Shuttle P20U All in one PC User Manual

Shuttle Inc. All in one PC Users Manual

Users Manual

P20U Series Quick Guide【English】55oTo place the machine on the desk and to carry it, do the following: Place the P20U on a at surface such as a table. Pull the stand upwards to an angle of 55°. To carry or move your P20U fully extend the angle to 180°.E Placing on the deskE Product OverviewE Cleaning the screenFollow these guidelines for cleaning the outside and handling the screen of the computer:Turn o the system and disconnect all cables. Use a cleaning cloth which is soft, lint-free and a little damp to gently wipe the screen surface. Do not spray liquid directly on the screen. Follow the steps ~ below to connect the AC adapter to the power jack (DC-IN). Press the Power button to turn on the system.E Powering on the system01 LCD display (Multi-touch)02 Webcam status LED03 Webcam04 4G external antenna x 2 (optional)05 Power button06 Kensington® Lock Hole07 Microphone08 SD card reader09 USB 2.0 ports The product’s colour and specications may vary from the actually shipping product.A. Begin InstallationFor safety reasons, please ensure that the power cord is disconnected before opening the case.Latch LatchB. HDD or SSD Installation2. Tear o the adhesive tape of the serial ATA and power cable.1. Replace the back cover and refasten the screws.E. Complete1. Unscrew four screws of the back cover.2. Complete.4. Carefully push down the memory module until it snaps into the locking mechanism.100 x 100mm10 Clear CMOS button11 Microphone jack12 Headphone / Line-out jack13 HDMI port14 USB 3.1 Gen 1 ports15 LAN (RJ45) port16 Power jack (DC-IN)17 Cash drawer (RJ11) port (optional)18 COM 1 and COM 2 ports19 Hard disk drive LED20 Power LED21 MSR with/without transaction support (optional) 22 COM 3 and COM 4 ports (optional)23 Line collection box24 NFC (optional)25 Mono speaker26 Stand / Handle27 D-Sub (VGA) port1. Locate the SO-DIMM slot on the mainboard.3. Gently insert the module into the slot in a 45-degree angle.SO-DIMM slotC. Memory Module Installation2. Align the notch of the memory module with the one of the memory slot.45-degree angle3. Connect the Serial ATA and power cable to the HDD or SSD. Slide the rack into the chassis and refasten the screws.Serial ATA and power cableUse DDR4 SO-DIMM only!53R-P20U03-H001UnscrewThis mainboard does only support 1.2 V DDR4 SO-DIMM memory modules.D. Component Installation2. Install the M.2 device into the M.2 slot and secure with the screw.1. Place an HDD or SSD in the rack and secure with the four screws from the sides. Ax the EMI shielding gasket with the adhesive tape, as shown.Read the following precautions before setting up a Shuttle P20U.CAUTION Do not walk on the power cord or allow anything to rest on it. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. E Safety Information5. Repeat the above steps to install an additional memory module, if required.NotchCutout06050809100714 15 09 16 1702 01032326182211 131219 201. As shown, unfasten the screw rst.E Follow the steps ~ to remove the line collection box cover180oDC-INPower buttonPlace the cable/cord/wire inside the box and stow the extra cable lengths before closing the cover.0421MSR without transaction supportor24 2527Pull the cover outward.Pull it upward.Pull it upward. EMI shielding gasketScrewAdhesive tapeScrewM.2 2242/2260/2280 M key slotBack coverSerial ATA and power cable2. Pull the back cover upward and remove it.MSR with transaction support!!04JP11: USB2 \ USB3 jumper for standby voltagePin1-2 = +5V (Default)3 2 1Daughter board (CM008)Pin2-3 = +5VS (Standby)COM4 (optional) COM3 (optional)COM1COM2JP13: COM port quantity jumperPin1-2 = COM port x 2(Default)3 2 1COM port x 4Pin2-3 = COM port x 3The touch of your nger replaces the input devices and is all you need to operate the P20U.How to use the Touch Panel E VESA mounting it to the wallNote : The P20U can be mounted to a wall using a VESA compatible 100 x 100 mm wall/arm bracket. If you are mounting your P20U to the wall, remove the cover on the back of the P20U rst. Unscrew four screws of the stand mount and remove the stand. The VESA standard lets users mount it on to walls easily. Please refer to the user guide of the wall/arm mount kit you bought separately to install it.

Navigation menu