SZ DJI TECHNOLOGY WM3221510 Phantom 3 Advanced User Manual Part Three

SZ DJI TECHNOLOGY CO., LTD Phantom 3 Advanced Users Manual Part Three

Contents

Users Manual Part Three

© 2015 DJI. All Rights Reserved. 31Gimbal CameraCamera and Gimbal CameraProleThe on-board camera supports 4K video capture up to 4096 x 2160p24 and 12M pixel photos capture by using the 1/2.3 inch CMOS sensor. You may export the video in either MOV or MP4 format for editing. Available picture shooting modes include burst, continuous, and time-lapse mode. A live preview of what the camera is seeing before you shoot videos and pictures is supported through the DJI Pilot App. Camera Micro-SD Card SlotTo store your photos and videos, plug in the Micro-SD card into the slot shown below before powering on the Phantom 3 Advanced. The Phantom 3 Advanced comes with a 16 GB Micro-SD card and supports up to a 64 GB Micro-SD card. A UHS-1 type Micro-SD card is recommended, because of the fast read and write capability of these cards enables you to store high-resolution video data. Do not remove Micro-SD card from the Phantom 3 Advanced when it is powered on. Camera Data PortPower on the Phantom 3 Advanced and then connect a USB cable to the Camera Data Port to down-load photos or videos from the camera to your computer. Power on the aircraft before attempting to access the les on the Micro-SD card.
32 © 2015 DJI. All Rights Reserved. Gimbal CameraPhantom 3 Advanced User ManualCamera OperationUse the Shutter and Record button on the remote controller to shoot the images or the videos through the DJI Pilot app. For more information about how to use these buttons, refer to “Controlling Camera”. GimbalGimbalProleThe 3-axis Gimbal provides a steady platform for the attached camera, allowing you to capture stabilized images and video. The Gimbal can tilt the camera up to 120 degrees.Use the gimbal dial on the remote controller to control pitch movement of the camera by default. Note that you cannot control the pan movement of the camera by default. Gimbal Operation ModesTwo Gimbal operation modes are available. Switch between the different operation modes on the Camera page of the DJI Pilot App. Note that your mobile device must be connected to the remote controller for changes to take effect. Refer to the table below for details: Follow Mode The angle between Gimbal’s orientation and aircraft’s nose remains constant at all times. One user alone can control the pitch motion of the gimbal.FPV Mode The Gimbal will lock to the movements of the aircraft to provide a First-Person-View ying experience. Gimbal motor error may occur in these situations: (1) Gimbal is placed on uneven ground. (2) Gimbal has received an excessive external force, e.g. a collision. Please take off from at, open ground and protect the gimbal after powering up. Flying in heavy fog or cloud may make the gimbal wet, leading to a temporary failure. The gimbal will recover when it dries out. -90°0°30°
© 2015 DJI. All Rights Reserved. 33Gimbal CameraPhantom 3 Advanced User Manual ②①③Anti-drop KitThe Anti-drop Kit helps keep the gimbal and camera connected to the aircraft. Two have been mounted on delivery. If new ones are required, take the gimbal and press part [1] through the center hole of the Vibration Absorber the center hole of part [2]. Lock them together as shown in [3]. Mounting the Anti-drop Kit diagonally is recommended.
34 © 2015 DJI. All Rights Reserved. DJI Pilot App This chapter introduce the four main sections of the DJI Pilot app.
© 2015 DJI. All Rights Reserved. 35DJI Pilot App DJI Pilot AppThe DJI Pilot app is a mobile app designed specically for the Phantom 3 Advanced. Use this app to control the gimbal, camera and other features of your ight system. The app also comes with Map, Acad-emy and User Center, for conguring your aircraft and sharing the photos and videos with your friends. It is recommended that you use a tablet for the best experience.CameraThe Camera page contains a live HD video feed from the Phantom 3 Advanced’s camera. You can also congure various camera parameters from the Camera page. CAMERA ACADEMY USER CENTERMAPUnited StatesMountain View1/320 4821JPEG 4K 30ISO 100 EV 0 00:22:16Safe to Fly (GPS)MODECLP-GPSH: D:V.SM/S M/SH.S24.28.3 1.2M2M39M200m0 200m0[16][15][14][13] [11][12][10][9][8][7][6][5][4][3][2][1]
36 © 2015 DJI. All Rights Reserved. DJI Pilot App Phantom 3 Advanced User Manual[1] Flight Mode: The text next to this icon indicates the current ight mode. Tap to enter MC (Main Controller) Settings. Modify ight limits, perform compass calibration, and set the gain values. [2] GPS Signal Strength: This icon shows the current strength of GPS signals. Green bars indicates adequate GPS strength. [3] IOC Settings : This icon shows which IOC setting that the aircraft has entered when in F Mode. Tap to enter IOC setting menu and select the desired IOC setting.[4] System Status : This icon shows current aircraft system status, such as GPS signal health.[5] Battery Level Indicator : The battery level indicator dynamically displays the battery level. The color zones on the battery level indicator represent different battery levels. [6] Remote Controller Signal : This icon shows the strength of remote controller signal.[7] HD Video Link Signal Strength : This icon shows the HD video downlink signal strength between the aircraft and the remote controller. [8] Battery Level: This icon shows the current battery level.Tap to enter battery information menu, set the various battery warning thresholds and view the battery warning history in this page.[9] General Settings : Tap this icon to enter General Settings page. Select parameter metric, reset the camera, enable the quick view feature, adjust the gimbal pitch value and toggle ight route display on this page. [10] Camera Operation BarShutter : Tap this button to take a single photo. Press and hold this button to select burst or time-lapsed shooting. Record : Tap once to start recording video, then tap again to stop recording. You can also press the Vid-eo Recording Button on the remote controller, which has the same function.Playback : Tap to enter playback page. You can preview photos and videos as soon as they are captured.
© 2015 DJI. All Rights Reserved. 37DJI Pilot App Phantom 3 Advanced User Manual Camera Settings : Tap to enter the camera exposure value setting. User may switch from Auto exposure mode to Advance or Manual mode.[11] MapDisplaytheightpathofthecurrentmission.TaptoswitchfromtheCameraGUItotheMapGUI.[12] Vision Positioning : This icon shows the distance between the surface and the Vision Positioning System's sensors.[13] Flight TelemetryVision Positioning StatusIcon is highlighted when Vision Positioning is in operation.Flightattitudeisindicatedbytheightattitudeicon.(1) The red arrow shows which direction the aircraft is facing.(2) Light blue and dark blue areas indicate pitch.(3) Pitching of the boundary between light blue and dark blue area shows roll angle.[14] Return to Home (RTH) : Initiate RTH home procedure. Tap to have the aircraft return to the last recorded home point.200m0 200m0
38 © 2015 DJI. All Rights Reserved. DJI Pilot App Phantom 3 Advanced User Manual[15] Auto Takeoff/Landing / : Tap to initiate auto takeoff or landing.[16] Back : Tap to return to the main GUI.
© 2015 DJI. All Rights Reserved. 39DJI Pilot App Phantom 3 Advanced User Manual Map User can view the current ight route in a larger map view in this page. You can also perform Auto takeoffand Landing in the page. Ensure your mobile device has access to the Internet. Due to the map datarequired, Wi-Fi connection is recommended. Internet access is required to cache the map, if Wi-Fi isunavailable, mobile data service is required.AcademyDownload user manual, view tutorial videos and practice your ight skills using the simulator in this page. You can also use FilmMaker to create and edit the video clips captured by the aircraft. User CenterYou can sync the picture and videos to the mobile device, view the ight records and check your DJI account status in the User Center. Use the DJI registered account to login to the User Center.
40 © 2015 DJI. All Rights Reserved. FlightThis chapter describes the flight safety and ight restrictions.
© 2015 DJI. All Rights Reserved. 41FlightFlightOnce pre-ight preparation is complete, it is recommended to use the ight simulator in the DJI Pilot App to practice the ight skills and learn to y safely. Ensure that all ights are carried out in a wide open area. Flight Environment Requirements1. Do not use the aircraft in severe weather conditions. These include wind speed exceeding 10 m/s , snow, rain and smog.2. Only y in open areas. Tall and steel structures may affect the accuracy of the on-board compass and GPS signal.3. Avoid approaching the obstacles, crowds, high voltage power lines, trees or bodies of water.4. Minimize electromagnetic interference by not ying in the area with high levels of electromagnetism, including base stations or radio transmission towers. 5. Aircraft and battery performance is subject to environment factor such as air density and temperature. Be very careful when ying 19, 685 feet (6000 m) or more above sea level as battery and aircraft per-formance may be affected.6. The Phantom 3 Advanced cannot operate within the polar areas.Flight Limits and Flight Restriction Area All unmanned aerial vehicle (UAV) operators should abide by all regulations from such organizations as the ICAO (International Civil Aviation Organization), FAA and their own national airspace regulations. For safety reasons, the ight limits function is enabled by default to help users use this product safely and legally. The ight limits function includes height limits, distance limits and No Fly Zones.When operating in “P” Mode, height, distance limits and No Fly Zones work together to manage ight. In “A” mode only height limits work and ights cannot go higher than 1640 feet (500 m) .Maximumightaltitude&RadiusLimitsMaximum ight altitude & Radius limit ying height and distance, and the user may change these settings in the DJI Pilot App. For Be aware that, the maximum ight altitude value cannot exceed 1640 feet (500 m). Once complete, your Phantom 3 Advanced will y in a restricted cylinder that is determined by these settings. The tables below show the details of these limits. Maximum Flight Altitude Max RadiusHome PointHeight of aircraft when powered on
42 © 2015 DJI. All Rights Reserved. FlightPhantom 3 Advanced User ManualGPS Signal Weak Blinking YellowFlight Limits DJI Pilot App Aircraft Status Indicator Maximum Flight AltitudeFlight height restricted to 1640 feet (500 m) and under. Warning: Height limit reached. None.Max Radius No limits If you y out of the limit, you can still control the Inspire, but cannot y it further. If the Inspire ies out of the max radius in Ready to Fly (non-GPS) mode, it will y back within range automatically. Flight Restriction of Restricted Areas Restricted areas include airports worldwide. All restricted areas are listed on the DJI ofcial website at http://www.dji.com/y-safe/category-mc. Restricted areas are divided into category A and category B. Category A areas cover major international airport such as LAX and Heathrow and no-drone zones, while category B areas includes smaller airports.Category A Safety Zone (1) The category A “safety zone” is comprised of a small “no-y zone” and a range of “restricted-altitude zones”. Flight is prevented in the “no-y zone” but can continue with height restrictions in the restrict-ed-altitude zone.(2) A radius of R1 miles (km) around a designated safety zone is a no-y zone, inside which takeoff is prevented. The value of R1 is determined by the size of the airport. (3) From R1 to R1 + 1 miles (R1 + 1.6 km) around restricted areas are altitude restricted, with maximum altitude going from 66 feet (20 m) at R1 miles to 1640 feet (500 m) at R1 + 1 miles (R1 + 1.6 km). (4) A “warning zone” has been set around the safety zone. When you y within 320 feet (100m) of the safety zone, a warning message will appear on the DJI Pilot App.GPS Signal Strong Blinking Green Flight Limits DJI Pilot App Aircraft Status Indicator Maximum Flight AltitudeAircraft's altitude cannot exceed the specied value.Warning: Height limit reached. None.Max Radius Flight distance must be within the max radius.Warning: Distance limit reached.Rapid red ashing when close to the max radius limit.
© 2015 DJI. All Rights Reserved. 43FlightPhantom 3 Advanced User Manual Category B Safety Zone (1) Category B “safety zone” is comprised of a “no-y zone” and a “warning zone”.(2) R mile around the safety zone is a designated “no-y zone”. The value of R is determined by the size of the airport.(3) A “warning zone” has been set around the safety zone. When you y within 0.6 miles (1 km) of this zone, a warning will appear on the DJI Pilot App.R166 feet1 mile320 feet R2Safety Zone1640 feet100m RR166 feet1 mile320 feet R2Safety Zone1640 feet100m R
44 © 2015 DJI. All Rights Reserved. FlightPhantom 3 Advanced User ManualGPS Signal Strong Blinking Green Zone Restriction DJI Pilot App Prompt Aircraft Status Indicator No-y ZoneMotors will not start. Warning: You are in a No-fly zone. Take off prohibited. Red ashingIf the aircraft enters the restricted area in A mode but P mode activates the aircraft will automatically descend to land then stop its motors after landing. Warning: You are in a No-fly zone, automatic landing has begun. (aircraft is entering the area within R1 radius)Restricted-altitude ight zoneIf the aircraft enters the restricted area in A mode but P mode activates, it will descend to a safe altitude and hover 15 feet (4.5 m) below the safe altitude.Warning: You are in a restricted zone. Descending to safe altitude. (If you are between the range of R1 and R2 radius)Warning: You are in a restricted zone. Max ight height restricted to between 20 m and 500 m. Fly Cautiously.(If you are between the range of R1 and R2 radius)Warning zone No ight restriction applies, but there will be warning message.Warning: You are approaching a restricted zone, Fly Cautiously.Free zone No restrictions. None. None.Semi-automatic descent: All stick commands are available except the throttle stick command during the descent and landing process. Motors will stop automatically after landing. When ying in the safety zone, aircraft status indicator will blink red quickly and continue for 3 seconds, then switch to indicate current ying status and continue for 5 seconds at which point it will switch back to red blinking. For safety reasons, please do not y close to airports, highways, railway stations, railway lines, city centers and other special areas. Maintain line of sight of the aircraft.
© 2015 DJI. All Rights Reserved. 45FlightPhantom 3 Advanced User Manual PreightChecklist1. Remote controller, Intelligent Flight Battery, and mobile device are fully charged.2. Propellers are mounted correctly and rmly.3. Micro-SD card has been inserted if necessary.4. Gimbal is functioning as normal.5. Motors can start and are functioning as normal.6. DJI Pilot app connected to the aircraft.Calibrating the CompassIMPORTANT: Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference, which can cause abnormal compass data leading to poor ight performance or even failure. Regular calibration is required for optimum performance. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and steel reinforcements underground. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones. DO NOT calibrate beside massive metal objects. DO NOT calibrate indoors.Calibration ProceduresChoose an open area to carry out the following procedures. 1. Ensure the compass is calibrated. If you did not calibrate the compass in the Checklist, or if you have changed your position since last calibrating it, tap “MODE” in the app and select “Compass Calibration” to calibrate the compass. Then follow the on-screen instructions. 2. Hold and rotate the aircraft horizontally 360 degrees, and the Aircraft Status Indicator will display a solid green light.
46 © 2015 DJI. All Rights Reserved. FlightPhantom 3 Advanced User Manual3. Hold the aircraft vertically with nose pointing downward, and rotate it 360 degrees around the center axis. Recalibrate the compass if the Aircraft Status Indicator show solid red.If the Aircraft Status Indicator blinks red and yellow after the calibration, move your aircraft to a different location to calibrate the compass.Calibrate the compass before each ight. Launch DJI Pilot App, follow the on-screen instruction to calibrate the compass.When to Recalibrate1. When compass data is abnormal, and the Aircraft Status Indicator is blinking red and yellow.2. When ying in a new location, or a location that is different from your last ight. 3. When the mechanical structure of the Phantom 3 Advanced has changed.4. When severe drifting occurs in ight, i.e. Phantom 3 Advanced does not y in straight line.Auto Take-off and Auto LandingAuto Take-offUse auto take-off to take off your aircraft automatically if the Aircraft Status Indicator displays blinking green. Follow the steps below to use auto take-off:1. Launch DJI Pilot app, enter “Camera” page. 2. Ensure the aircraft is in “P” mode.3. Go through the pre-ight checklist. 4. Tap“ ”, and conrm ight conditions. Slide to conrm and take-off. 5. Aircraft takes off and hovers at 1.2 meters above ground. Auto-Landing
© 2015 DJI. All Rights Reserved. 47FlightPhantom 3 Advanced User Manual Flight Test Take off/Landing Procedures 1. Place the aircraft on open, at ground with battery indicators facing towards you.2. Power on the remote controller and your mobile device, then the Intelligent Flight Battery.3. Launch the DJI Pilot App and enter the Camera page.4. Wait until the Aircraft Indicator blinks green. This means the Home Point is recorded and it is safe to y now. If it ashes yellow, it means Home Point is not recorded, and you should not take off.5. Push the throttle up slowly to take off or using Auto Take-off to take off.6. Shoot photos and videos using the DJI Pilot app. 7. To land, hover over a level surface and gently pull down on the throttle slowly to descend.8. After landing, execute the CSC command or hold the throttle at its lowest position for 3 seconds or more until the motors stop.9. Turn off the Intelligent Flight Battery rst, followed by the Remote Controller.Stopping MotorsThere are two methods to stop the motors.Method 1: When Phantom 3 Advanced has landed, push the throttle down , then conduct CSC . Mo-tors will stop immediately. Release both sticks once motors stop.Method 2: When the aircraft has landed, push the throttle down and hold. The motors will stop after 3 seconds.Use auto-landing to land your aircraft automatically if the Aircraft Status Indicator displays blinking green. Follow the steps below to use auto-landing:1. Ensure the aircraft is in “P” mode.2. Check the landing area condition before tapping “ ”, to perform landing. Starting/Stopping the MotorsStarting MotorsA Combination Stick Command (CSC) is used to start the motors instead of simply pushing the stick up. Push both sticks to their bottom corners to start the motors. Once the motors have spun up, release both sticks simultaneously. Method 1 Method 2
48 © 2015 DJI. All Rights Reserved. FlightPhantom 3 Advanced User Manual When the Aircraft Status Indicator blinks yellow rapidly during ight, the aircraft has entered Failsafe mode. A low battery level warning is indicated by the Aircraft Status Indicator blinking red slowly or rapidly during ight. Watch video tutorials about ight for more ight information.Video Suggestions and Tips1. Go through the checklist before each ight.2. Select desired gimbal operation mode in the DJI Pilot app.3. Shoot the video when ying in P mode only.4. Always y in good weather, such as sunny or windless days.5. Change camera settings that suit you. These include photo format and exposure compensation.6. Perform ight tests to establish ight routes and scenes.7. Push the sticks gently to make aircraft movements stable and smooth.
© 2015 DJI. All Rights Reserved. 49FAQ
50 © 2015 DJI. All Rights Reserved. FAQTroubleshooting (FAQ)
© 2015 DJI. All Rights Reserved. 51Appendix
52 © 2015 DJI. All Rights Reserved. AppendixAppendixSpecicationsAircraftWeight (Battery & Propellers Included) 1284 gMax Ascent Speed 6 m/sMax Descent Speed 2 m/sMax Speed 16 m/s (ATTI mode, no wind)Max Flight Altitude 6000 mMax Flight Time Approximately 24 minutesOperating Temperature 0°C to 40°CGPS Mode GPS/GLOSNASSGimbal Controllable Range Pitch - 90° to + 30°Vision PositioningVelocity Range Below 8 m/s (2 m above ground)Altitude Range 5 cm-300 cmOperating Environment Brightly lit (lux > 15) patterned surfacesCamera Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)Lens FOV 94° 20mm(35mm format equivalent ) f/2.8, focus at ∞ISO Range 100-3200(video) 100-1600(photo)Electronic Shutter Speed 8s -1/8000sImage Max Size 4000 x 3000 Still Photography ModesSingle shootBurst shooting: 3/5/7 framesAuto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV BiasTime-lapseSupported SD Card Types Micro SDMax capacity: 64 GB. Class 10 or UHS-1 rating requiredVideo Recording Modes FHD:1920x1080p24/25/30/48/50/60 HD:1280x720p24/25/30/48/50/60Max Bitrate Of Video Storage 60 MbpsSupported File FormatsFAT32/exFATPhoto: JPEG, DNGVideo: MP4/MOV (MPEG-4 AVC/H.264)Operating Temperature Range 0°C to 40°C
© 2015 DJI. All Rights Reserved. 53AppendixPhantom 3 Advanced User Manual Remote Controller Operating Frequency 2.400 GHz-2.483 GHzTransmitting Distance 2000 m (Outdoor And Unobstructed)Video Output Port USB Operating Temperature Range 0°C- 40°CBattery 6000 mAh LiPo 2SMobile Device Holder tablet and phoneWorking Voltage 1.2 A @7.4 VChargerVoltage 17.4 VRated Power 57 W Intelligent Flight Battery ( PH3-4480 mAh-15.2 V )Capacity 4480 mAhVoltage 15.2 VBattery Type LiPo 4SEnergy 68 WhNet Weight 370 gOperating Temperature -10°- 40°Max Charging Power 100 WAircraft Status Indicator DescriptionNormal Red, Green and Yellow Flash Alternatively Power on and self-check Green and Yellow Flash Alternatively Aircraft warming up Green Flashes Slowly Safe to Fly (P mode with GPS and Vision Positioning)X2 Green Flashes Twice Safe to Fly (P mode with Vision Positioning but without GPS) Yellow Flashes Slowly Safe to Fly (A mode but No GPS and Vision Positioning)Warning Fast Yellow Flashing Remote Controller Signal Lost Slow Red Flashing Low Battery Warning Fast Red Flashing Critical Low Battery Warning Red Flashing Alternatively IMU Error — Solid Red Critical Error Red and Yellow Flash Alternatively Compass Calibration Required
54 © 2015 DJI. All Rights Reserved. AppendixPhantom 3 Advanced User ManualIntelligent Orientation Control (IOC)IOC allows users to lock the orientation of aircraft in different fashions. There are three working modes for IOC and you may select the desired IOC modes from the DJI Pilot app. IOC only works under F mode, and user must toggle the ight mode switch to Position 1 to activate IOC. Refer to the table below:Course Lock (CL) Its forward direction is pointing to the nose direction when recording, which is xed until you re-record it or exit from CL.Home Lock (HL)* Record a Home Point (HP), and push Pitch stick to control the aircraft far from or near to the HP. Point of Interest (POI)* Point of Interest. Record a point of interest (POI), the aircraft can circle around the POI, and the nose always points to the POI.*Home Lock and Point of Interest feature are coming soon.Prerequisites of IOCUse the IOC feature under the following condition: Modes IOC GPS enabled GPS counts Flight Distance LimitsCourse Lock No None NoneHome Lock Yes Aircraft ≥10m Home PointPOI Yes Aircraft 5m~500m Point of InterestUsing IOCToggle the Flight Mode Switch “F” mode and follow the instructions prompted on the DJI Pilot app to se-lect the desired IOC features.
© 2015 DJI. All Rights Reserved. 55AppendixPhantom 3 Advanced User Manual FCC Compliance FCC Warning MessageAny Changes or modications not expressly roved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Radiation Exposure Statement: The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The W322A should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in The W322B should be installed and operated with minimum distance 20cm between the radiator& which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC RSS warningThe device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1)The device may not cause interference, and (2)The device must accept any interference,including interference that may cause undesired operation of the device.Le présent areil est conforme aux CNR d'Industrie Canada licables aux areils radio exempts de licence.L'exploitation est autorisée aux deux conditions suivantes:(1) l'areil ne doit pas produire de brouillage, et(2) l'utilisateur de l'areil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.IC Radiation Exposure Statement:This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This W322B should be installed and operated with minimum distance 20cm between the radiator& your body.Any Changes or modications not expressly roved by the party responsible for compliance could void the user’s authority to operate the equipment.
56 © 2015 DJI. All Rights Reserved. AppendixPhantom 3 Advanced User Manual KCC Warning Message“해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .” “해당 무선설비는 운용 중 전파혼신 가능성이 있음”NCC Warning Message低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
© 2015 DJI. All Rights Reserved. The content is subject to change.Download the latest version fromhttp://www.dji.com/product/phantom3If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com.

Navigation menu