Tranwo Technology TTA-AB5805R 5.8 GHz Wireless Audio/Video Sender User Manual manual B5805 408 000639 00

Tranwo Technology Corp 5.8 GHz Wireless Audio/Video Sender manual B5805 408 000639 00

Contents

User manual 2 of 2

5.8 GHz Wireless Audio/Video Sender
To prevent fire or shock hazard, do not expose this product to rain and moisture. For example: do not use near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or nearby a swimming pool. To avoid electric shock, do not take apart this product, provided as an accessory. This product should be operated only under power supply. Do not overload wall outlets and extension outlets as this can result in the risk of fire or electric shock.Contents1.Important Safety Information1.Important Safety Information.......................................12.Package Content........................................................23.Panel Control And Function......................................... 34.Setup Guide...............................................................45.Orient Transmitter/Receiver for optimal performance.....51FCC StatementThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note:This equipment has been tested and found to comply with the limits regulated by FCC and CE. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. The change or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.Industry Canada StatementThis device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
2.Package ContentsCheck to make sure that all units shown as below are enclosed.If something missed, please contact your dealer.23. IR Cable LED x 1 2. 5.8GHz Receiver x 1UHF:433.92MHz4. (9V/500mA) x 2 Power Adapters1. 5.8GHz Transmitter x 1 5. Cables x 2EUROPE TypeUSA TypeEUROPE Type(RCA to SCART)USA Type(RCA to RCA)
2.Package Contents3.Panel Control and Function13421. UHF antenna2. ON/OFF switch3. Power indicator/IR windows4. IR mouse jack (transmitter only) Channel selection button to find optimal reception (receiver only)5. Power adapter jack6. DIP switch for ID code, the transmitter and receiver must to be configured as the same ID code.7. Video jack, (yellow), input from source AV equipment8. Audio jack, right (red), input from source AV equipment9. Audio jack, left (white), input from source AV equipment3Transmitter/ReceiverID Code1 2 3ON1 2 3ON1 2 3ON1 2 3ON1 2 3ON1 2 3ONID 21 2 3ON1 2 3ONID 1 ID 4ID 3ID 6ID 5 ID 8ID 761 2 3ON5789
2.Package Contents4.Setup Guide1. Connect one end of the RCA cable (or scart cable) to the RCA jacks, and connect the other end to a source device as well. 2. Connect the DC plug of the adapter to the DC jack, and connect the power supply to an outlet.3. Keep the IR window oriented toward the source AV equipment, or alternatively use the IR Mouse to remotely control it.2.Package ContentsNot e:Mak e su re the ON/OFF swi tch is in the OFF pos ition bef ore conne ct ion「 」TransmitterIR MouseTransmitterTo enjoy a life of wireless video and audio, just connect the transmitter to whatever A/V source you like and connect thereceiver to a TV, monitor or speaker in another location.4OUTReceiver1. Connect one end of the RCA cable (or scart cable) to the RCA jacks, and connect the other end to a TV (or monitor, speakers) on which you like to enjoy a program. 2. Connect the DC plug of the adapter to the DC jack, and connect the power supply to an outlet.3. Keep the IR window oriented toward your remote controller.RemoteControllerReceiverIN* A complete set-up procedure consists of:1. Press “CH” button on receiver, receiver will make transmitter switch to the same channel.2. Make sure the ID on transmitter and receiver is identical (For example, as exhibit Transmitter: Receiver: ) whenever there is problem with installation, please implement the set-up procedure again.1 2 3ONID 11 2 3ONID 1To AV EquipmentTo TV
ReceiverTransmitter5.Orient Transmitter/Receiver for optimal performance5For optimal performance, both the audio/video and remotecontrol antennas should be carefully oriented as describedbelow. For maximum transmitting range, try to minimizeobstacles (e.g. your TV or other electronics, large furniture)where between the transmitter and receiver.Orients the 5.8GHz A/V Antennas5.8GHz Antenna5.8GHz AntennaTransmitter Receiver5.8GHz Antenna 5.8GHz AntennaFig. 1Fig. 2The system delivers high-quality audio and video by using directionalantennas, which must be orientedto get the best results.The antennas are designed tobe able to rotate in almost anydirection.In most situations, the convexof the antennas on both the transmitter and receiver should be facing one another andperpendicular (at a right angle) to an imaginary line drawnbetween the two units. Two examples are shown as Fig.1,Fig.2. Since all homes are different, for optimal reception,additional alignment may be necessary. If the transmitter and receiver are less than 10 feet apart, suggest to lie the antennas on their casings since the distanceis so short.
6Orients the UHF AntennasIn order to obtain optimal performance of the remote controlextender, the remote control antennas should also be orientedat a right angle to an imaginary line drawn between thetransmitter and receiver. If your remote control extender is not working satisfactorily, rotate the remote control antenna on either the transmitter orreceiver 90 degrees so that it is still perpendicular to the pathbetween the units.(See Fig.3)IF you notice improved performance, keep this orientation.Rotating the antenna on both units should have no effect.ReceiverFig. 3TransmitterUHF AntennaUHF Antenna
408-000639-00TTA-B5805TTTA-B5805RThis equipment is intended to be operated in below countries.

Navigation menu