ZIONCOM ELECTRONICS WX005 300 Mbps Wireless N Range Extender User Manual

ZIONCOM ELECTRONICS (SHENZHEN) LTD. 300 Mbps Wireless N Range Extender Users Manual

Users Manual

For more information, please go to www.totolink.netProduct IntroductionOn: The device is starting up or waiting for extending.Slow-blinking: The device is working normally.Quick-flashing: The device is to restart.Off: The device is power off.On: Extending successfully. Green-Good;Yellow-Normal;Red-Bad.Slow-blinking: The device is extending to upper Router/AP.Quick-flashing: The device is to restart.Off: No extending.WPS: Press the button for about 2-3 seconds to enable WPS. Quick Installation GuideWireless N Range ExtenderInformation in this document is subject to change without prior notice. Copyrights TOTOLINK. All rights reserved. Website: http://www.totolink.netModel No.: EX200V1.1706Method One: Quick Setup by Smart PhonePower on. Plug the device into any wallsocket that near the router. Wait until theSystem LED blinks slowly. 1Login. The Setting page will turn up automatically.Click Extender Mode. If below window doesn’tappear, please open a browser and enter192.168.0.254 manually. 3Connect to the Extender. Using yoursmart phone to search Wi-FiTOTOLINK_EX200. (Settings—Wi-Fi)2Extend Wi-Fi. Wait for a while, the Extenderauto-detects APs nearby. Choose yourrouter’s 2.4GHz SSID.4Configure. Enter its wireless password. Either keepthe default SSID or customize it for extended 2.4GHzwireless network. Verify your settings and click Connect.5Wi-Fi Extended successfully while the Extend LED indicator keeps lighting.6Verify. Check the LED status to verifywhether the Wi-Fi extension issuccessful.FAQ(Frequently Asked Questions)Method Two: Wi-Fi Extension by WPS ButtonPower on. Plug the device into any wallsocket that near the router. Wait until theSystem LED blinks slowly. 1Press WPS button on Extender for about 2 seconds.3SSID: TOTOLINK_EX200 The Extend LED flash whenconnecting and turns to solidlight when connectedPress WPS button on your router for about 2 seconds. 2RST/WPSRelocateHorizon LineHost Network Extended NetworkVertically place the ExtenderWall SocketLAN port: This port is used to connect to PC. RST: Press the button for about 10 seconds, the device will restore to factory default settings. RST Wi-Fi: Upper router’s SSID and passwordThe Extend LED turns to solid light, Wi-Fi extension successful. Please refer to Relocate to place the Extender.4EX200's default Network Name (SSID) is TOTOLINK_EX200 (no encryption). With success repeater connection, this SSID (TOTOLINK_EX200) will change to the same SSID (with same encryption) of upper Router/AP. After deployment, just connect to the Router/AP's SSID. Congratulations, you have extended your WiFi coverage successfully. Plug the extender into wall socket that halfway between yourrouter and the Wi-Fi dead zone. Wait about 30 seconds untilthe Extend LED light turns solid green or yellow. If not, pleaserelocate it closer to your router to achieve better signal quality. 1In order to make full use of extender, please keep the antennasof the extender perpendicular to the horizontal plane. See blow:2What should I do if I cannot access the extender’s web managementpage?A1: Make sure you have connected to the wireless network name of the extender. A2: Open any browser, enter 192.168.0.254 in the address bar and press Enter.A3: Reset the extender and connect to it again. 1How to reset the extender to factory default settings?Keep the extender power on, use a pin to press the RST buttonon the bottom of device. When both System and Extend LED blinks,release the button. The device will restore to factory default settings.2FCC warning: This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference thatmay cause undesired operation.changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment .This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.This equipment should be installed and operated with minimum distance 20cmbetween the radiator& your body.

Navigation menu