Sharp HRO00034 Facsimile Equipment w/ Cordless Handsets User Manual

Sharp Corporation Facsimile Equipment w/ Cordless Handsets

UserManual.wiki >

Sharp >

HRO00034 User Manual >

Manual cordless hanset unit

MODELUX-K022.4GHz Cordless HandsetOPERATION MANUAL Introduction Connecting the Cordless Handset Charger Installing and Charging the Battery Registering the Cordless Handset Enterring a Name for the Cordless Handset Maintenance Charge the battery for about 10 hours before initial use.Cargue la batería durante 10 horas aproximadamente antes del primer uso.TCADH3669XHZZPP

FCC regulatory informationThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and the receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.IMPORTANT NOTICEThis phone (Cordless Handset) has been tested and shown to comply with the FCC RF Exposure guidelines.For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for use with accessories that contains no metal and that positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.The maximum SAR levels tested for this phone (Cordless Handset) has been shown to be 1.220 W/kg at head and 0.446 W/Kg at body.This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the rear of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.If trouble is experienced with this equipment, or for repair or warranty information, please contact Sharp's Customer Assistance Center. The number is 1-877-794-8675. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.This equipment contains no user-repairable parts. Refer all servicing to qualified service personnel.This equipment is hearing aid compatible.This accessory cordless handset, along with the base unit, has received TCB approval.all.book Page 1 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

1EnglishEspañol IntroductionSpecificationsAs a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.Frequency 2.4 GHz (2.405 to 2.475 GHz)Dimensions Width: 1.8" (46 mm)Depth: 1.7" (42 mm)Height: 7.1" (180 mm) (not including antenna)Weight Approx. 0.3 lbs. (115 g) (without battery)Battery 3.6 V Ni-MH battery; capacity: 850 mAhPower consumption Initial chargingBattery lifeBattery life in standbymodeApprox. 1.3 W (in standby mode)Approx. 10 hours for initial chargeApprox. 4 hours (240 minutes) (at room temp.)Approx. 3 days with one full charge (at room temperature)Battery life (both normal and in standby mode) may vary depending on usage, range from base machine, and environmental conditions such as temperature.Thank you for purchasing a UX-K02 cordless handset. To use the UX-K02 cordless handset, you must have a SHARP UX-CD600 fax machine.Battery coverBattery packCordless handset chargerAC adapterAccessoriesOperation manualall.book Page 1 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

2Important safety informationDo not disassemble this product or attempt any procedures not described in this manual. Refer all servicing to qualified service personnel.Do not use this product near water, or when you are wet. For example, do not use this product near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Take care not to spill any liquids on the product.Unplug the product from the power outlet and consult a qualified service representative if any of the following situations occur:- Liquid has been spilled into the product or the product has been exposed to rain or water.- The product produces odors, smoke, or unusual noises.- The power cord is frayed or damaged.- The product has been dropped or the housing damaged.Do not allow anything to rest on the power cord, and do not install the product where people may walk on the power cord.The AC adapter must only be connected to a 120 V, 60 Hz outlet. Connecting it to any other kind of outlet will damage the machine and void the warranty.Never insert objects of any kind into slots or openings on the product. This could create a risk of fire or electric shock. If an object falls into the product that you cannot remove, unplug the product and consult a qualified service representative.Do not place this product on an unstable cart, stand or table. The product could be seriously damaged if it falls.BatteryUse only the battery specified in this manual. Use only the provided charger to charge the battery.Do not open or mutilate the battery pack. Corrosive fluid may leak out and cause injury or burns to the eyes and skin. The fluid may be toxic if swallowed. In case of contact with eyes, flush with clean water (do not rub), and seek medical attention immediately.Do not store or carry the battery with other metal objects such as keys or pins. These may short the battery and cause it to overheat.Do not allow the battery to become wet.Do not dispose of the battery in a fire or heat the battery. The battery may explode.Health care facilities and equipmentRadio frequency energy emitted from the cordless handset equipment may cause medical equipment to malfunction. Verify that any personal medical equipment you are using is adequately shielded from external radio frequency energy before using the cordless handset equipment. Do not use the cordless handset equipment in health care facilities where such use is prohibited.all.book Page 2 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

3EnglishEspañolConnecting the Cordless Handset Charger1Connect the AC adapter to the cordless handset charger.2Plug the AC adapter into a standard 120 V AC outlet.Place the cord in the holders.Installing and Charging the Battery1Connect the battery connector ➊, and then place the battery pack in the cordless handset.2Place the battery cover on the cordless handset, making sure it snaps firmly into place.•Make sure the wires are not caught or pinched by the cover.BlackRedBlackRedImportant: Never cover the charger and AC adapter with a blanket, cloth, or other material. Excessive heating may result, causing a fire.all.book Page 3 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

43Place the cordless handset in the charger with the dial pad facing forward.•Important! The dial pad must face forward, or the battery will not charge. •While charging the first time, the display may show PLEASE REGISTER. Be sure to let the battery charge for 10 hours, and then register the cordless handset as explained on the following page.♦The cordless handset and charger may feel warm while charging. This is normal.♦The battery cannot be overcharged. When not using the cordless handset, keep it in the charger to ensure that it is always charged.Charge the battery at least 10 hours the first time!When the battery needs charging, LOW BATTERY will appear in the display and you will hear beeps during a phone conversation. Place the cordless handset in the charger and let it charge.Note: If the battery is extremely low, nothing may appear in the display during the first several minutes that the cordless handset is in the charger. The battery will begin to charge normally after several minutes.Reinforced concreteMetalAluminum sashTalking range (distance from fax machine) for phone callsThe talking range of the cordless handset for phone calls is approximately 1200 ft. (400 m) (line of sight; talking range may decrease depending on transmission conditions) from the fax machine. If you hear noise or interference while talking, move closer to the fax machine. ♦When outside the talking range, HANDSET? will appear in the display. If you move out of the talking range while talking on the cordless handset, the handset will beep and you may hear interference. Move closer to the fax machine and then press to restore the connection. (Note that in some cases it will not be possible to restore the connection and you will only hear a busy signal.)TALKLarge metal objects, metal structures, and thick walls reduce the talking range.all.book Page 4 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

5EnglishEspañolRegistering the Cordless HandsetHANDSET?After the initial charging, the cordless handset display shows:To use the cordless handset, you must first register it in the machine. During registration, the machine will assign the handset a number.1On the machine, hold down until the display at right appears.2Press on the machine.•Important: Be sure to complete Steps 3 through 5 below while the display at right still appears on the machine.3On the cordless handset, hold down until the display at right appears.4Press on the cordless handset. 5Press on the cordless handset. •The cordless handset display will go dark while registration takes place.6When registration is finished, the number assigned to the cordless handset will appear as shown at right.Note: If you take no action for one minute during the registration procedure, the procedure will be canceled. In this case, start from Step 1 again.INTERCOM/CONFERENCEINTERCOM1STARTMODE SELECT1: HS ENTRY2: HS DELETECordless handset display:Fax machine display:HS ENTRY MODEPRESS START KEYExample: “2” is assignedMODE SELECT1: HS ENTRYMODE SELECT2: HS DELETEHS ENTRYHANDSET 2all.book Page 5 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

6The machine is identified by the number “0”, and the cordless handset that was included with the machine is identified by the number “1”.Entering a Name for the Cordless HandsetEnter a name for the cordless handset in the machine.♦The machine will transmit the name that you enter to your cordless handset. The name will appear in the cordless handset’s display.1Press once and twice on the machine.2Press once and once.3Press once.4Press to select SET. 5Enter the number of the cordless handset for which you wish to enter a name.Example: FUNCTIONExample: Cordless handset 2SELECT HS NO.ENTER (1 - 8)Machine display:ENTRY MODEHS NAME SETHS NAME SET1=SET, 2=CLEARENTER HS NAMEHS2 SELECTEDall.book Page 6 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP

$7EnglishEspañol6Enter the name by pressing number keys for each letter as shown in the chart below. Up to 10 characters can be entered.Example: BILL = 22 444 555 555♦To enter two letters in succession that require the same key, press after entering the first letter. ♦To clear a mistake, press .♦To enter a lower case letter, continue pressing the key for the letter until the lower case letter appears. ♦To enter one of the following symbols, press or repeatedly:. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (7Press to store the name. 8Press to exit.SPEAKERSTART/MEMORYSTOPA =B =C =D =E =F =G =H =I =J =K =L =M =N =O =P =Q =R =S =T =U =V =W =X =Y =Z =SPACE =Machine display:HANDSET2BILLThe handset number and name appear in the standby display:Note: If other cordless handsets for the UX-CD600 are in use when the above procedure is performed, the name of the new cordless handset will not be transmitted to those cordless handsets (the name will not appear by the cordless handset number when is pressed on those cordless handsets to use the intercom and call transfer functions). In this event, repeat the name entry procedure. The stored name automatically appears in the display in Step 6, so simply press to retransmit the name to those cordless handsets, and then exit the procedure with Step 8.INTERCOMSTART/MEMORYOWN NUMBER SETall.book Page 7 Wednesday, January 21, 2004 4:24 PMTCADH3669XHZZPP$