ZIONCOM ELECTRONICS IP04213 300Mbps Wireless N Router User Manual

ZIONCOM ELECTRONICS (SHENZHEN) LTD. 300Mbps Wireless N Router Users Manual

Users Manual

Contents: Wireless Broadband Router, Power adapter, QIG, UTP cable,Installation Helper CD.Hardware Installation If use ADSL access Internet, please comply with step 1, 2, 3, 4 in proper order in below diagram; If use residential broadbandaccess Internet, please complay with step 2, 3, 4, connect your router WAN port to the residential broadband directly.After connected, please check if the indicator light is normal.NameWLAN indicator lightWAN indicator lightLAN indicator lightCPU indicator lightNormal StatusFlashing while data accessLight on or flashingThe corresponding indicator light which connect to PC is on or flashing FlashingNote1. Please disconnect the power adapter and all cable duringthunderstorm;2. Keep away from heat source and keep well ventilated;3. Please pay attention to the waterproofing and moisture-proofwhen storing, transporting and running.4. The power supply must reached the rated current and power.5. Put the router in flat places.Set Up PCWindows 2000 or Windows XP Operating System, please comply with following steps to set up.Right-click “My Network Places”, click “Properties”Right-click “Local Area Connection”, click “Properties”Double-click “Internet Protocol (TCP/IP)”Choose “Obtain an IP address automatically” and “Obtain DNS server address automatically”, click “OK”; go back to previous interface and click “OK”Windows Vista or Windows 7 Operating System, please comply with following steps to set up.Click “Start— Control Panel— Network and Internet— Network Connection”, right-click “Local Area Connection”, and choose “Properties”.Double-click “Internet Protocol Version 4 (TCP/IPv4)”Choose “Obtain an IP address automatically” and “Obtain DNS server address automatically”, click “OK”; go back to previous interface and click “OK”Set Up RouterPlease set up the router as following steps.Run the Web browser.TelephoneWire Telephone Wire TelephoneWire NetworkCableNetworkCableType 192.168.1.1 in the Web browser address bar, and press enter, then click “Setup Tool”. Input user name and password, and then click “OK”. (The default user name and password are “admin”.)Wireless Network ConnectionRight-click “My Network Places”, click “Properties”Right-click “Wireless NetworkConnection”, and click “View Available Wireless Networks”Confirm the wireless network SSID name, choose one that you would like to connect, then click “Connect”Input the encrytion key and click “Connect”Have connected wireless network, you can access Internet through wireless mode.For more information, please go to www.totolink.netInternetAccess ModeDHCPPPPoEStatic IPParameters that provided by ISP (Service Provider)User name & PasswordFixed IP address, Subnet mask, Default gateway and DNS serverISP do not provide any parameters, you can access Internet when without router, no need set up the PC.Access Internet Mode Judgement Method Internet AccessMode SettingsWireless SettingsRouter Security SettingsLAN/DHCP Server SettingsWhen power on, press the button for 5 seconds, the system will be restored to factory settings.Use auto setup wizard CD of TOTOLINK router,can help you to set up the router by one-click. Website: http://www.totolink.netQuick Installation Guide300Mbps Wireless N RouterModel: N302R Plus, IP04213FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu