Symbol Technologies WWC1002SW86S1 2400 MHz Wireless Printer User Manual addendum to operator manual

Symbol Technologies Inc 2400 MHz Wireless Printer addendum to operator manual

Contents

addendum to operator manual

Regulatory AddendumRadio Frequency Interference RequirementsThis device has been tested and found to comply with the limits for a Class A digitaldevice pursuant to Part 15 of the Federal Communications Rules and Regulation. Theselimits are designed to provide reasonable protection against harmful interference whenthe equipment is operated in a commercial environment. This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used in accordance withthe instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential is likely to cause harmful interference inwhich case the user will be required to correct the interference at his own expense.However, there is no guarantee that interference will not occur in a particular installation.If the equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try andcorrect the interference by one of the following measures: • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.This device complies with FCC Part 15. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference and (2) this device mustaccept any interference received, including interference that may cause undesiredoperation.”Radio Frequency Interference Requirements- CanadaThis device complies with RSS 210 of Industry & Science Canada. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference and(2) this device must accept any interference received, including interference that maycause undesired operation.”This Class A digital apparatus meets the requirements of the Industry Canada StandardICES-003.Cet appareil numerique de la Classe A est conforme a la norme NMB-003 du Canada.
CE Marking and European Union Compliance Products intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows, Amendments to these Directives or ENs are included:Applicable Directives• Electromagnetic Compatibility Directive 89/336/EEC• Low Voltage Directive 73/23/EECApplicable Standards• EN 55022-Limits and Methods of Measurement of Radio Interference Characteristics of Information technology Equipment• EN 50 082-1:1997-Electromagnetic Compatibility-Generic Immunity Standard, Part 1: Residential, commercial, Light Industry.• IEC 1000-4-2(1995-01)-Electromagnetic Compatibility (EMC) – Part 4: Testing and measurement techniques-Section 2: Electrostatic Discharge immunity test.• IEC 1000-4-3(1995-03)-Electromagnetic Compatibility (EMC) –Part 4: Testing and measurement techniques-Section 3: Radiated, radio-frequency electromagnetic field immunity test.• IEC 1000-4-4(1995-01)-Electromagnetic Compatibility (EMC) –Part 4: Testing and measurement techniques-Section 4: Electrical Fast transient /burst immunity test.• EN 60 950+Amd1 + Amd @-Safety of Information Technology Equipment Including Electrical Business Equipment• EN 60 825-1 (EN 60 825)- Safety of Devices Containing LasersLaser DevicesSymbol products using lasers comply with US 21 CFR1040.10, Subchapter J and IEC825/EN 60 825 (or IEC 825-1/EN 60 825-1, depending on the date of manufacture). Thelaser classification is marked on one of the labels on the product. Class 1 Laser devices are not considered hazardous when used for their intendedpurpose. The following statement is required to comply with US and internationalregulations:Caution: Use of controls, adjustments or performance of procedures other than thosespecified herein may result in hazardous laser light exposure.Class 2 laser scanners use a low power visible light diode. As with any very bright lightsource such as the sun, the user should avoid staring directly into the light beam.Momentary exposure to a Class 2 laser is not known to be harmful.
RF DevicesSymbol’s RF products are designed to be compliant with the rules and regulations in thelocations into which they are sold and will be labeled as required. The majority ofSymbol’s RF devices are type approved and do not require the user to obtain license orauthorization before using the equipment. Any changes or modifications to SymbolTechnologies equipment not expressly approved by Symbol Technologies could void theuser’s authority to operate the equipment.

Navigation menu