The Kroger SZMDLBTNR1 CC2640R2 BLE 5.0 Module User Manual SREXRG Module

The Kroger Co. CC2640R2 BLE 5.0 Module SREXRG Module

Manual

SRBTNM5 Module User Guide Rev 0.1 Page 1 SRBTNM5 MODULE (CC2640R2 BLE 5.0 Module) USER GUIDE
SRBTNM5 Module User Guide Rev 0.1 Page 2 Contents 1 Introduction .................................................................................................................. 4 1.1 Purpose and scope .................................................................................................. 4 1.2 Revision History ...................................................................................................... 4 2 Module Application Circuit ............................................................................................ 5 2.1 Sample Application Connections ............................................................................. 5 2.2 Compliance Limits ................................................................................................... 6 2.3 Module Power Supply ............................................................................................. 6 3 Antenna Options and PCB Footprint ............................................................................. 7 3.1 Footprint Overview ................................................................................................. 7 3.2 Module Footprint .................................................................................................... 8 4 FCC Compliance Statements .......................................................................................... 9 4.1 End Product Labelling............................................................................................ 10 5 Contact Detail .............................................................................................................. 10
SRBTNM5 Module User Guide Rev 0.1 Page 3 Figures Figure 1: SRBTNM5 Module Application Circuit ............................................................. 5 Figure 2: Header Board Footprint Overview .................................................................... 7 Figure 3: SRBTNM5 Module Footprint Overview ............................................................ 8 Tables No table of figures entries found.
SRBTNM5 Module User Guide Rev 0.1 Page 4 1 Introduction 1.1 Purpose and scope The purpose of this document is to provide details regarding the use of SRBTNM5 Module. This document describes the connections between SRBTNM5 Module and header board. This connection details can be used to mount Module on other Host Board. 1.2 Revision History Date Change Description Revision 21MAR2018 Initial release 0.1
SRBTNM5 Module User Guide Rev 0.1 Page 5 2 Module Application Circuit 2.1 Sample Application Connections Figure 1 shows the circuit connection between SRBTNM5 Module and Debug board. Debug board provide the power supply to the SRBTNM5 Module and has debug header for programming the CC2640R2 chip. Below is the connection diagram of SRBTNM5 module and header board. SRBTNM5ModuleJTAG_TMSJTAG_TCKRESETAVDD and DVDDDGNDDEBUG BOARDChipcon Flashing Header3.3V Voltage ConverterCC2640R2 Debug DataCC2640R2 Debug ClockCC2640R2 Reset3.3V DC0V or GND5V to 12V DC Input Figure 1: SRBTNM5 Module Application Circuit Please refer SRBTNM5 datasheet for module pin description. Based on application requirements, host device can be interfaced with other pins on the module. Please refer TI- CC2640R2 user guide for connection/state information of unused pins.
SRBTNM5 Module User Guide Rev 0.1 Page 6 2.2 Compliance Limits The register value used for FCC compliance is maximum value and cannot be increased by end user. The RF Output Power configuration is not accessible to End User. 2.3 Module Power Supply The SRBTNM5 Module can operate between 2.7V to 3.6V power level. However, it is recommended to provide nominal 3.3VDC supply to Module VCC and GND pins. For details of VCC – GND pins; please refer Module datasheet.
SRBTNM5 Module User Guide Rev 0.1 Page 7 3 Antenna Options and PCB Footprint 3.1 Footprint Overview Below figure shows the footprint detail of the SRBTNM5 Header board. Figure 2: Header Board Footprint Overview
SRBTNM5 Module User Guide Rev 0.1 Page 8 3.2 Module Footprint Figure 3 shows the Module footprint over the Header board Figure 3: SRBTNM5 Module Footprint Overview
SRBTNM5 Module User Guide Rev 0.1 Page 9 4 FCC Compliance Statements FCC ID: PBR-SZMDLBTNR1 FCC Compliance Statements 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including Interference that may cause undesired operation. FCC Caution!!!  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Part 15B compliance statements for digital devices: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates; uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
SRBTNM5 Module User Guide Rev 0.1 Page 10 Following instruction can be included in Final product user manual. Instruction: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operations at closer distances than this are not recommended.” 4.1 End Product Labelling The SRBTNM5 Module is labelled with its own FCC ID Number If the FCC ID Certification Number is not visible while installed inside another device, then the device should display the label on it referring the enclosed module. In that case, the final end product must be labelled in a visible area with the following: “Contains Transmitter Module FCC ID: PBR-SZMDLBTNR1” OR “Contains FCC ID: PBR-SZMDLBTNR1” The OEM should not provide information to the end user regarding installation or removal of this RF module or change RF related parameters in the user manual of the end product. The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). 5 Contact Detail The Kroger Co. 11450 Groom Road Blue Ash, OH-45242, USA

Navigation menu