one by one if connecon return as normal.Inventory Mode: Scanning bar codes will be restored without upload.Will upload once scan “Upload data”barcode.Will clear once scan“Clear data”.Will check sum once scan”Data sum”.The best distance6～15CM121311113 121311113Correct WrongNOTE: LED beam should be full coveraged on the bar codeUpload data: Bar code data will transmit to terminal once scan this bar code.Date sum: Scan “Data sum”bar code to check the scanner restore data sum.Clear data: Scan“Clear data” and clear all the restore data in scannerContents:● Barcode Scanner ●Cradle ● Quick Start Guide ● USB / RS232 Cable ● Power Adapter (Rs232 only ) 2 Cable plug&Unplug② Press the buckle click, then pull out the cableScannerTrigger BuonScanning windowLED IndicatorBuzzarCradle LED IndicatorCardle1 Scanner overview ① Plug as picture above（1）USB Data cable （2）RS232 Data cable ①②5 Charging methodFirst step: Insert the cradle as above picture. the green light of the cradle will connue（ on not able to pair when green light flashing.）Second step: Aer insert the cradle , it must be scan the below bar code within 20sPair in one stepFollowing working mode can be set directly.3 Cable connection guide Scanning method and distance4Pairing Guide Inventory mode settingTransmitter(Scanner)Working mode：Method1D Barcode Scanner1DModel No.: SAT LI102W
500ms（F0205）1000ms（F0210）Disable repeat read（F0100）*Enable repeat read （F0101）Mulple read（F0102）Mulple read: The same label can only be decoded again aer the label has not been detected for a number of scans. This mode can only be programmed in Connuous read trigger mode.Disable auto trigger（H0000）* Enable auto trigger（H0001）LightLED Status DescriponScannerGreen light on Power on/ Working normallyRed light blinks Pairing matchGreen light blinks once Upload successfullyGreen light blinks twice Upload failedRed light on Low baeryBlue light on Charging normalGreen light on Charging completeGreen light blinking Pairing unsuccessfulRed light on USB idenfy failed Green light blinks once Green light on Working normallyUploaded successfullyCradleGreen light blinks 30s Pairing state Scan the bar code of “Enter seng”Enter SengScan the funcon bar codesScan the bar code of “Exit and Save”Exit and SaveSeng Step123③ Dalay for repeating to read the same barcode② Reading Mode④ Auto trigger（optional）Set up process：❶Scan the bar code of“Enter Setting”.❷Scan the bar code of "Custom Suffix".❸Scan one of bar code below as suffix❹Scan the bar code of “Exit and Save”.Enter SengCustom SuffixExit and SaveNone*0x0D （CR）0x0A （LF）TAB③ Suffix②Numeric Keypad Enable Numeric Keypad*Disable Numeric KeypadConfiguraon method: Scan the funcon bar code directly.Single decode: When a bar code has been decoded, the reader will be turned off. The reader must be triggered again to read another label.Connuous decode: The reader will produce as much data as it can decode regardless whether it is the same or not. This mode is mainly used for demonstraon and diagnosis. ① Trigger Mode*Single ReadConnuous Read❷Scan one of the bar code below as sleep me.Sleep Time60s 5min 30min20S3min 15min None sleep❸Scan the bar code of “Exit and Save”.The sleep me means the me between the last operaon move and auto turn off the scanner. User able to scan the corresponding bar code of the sleep me which is needed to accomplish the sleep me seng.④Sleep Time SettingSet up process：❶Scan the bar code of“Sleep Time”.This part is valid for wireless sengs onlyEnter SengExit and SaveSet up process：❶Scan the bar code of“Enter Setting”.❷Scan the bar code of “Restore Defaults”.Restore Defaults❸Scan the bar code of "Exit and Save".The default seng allows the scanner to be restored to the factory seng state.①Defaults ParameterExit and Save Decode SettingsWierless SettingsThis part is valid for decode sengs only2000ms（F0220）FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Navigation menu